Help what’s the answer?

Help Whats The Answer?

Answers

Answer 1

The product is HI

There are six product molecule

Hydrogen is the limiting reactant

There is one iodine molecule in excess

How do you know limiting reactant?

To determine the limiting reactant in a chemical reaction, you need to compare the number of moles of each reactant present to the stoichiometry of the balanced chemical equation.

The limiting reactant is the reactant that is completely consumed in a chemical reaction, and which therefore limits the amount of product that can be formed. The other reactant, which is not completely consumed, is called the excess reactant.

Learn more about limiting reactant:https://brainly.com/question/14225536

#SPJ1


Related Questions

To determine experimentally if a reaction is exthermic a student should use a

Answers

To determine experimentally if a reaction is exothermic, a student should use a calorimeter. A calorimeter is a device used to measure the heat exchange during a chemical reaction, enabling the student to identify if the reaction is exothermic or endothermic. In an exothermic reaction, heat is released, causing the temperature of the surroundings to increase.

To perform the experiment, follow these steps:

1. Choose the appropriate chemical reaction to test.
2. Prepare the calorimeter by placing a known amount of water in the calorimeter's inner container.
3. Measure and record the initial temperature of the water.
4. Add the reactants (in their appropriate amounts) to the water, and quickly seal the calorimeter to minimize heat loss to the surroundings.
5. Stir the mixture gently to ensure proper mixing and heat distribution.
6. Monitor the temperature change of the water over time, recording the highest temperature reached.
7. Calculate the amount of heat released or absorbed by the reaction using the formula: q = mcΔT, where q is heat, m is the mass of water, c is the specific heat capacity of water, and ΔT is the change in temperature.
8. If the heat calculated is positive and the temperature increased, the reaction is exothermic; if negative and the temperature decreased, the reaction is endothermic.

In conclusion, a student should use a calorimeter to experimentally determine if a reaction is exothermic, as it allows for the accurate measurement of heat exchange and can indicate whether heat is released or absorbed during the reaction.

To know more about exothermic refer here

https://brainly.com/question/31214950#

#SPJ11

How can you determine the specific heat capacity of 1. 0g of yam

Answers

Specific heat capacity is the amount of heat required to raise the temperature of a substance by one degree Celsius per unit of mass.

To determine the specific heat capacity of 1.0g of yam, we can use a simple equation:

q = m × c × ΔT

where q is the amount of heat required, m is the mass of the substance, c is the specific heat capacity, and ΔT is the change in temperature.

To measure the specific heat capacity of yam, we would first need to heat the yam to a known temperature, and then measure the amount of heat required to raise its temperature by a certain amount.

For example, we could heat 1.0g of yam to 25°C and then place it in a known amount of water at a lower temperature, such as 20°C. We could then measure the change in temperature of the water and calculate the amount of heat required to heat the yam.

By rearranging the equation above, we can solve for c:

c = q / (m × ΔT)

We can then substitute in the values we measured and calculate the specific heat capacity of the yam. This process can be repeated several times to obtain an average value for the specific heat capacity of yam.

To know more about Specific heat capacity, visit:

https://brainly.com/question/29766819#

#SPJ11

If we began the experiemtn with 0.70 g of cucl2 x 2 h2o, according to the stoichiometry o the reaction, how much al should be used to complete the reaction withtout either reactant being in excess

Answers

0.70 g of CuCl₂ • 2 H₂O reacts completely with 0.48 g of Al. The molar ratio of CuCl₂ • 2 H₂O to Al is 1:2. The reaction completes without any excess reactant.

The balanced chemical equation for the reaction between CuCl₂ • 2 H2O and Al is:

3CuCl₂ • 2 H₂O + 2Al → 3Cu + 2AlCl₃ + 6H₂O

From the equation, we can see that 3 moles of CuCl₂ • 2 H₂O react with 2 moles of Al. We need to find the amount of Al required to react completely with 0.70 g of CuCl₂ • 2 H₂O.

