A fully charged new battery will have a low conductance reading.

The exit pressure will be 1.3273 bar = 0.1327 MPa and the exit specific internal energy 228.61 KJ/Kg .

1.) In graph,

1-2 = Compressor

3-4 = Throttle value

[tex]T_{1} \\[/tex] = [tex]T_{4}[/tex] = -20°C = 253 K

[tex]T_{3}[/tex] = 25°C = 298 K

[tex]P_{3}[/tex] = 0.8 MPa

Assuming saturated fluid is entering the value at point (3),

using table of R-134a properties

∵ [tex]h_{3} =h_{4}[/tex] = 234.49 KJ/Kg (at 25°C,8 bar)

at [tex]T_{3}[/tex] = 25° , [tex]P_{3}[/tex] = 0.8 MPa =8 bar

At -20°C,   [tex]hf_{4}[/tex] = 173.6 KJ/Kg

                 [tex]hg_{4}[/tex] = 386.6 KJ/Kg

[tex]h_{4} = hf_{3} + n_{4} ( hg_{4} - hf_{4} )[/tex] = 234.49

173.6 + [tex]n_{4}[/tex] [386.6 - 173.6] = 234.49

             [tex]n_{4}[/tex] = 0.285

[tex]P_{4} = P_{1} = P_{sat}[/tex] = 1.3273 bar = 0.1327 MPa

2.)

Exit specific internal energy, using table R-134a

[tex]U_{4} = uf_{4} + n_{4} (ug_{4} - uf_{4} )[/tex]

at -20°c, [tex]uf_{4}\\[/tex] = 173.65, ufg = 192.85 KJ/ Kg

[tex]U_{4}[/tex] = 173.65 + 0.285 (192.85)

[tex]U_{4}[/tex] = 228.61 KJ/Kg

Learn more about Refrigerant here https://brainly.com/question/26395073

#SPJ10

Answer:

That is not a question...

Answer:

the jig grinder provides more precise x- and y-axis movements than a vertical milling machine for extremely accurate positioning

Answer:

HTML (HyperText Markup Language) is the code that is used to structure a web page and its content.

CSS is Cascading Style Sheet.CSS allows you to create great-looking web pages

Explanation:

Answer:

space look at tge explanation

Explanation:

Discuss some of the hazards associated with hot work in confined spaces. Provide specific examples or personal experiences in your response.

The hazards associated with performing hot work include:

Note that when working with anything that cause spark or fire, the common hazard are:

Therefore, The hazards associated with performing hot work include:

Learn more about hazards from

https://brainly.com/question/7310653

#SPJ11

The source port number of the dump given above is 1586. The destination port number is given below.

The destination port number is given as 000DH = 13. Destination port number is determined by running the following command in the Command Prompt: netstat-a

Then you hit the enter button.

The total length of the datagram is given as 001CH = 28 bytes. Datagram is a form of message that is self-contained, that is relayed over the network. It must be noted that it's content cannot be guaranteed.

The length of the data is 20 bytes. This is arrived at by computing the following:

Data Lenght - Header

= 28 - 8

= 20bytes.

It is to be noted that the packet is directed from the client to the sever.

Learn more about ports at;
https://brainly.com/question/18133590
#SPJ1

In ipsec's TRANSPORT mode, the data within an ip packet is encrypted, but the header information is not.

IPSec transport mode is known to be often used if a given tunneling protocol (like GRE) is used to try and encapsulate the IP data packet, and later on, IPSec act as a form of protection for the GRE tunnel packets.

Therefore, In ipsec's TRANSPORT mode, the data within an ip packet is encrypted, but the header information is not.

Learn more about ipsec from

https://brainly.com/question/17299146

#SPJ11

A trap in the condensate line prevents D. All of the above.

It should be noted that the idea of the condensate drain trap is to use the weight of the water to stop the flow of air.

Based on the information given, all the options are correct. Therefore, the correct option is D.

a. air and foreign material from being drawn up into the drain line

b. additional cooling load from warm air drawn up into the air handler

c. insect invasion of the system

d. all of the above

Learn more about cooling on:

brainly.com/question/13748261

#SPJ12

Answer:

c is the answer because we have to double the number

A non-shielded cable should have a 3.0 in minimum bending radius and a 1.5 in maximum diameter. As a result, choice (C) is the right response.

Based on their architecture, these cables are typically divided into two classes: shielded cables and unshielded cables.

Shielded twisted pair (STP) cable is another name for shielded cables. It has distinct wire pairs that are foil-wrapped. To offer double protection, these pairs are wrapped one more time. The shielding aids in preventing EMI and other technical problems that can jeopardize the signal integrity.

Unshielded cable, also known as unshielded twisted pair cable (UTP), is a type of cable in which the individual wire pairs are simply wrapped in foil without any additional layers of protection. Office settings with low traffic are best suited for unshielded wires.

Hence option (C) is accurate.

Learn more about unshielded cables, from:

brainly.com/question/28501202

#SPJ2

The lane that can be used for both entering and exiting a highway is called; A weave lane

When it comes to road highways, there are different terminologies that apply such as Acceleration lane, Deceleration Lane, Interchange, Weave lane, Urban roadway e.t.c

However, when it comes to the one that can be used for both entering and exiting a highway, the correct answer will be Weave Lane because it has both an entrance and an exit for an expressway. Traffic may come onto and leave the expressway at the same location.

Read more about road highway at; https://brainly.com/question/12961781

#SPJ12

Chemicals pose a variety of hazards the six (6) types of health hazards are Corrosives, Irritants, Sensitizers, Carcinogens, Mutagens,Flammable.

To become aware of if a substance is dangerous, test the product's box label and/or the SDS that is to be had from the supplier. If a product isn't categorized as a dangerous chemical beneathneath the Work Health and Safety Act 2011, a SDS isn't required and consequently might not be availableIn the workplace, we discover  varieties of chemical dangers: fitness dangers and physicochemical dangers.1Asphyxiants.

There are many varieties of dangerous chemicals, such as neurotoxins, immune agents, dermatologic agents, carcinogens, reproductive toxins, systemic toxins, asthmagens, pneumoconiotic agents, and sensitizers.

Read more about the health :

https://brainly.com/question/1382377

#SPJ1

If  we have 20-ampere circuit breakers. The  number of circuits to the larger whole number is: 13.

Receptacles on a single strap= 180 VA each.

Hence,

VA of the circuit=(Volts x Amperes)/One receptacle

Let plug in the formula

VA of the circuit=(120 volts x 20 amperes)/180 VA

VA of the circuit= 2,400 VA (circuit)/180 VA

VA of the circuit = 13 circuits

Therefore the  number of circuits to the larger whole number is: 13.

Learn more about number of circuits here:https://brainly.com/question/2969220

https://brainly.com/question/19790289

#SPJ12

When electric power is transferred over a long distance then, line loss can be reduced by high voltage and low current. Thus, option A is correct.

The complete question is attached to the image below.

The electric circuit transfers the electric current then it is called electric power. The loss in the line over a larger distance is reduced by transferring AC instead of DC voltage.

The AC transmitted is of high voltage, and the power is low. The equation for current is given,

P = VI

The increase in the voltage causes the decrease in the current and in turn the resistance also reduces resulting in the loss of the power of the circuit to decrease.

Therefore, the loss is reduced by transferring high voltage and, low current AC.

Learn more about high volatge AC here:

https://brainly.com/question/18069892

#SPJ1

Explanation:

1 answer

The area of triangle with vertices A(0, 9), B(0, 4) and C( - 5, - 9) is

Answer:

It gives a circle

Explanation:

The complete stress distribution obtained by superposing the stresses produced by an axial force and a bending moment is correctly represented by F/A - (My)/(Iz).

Compressive and tensile forces expand withinside the path of the beam axis beneath neath bending loads. These forces set off stresses at the beam. The most compressive pressure is observed on the uppermost fringe of the beam whilst the most tensile pressure is positioned on the decrease fringe of the beam.

The bending pressure is computed for the rail through the equation Sb = Mc/I, wherein Sb is the bending pressure in kilos in keeping with rectangular inch, M is the most bending second in pound-inches, I is the instant of inertia of the rail in (inches)4, and c is the space in inches from the bottom of rail to its impartial axis.

Read more about beam;

https://brainly.com/question/25329636

#SPJ1

Exit lanes give drivers an ample time and space to minimize (reduce) their speed to what is posted and prepare them for the sharpness of the curve.

A speed limit is the maximum amount of speed that is legally permitted in an area for safety. Hence, this limit must be abided and strictly adhered to by all road users such as drivers of a vehicle.

As a safety precaution, Exit lanes are constructed to give drivers an ample time and space to minimize (reduce) their speed to the required  speed limit posted and prepare them for the sharpness of the curve.

Read more on safety here: https://brainly.com/question/14751268

#SPJ12

The person that is correct is Technician A as electrical circuit resistance causes voltage drop.

It should be noted that an electric circuit is the path through which electric changes flow in order to conduct current.

In this case, the person that is correct is Technician A as electrical circuit resistance causes voltage drop.

Learn more about circuit on:

brainly.com/question/2969220

#SPJ12

Neither of the technicians are correct.

A technician simply means an individual who looks after the technical equipments in a company.

In this case, the teeth of the synchronizer are not rounded, the synchronizer can be reused. This shows that he is incorrect likewise technician B.

Learn more about technicians on:

brainly.com/question/1548867

#SPJ12

Creep can be described as a process of the slow rise of plastic deformation under the action of shear stresses when it is below the yield strength of the material. Hence, Option C is correct.

Permanent deformation can be defined as irreversible, the deformation remains even after the elimination of the carried out forces, at the same time as the transient deformation is recoverable because it disappears after the elimination of carried out forces.

therefore, the correct statement is  Option C.

Learn more about permanent deformation

https://brainly.com/question/10667384

#SPJ1

Answer:

i don't know

please mark me brainlist

The back-fill used for underground wiring shall not damage the raceways,  cables, and conductors or prevent adequate compaction of fill or contribute to corrosion.