1 mole of CuCl₂ • 2 H₂O has a mass of (63.55 + 2 x 35.45 + 2 x 18.02) g = 170.48 g

0.70 g of CuCl₂ • 2 H₂O is equal to 0.70/170.48 = 0.0041 moles of CuCl₂ • 2 H₂O

From the balanced equation, we can see that 3 moles of CuCl₂ • 2 H₂O react with 2 moles of Al.

Therefore, the moles of Al required is (2/3) x 0.0041 = 0.0027 moles.

The molar mass of Al is 26.98 g/mol. Therefore, the mass of Al required is:

0.0027 moles x 26.98 g/mol = 0.073 g

Therefore, 0.073 g of Al should be used to complete the reaction without either reactant being in excess.

To know more about the molar ratio refer here :

https://brainly.com/question/17920577#

#SPJ11

Complete question :

If we began the experiment with 0.70 g of CuCl₂ • 2 H₂O, according to the stoichiometry of the reaction, how much Al should be used to complete the reaction without either reactant being in excess? Show your calculations.

What would happen to future island chains if volcanic eruptions stopped occurring on the seafloor?

Answers

If volcanic eruptions were to stop occurring on the seafloor, future island chains would no longer be formed.

This is because most island chains are formed by a geological process called plate tectonics, which involves the movement of tectonic plates and the formation of new crust at mid-ocean ridges through volcanic activity.

At mid-ocean ridges, magma rises from the mantle and solidifies to form new crust, pushing the existing crust away from the ridge.

Over time, this process can create a chain of volcanic islands as the tectonic plate moves across the hotspot, with the oldest islands being farthest from the hotspot and the youngest islands being closest.

Without volcanic eruptions on the seafloor, there would be no new crust formation and no movement of tectonic plates to create island chains.

Over time, the existing islands would be eroded and weathered by natural processes such as wind and water, and their size and shape would change.

However, it's worth noting that volcanic eruptions are not the only way that islands can form. For example, islands can also be formed through the uplift of existing land due to geological processes such as tectonic uplift or the rebound of land following the retreat of a glacier.

However, these processes typically occur over much longer time scales than volcanic island formation at mid-ocean ridges.

To know more about eruptions refer here

https://brainly.com/question/9175156#

#SPJ11

Three 3. 0 L sealed flasks , each at a pressure of 878 mmHg contain He, Ar, and Xe respectively. A) which of the flasks contain the greatest number of moles of gas? b) which of the flasks contain the greatest mass of gas? c) If He flask was heated and Ar flask was cooled, which of the three flasks would be at the highest pressure? d) If the temperature of the He was lowered while the Xe was raised, which of the three gases would have the greatest kinetic energy?

Answers

The total number of moles of gas present in the three 3.0 L sealed flasks containing helium, argon, and xenon respectively, if each flask is at a pressure of 878 mmHg, is 0.447 mol.

To calculate the total number of moles of gas present in the three flasks, we can use the ideal gas law:

PV = nRT

First, we need to convert pressure from millimeters of mercury to atmospheres.

1 atm = 760 mmHg

878 mmHg = 1.153 atm

We can calculate number of moles of gas:

For the helium flask:

[tex]n(He) = (1.153 atm) * (3.0 L) / [(0.08206 L.atm/K.mol) * (273.15 K)] \\n(He) = 0.149 mol[/tex]

For the argon flask:

[tex]n(Ar) = (1.153 atm) *(3.0 L) / [(0.08206 L.atm/K.mol) * (273.15 K)] \\n(Ar) = 0.149 mol[/tex]

For the xenon flask:

[tex]n(Xe) = (1.153 atm) * (3.0 L) / [(0.08206 L.atm/K.mol) * (273.15 K)] \\n(Xe) = 0.149 mol[/tex]

Finally, we can add up the number of moles of gas in each flask to find  total number of moles of gas:

[tex]n(total) = n(He) + n(Ar) + n(Xe) \\n(total) = 0.149 mol + 0.149 mol + 0.149 mol \\n(total) = 0.447 mol[/tex]