A unique form of electric wiring or cable this is designed to be buried in a trench underground is known as Direct-burial cable. The character electric accomplishing wires in the cable are encased in a strong thermoplastic sheath that seals out moisture and protects the accomplishing wires within.

The complete question is given below:

(a) raceways

(b) cables

(c) conductors

(d) all of these

Thus, The back-fill used for underground wiring shall not damage the raceways,  cables, and conductors or prevent adequate compaction of fill or contribute to corrosion.

learn more about electrical wiring:

https://brainly.com/question/24786034

#SPJ1

Answer:

Cylindrical

Explanation:

A cylindrical grinder is a tool for shaping the exterior of an item. Although cylindrical grinders may produce a wide range of forms, the item must have a central axis of rotation. Shapes such as cylinders, ellipses, cams, and crankshafts are examples of this. Cylindrical grinding machines are specialized grinding machines that are used to process cylinders, rods, and similar workpieces. The cylinders revolve in one direction between two centers, while the grinding wheel or wheels are close together and rotate in the other direction.

Answer:

r h ch y TC GG ch hh h h

No se

Explanation:

No seibibk h j h uh t t t

The information depicted shows that both technicians are correct.

This is an individual who overlooks the technical equipment in an organization.

In this case, on the full floating axle, there are two tapered roller bearings between the hub and the outside of the axle housing.

Also in a semi-floating axle, the axle supports the weight of the vehicle and is also subject to bending forces as the vehicle corners.

Therefore, they're both correct.

Learn more about technicians on:

brainly.com/question/1548867

#SPJ12

(a) If a kitten weighs 99 grams at birth, it is at 5.72 percentile of the weight distribution.

(b) For a kitten to be at 90th percentile, the minimum weight is 146.45 g.

In a normal distribution curve;

M - 2d = 125 g - 2(15g) = 95 g

M - d = 125 g - 15 g = 110 g

95 g is at 2% and 110 g is at 16%

(16% - 2%) = 14%

(110 - 95) = 15 g

14% / 15g = 0.93%/g

From 95 g to 99 g:

99 g - 95 g  = 4 g

4g x 0.93%/g = 3.72%

99 g will be at:

(2% + 3.72%) = 5.72%

Thus, if a kitten weighs 99 grams at birth, it is at 5.72 percentile of the weight distribution.

M + d = 125 + 15 = 140 g      (at 84%)

M + 2d = 125 + 2(15) = 155 g   ( at 98%)

155 g - 140 g = 15 g

14% / 15g = 0.93%/g

84% + x(0.93%/g) = 90%

84 + 0.93x = 90

0.93x = 6

x = 6.45 g

weight of a kitten in 90th percentile = 140 g + 6.45 g  = 146.45 g

Thus, for a kitten to be at 90th percentile, the approximate weight is 146.45 g

Learn more about standard deviation here: https://brainly.com/question/475676

#SPJ1

In a basketball game, point guard A intends the speed as 47.76 ft/sec, and the launch angle will be 41.084°.

The projectile motion is given as the motion of the object in the curved path near the earth's surface. The throwing of the ball will follow the projectile motion.

The missing image is attached below.

The given game situation consists of:

Velocity of shooting guard (vs) = 12 ft/sec.

Distance from B to C (sc) = 20 ft

Final height to catch the ball, 7 ft

The total distance to cover from B to C = 60 ft

Time is taken to reach B to C = Distance/Speed

Time to reach B to C = 20ft/12ft/sec

Time to reach B to C = 1.667 sec.

The time taken to cover the horizontal distance:

Distance = Velocity * Time

60³ = v₀cosθ * distance/time

60³ =  v₀cosθ * 20/12

v₀cosθ  = 36 ft/sec

The vertical movement can be given where, g = 32.2 ft/sec²:

s = s₀ + v₀sinθ * time + 1/2 -g time²

7 = s + v₀sinθ * 20/12 - 1/2 32.2 ft/sec² * (20/12)²

v₀sinθ = 31.3875 ft/sec

[tex]\rm v_0 =\sqrt{v_0sin\theta^2\;+\;v_ocos\theta^2}[/tex]

Substituting the values:

v₀ = 47.76 ft/sec

The launch angle for the ball will be:

tanθ = v₀sinθ/v₀cosθ

tanθ = 31.3875/36

tanθ = 0.871

θ = 41.084°

Thus, the speed v₀ of the ball will be 47.76 ft/sec, and the launch angle will be 41.084°.

Read more about projectile motion, here:

https://brainly.com/question/11049671

#SPJ1

The maximum volume flow rate of water is determined as 0.029 m³/s.

The power of the pump is watt is calculated as follows;

1 hp = 745.69 W

7 hp = ?

= 7 x 745.69 W

= 5,219.83 W

η = mgh/P

mgh = ηP

m = ηP/gh

m = (0.82 x 5,219.83)/(9.8 x 15)

m = 29.12 kg/s

V = m/ρ

where;

V = (29.12)/(1000)

V = 0.029 m³/s

Learn more about volume flow rate here: https://brainly.com/question/21630019

#SPJ12