To know more about helium flask, here

brainly.com/question/10242192

#SPJ4

--The complete Question is, What is the total number of moles of gas present in the three 3.0 L sealed flasks containing helium (He), argon (Ar), and xenon (Xe) respectively if each flask is at a pressure of 878 mmHg?--

You perform a titration where you add 0.35 m hcl to a flask containing 50 ml of 0.75 m naoh. what is the ph after you add 50 ml of 0.35 m hcl

Answers

The pH after adding 50 mL of 0.35 M HCl to a flask containing 50 mL of 0.75 M NaOH is approximately 12.68.

1. Calculate moles of NaOH: moles = M x V = 0.75 M x 0.05 L = 0.0375 moles


2. Calculate moles of HCl: moles = M x V = 0.35 M x 0.05 L = 0.0175 moles


3. Determine moles of excess OH-: moles = moles of NaOH - moles of HCl = 0.0375 - 0.0175 = 0.02 moles


4. Calculate the concentration of excess OH-: [OH-] = moles / total volume = 0.02 moles / 0.1 L = 0.2 M


5. Determine the pOH: pOH = -log10[OH-] = -log10(0.2) = 0.699


6. Calculate the pH: pH = 14 - pOH = 14 - 0.699 ≈ 12.68

To know more about pH click on below link:

https://brainly.com/question/2288405#

#SPJ11

You have one test tube which contains a white solid that is either agcl (s) or pbcl2 (s). select a reagent that will allow you to differentiate between the two chemical species. if the solid is agcl, what will happen when the reagent is added

Answers

To differentiate between AgCl(s) and PbCl₂(s), we can use a reagent that reacts differently with each compound. One such reagent is a solution of ammonia (NH₃).

When ammonia is added to AgCl(s), it will dissolve the solid and form a colorless, soluble complex ion, [Ag(NH₃)2]+. This is because AgCl is soluble in ammonia due to the formation of the complex ion.

AgCl(s) + 2NH₂(aq) → [Ag(NH₃)2]+(aq) + Cl^-(aq)

On the other hand, when ammonia is added to PbCl₂(s), it will not dissolve the solid, and there will be no observable reaction. This is because PbCl₂ is not soluble in ammonia, and the complex ion does not form.

PbCl₂(s) + 2NH₃(aq) → No observable reaction

Therefore, the addition of ammonia to the test tube containing the white solid will help differentiate between AgCl and PbCl₂.

If the solid is AgCl, it will dissolve in the ammonia solution and form a colorless complex ion, while if the solid is PbCl₂, there will be no observable reaction.

to know more about reagents refer here:

https://brainly.com/question/31228572#

#SPJ11

The method used to find the volume of acid that reacts with a known volume of alkali is called

Answers

The method used to find the volume of acid that reacts with a known volume of alkali is called acid-base titration.

In this method, a solution of known concentration (the titrant) is slowly added to a solution of unknown concentration (the analyte) until the reaction between the two is complete.

The point at which the reaction is complete is determined using an indicator or by measuring the pH of the solution. The volume of titrant required to reach this point is used to calculate the concentration of the analyte solution.

The method is widely used in analytical chemistry to determine the concentration of acids, bases, and other reactive substances in solution.

To know more about titration refer to-

https://brainly.com/question/30046193

#SPJ11

what conclusions can you draw about the relationship between the structure of the fabric molecule and the intensity with which the azo dyes color the fabric?

Answers

apart from being used in dying, it’s used as a indicator

Based on the electron configuration of the two
atoms, predict the ratio of metal cationic (+) atom
to nonmetal anionic (-) atom in the compound.

magnesium 1s22s22p63s2
sulfur 1s22s22p3s23p4

a. 1:1

b. 1:2

c. 2:1

d. 3:1

Answers

Answer is B) 1:2


The electron configuration of magnesium is 1s2 2s2 2p6 3s2, which means it has two valence electrons that it can lose to form a cation with a +2 charge.

The electron configuration of sulfur is 1s2 2s2 2p6 3s2 3p4, which means it has six valence electrons that it can gain to form an anion with a -2 charge.

Since magnesium can form a cation with a +2 charge and sulfur can form an anion with a -2 charge, the ratio of metal cationic (+) atom to nonmetal anionic (-) atom in the compound will be 1:2. Therefore, the answer is b. 1:2.

To know more about electronic configuration:

https://brainly.com/question/26084288

#SPJ11

If you started with 20. 0 g of a radioisotope and waited for 3 half-lives to pass, then how much would remain? 1. 25g
5. 00g
10. 0g
2. 50g​

Answers

Answer: The answer is 2.50g.

I hope this helps and have a great day!

Calculate the equilibrium constant at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen. The data refer to


25°C.


CH4(9) + 2H20(9) = CO2(g) + 4H2(9)


Substance:


AH (kJ/mol)


AGf(kJ/mol)


S (J/K mol):


CH4(g)


-74. 87


-50. 81


186. 1


H2019)


-241. 8


-228. 6


188. 8


CO2(9)


-393. 5


-394. 4


213. 7


H219)


0


0


130. 7

Answers

The equilibrium constant (K) at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen is 8.04×10⁻¹³. This indicates that the reaction strongly favors the reactants, and very little of the products will be formed at equilibrium.

To calculate the equilibrium constant at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen, we use the formula:

[tex]Kc = \left(\frac{{[CO_2][H_2]^4}}{{[CH_4][H_2O]^2}}\right)[/tex]

where [ ] denotes concentration in moles per liter. We need to first determine the concentrations of the various species at equilibrium. For this, we use the Gibbs free energy change (ΔG) of the reaction, which is related to the equilibrium constant through the equation:

[tex]\Delta G^\circ = -RT \ln(Kc)[/tex]

where R is the gas constant (8.314 J/K mol), T is the temperature in Kelvin (25°C = 298 K), and ΔG° is the standard free energy change for the reaction, which can be calculated from the standard free energy of formation (ΔGf°) values of the reactants and products:

[tex]\Delta G^\circ = \sum n\Delta G_f^\circ(\text{products}) - \sum m\Delta G_f^\circ(\text{reactants})[/tex]

where n and m are the stoichiometric coefficients of the products and reactants, respectively. Using the given values, we get:

[tex]\Delta G^\circ = [1(-394.4) + 4(0)] - [1(-50.81) + 1(-241.8) + 2(0)][/tex]

ΔG° = -805.37 J/mol

Substituting this value and the other given values into the equation for ΔG°, we get:

[tex]Kc = e^(-ΔG°/RT)[/tex]

[tex]Kc = e^(-805.37/(8.314×298))[/tex]

Kc = 8.04×10⁻¹

Therefore, the equilibrium constant at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen is 8.04×10⁻¹³.

To know more about the  equilibrium constant refer here :

https://brainly.com/question/19671384#

#SPJ11

If 450.5 calories of heat energy are added to a 89.6 gram sample of aluminium (specific heat of 0.215 calories per gram degree celsius) and the initial temperature of the sample is 25.7 degrees celsius then what is the final temperature in degrees celsius?​

Answers

The final temperature is 49.2 degrees Celsius.

To find the final temperature, we can use the formula:

Q = mcΔT

where Q represents the amount of heat energy measured in calories (450.5 calories), m represents the mass of the substance in grams (89.6 grams), c represents the specific heat capacity in calories per gram per degree Celsius (0.215 calories/gram degree Celsius), and ΔT represents the change in temperature.

First, we need to find the change in temperature (ΔT):

450.5 calories = (89.6 grams) * (0.215 calories/gram degree Celsius) * ΔT

Now, we can solve for ΔT:

ΔT = 450.5 calories / [(89.6 grams) * (0.215 calories/gram degree Celsius)] ≈ 23.5 degrees Celsius

Since we know the initial temperature (25.7 degrees Celsius), we can find the final temperature:

Final temperature = Initial temperature + ΔT = 25.7 degrees Celsius + 23.5 degrees Celsius ≈ 49.2 degrees Celsius

Know more about Heat Energy here:

https://brainly.com/question/25384702

#SPJ11

Explain use the tyndall effect to explain why it is more difficult to drive through
fog using high beams than using low beams.

Answers

The Tyndall effect is the scattering of light by colloidal particles or suspensions, causing the particles to become visible.

In fog, water droplets act as colloidal particles and scatter light, making it difficult to see clearly. High beams produce a greater amount of light, which causes more scattering and reflection in the fog, resulting in decreased visibility. This is because the water droplets in the fog are closer together and more concentrated in the path of the high beams, causing more light to be reflected back towards the driver's eyes.

Using low beams, on the other hand, produces less light and reduces the amount of scattering and reflection in the fog, resulting in better visibility. Therefore, it is recommended to use low beams when driving in foggy conditions to avoid glare and improve visibility.

To learn more about Tyndall effect, here

https://brainly.com/question/14431922

#SPJ4

a solution contains 1.30×10-2 m silver nitrate and 6.45×10-3 m lead acetate. solid sodium iodide is added slowly to this mixture. a. what is the formula of the substance that precipitates first?

Answers

To determine the substance that precipitates first, we need to compare the Ksp values for the possible precipitates. The ionic equation for the reaction is:

AgNO3 + Pb(CH3COO)2 + 2NaI → AgI↓ + PbI2↓ + 2NaNO3 + 2CH3COONa

The Ksp expression for AgI is:

Ksp = [Ag+][I-]

The Ksp expression for PbI2 is:

Ksp = [Pb2+][I-]2

The solubility product constant (Ksp) for AgI is 8.5 × 10^-17 and the Ksp for PbI2 is 1.4 × 10^-8.

To determine which substance will precipitate first, we need to compare the Qsp (the reaction quotient) to the Ksp values for AgI and PbI2. At the point of precipitation, Qsp = Ksp.

For AgI:

Qsp = [Ag+][I-] = (1.30×10^-2)(2x) = 2.60x10^-2

For PbI2:

Qsp = [Pb2+][I-]2 = (6.45×10^-3)(2x)^2 = 2.58x10^-2

The substance that will precipitate first is the one with the higher Qsp/Ksp ratio, which is PbI2. Therefore, the formula of the substance that precipitates first is PbI2.

Visit here to learn more about solubility brainly.com/question/28170449

#SPJ11

NEED HELP ASAP
How would testing such as that done in this lab exercise be valuable in real-world situations?​

Answers

Testing done in lab exercises can be valuable in real-world situations by ensuring the safety, reliability, and efficiency of products and identifying potential flaws or weaknesses before they go to market.

Testing, such as that done in this lab exercise, can be incredibly valuable in real-world situations. For example, the lab exercise may involve testing the durability or strength of a particular material or product. This type of testing can be useful in real-world situations when designing and manufacturing new products. By testing the durability and strength of a material or product, designers and manufacturers can ensure that their products are safe and reliable for consumers to use. Additionally, testing can help identify potential flaws or weaknesses in a product before it goes to market, which can save companies time and money in the long run. Overall, testing is a crucial component of product development and can help ensure that products meet the needs and expectations of consumers.

Know more about Lab testing here:

https://brainly.com/question/27723597

#SPJ11

What volume of 0. 125 m kmno4 is required to yield 0. 180 mol of potassium permanganate, kmno4?.

Answers

1.44 liters of 0.125 M [tex]KMnO4[/tex] solution is required to yield 0.180 mol of [tex]KMnO4[/tex].

To determine the volume of 0.125 M [tex]KMnO4[/tex] solution required to yield 0.180 mol of [tex]KMnO4[/tex], we can use the following formula:

moles = concentration x volume

We can rearrange this formula to solve for volume:

volume = moles / concentration

First, we can calculate the volume of 0.125 M [tex]KMnO4[/tex] solution that contains 0.180 moles of [tex]KMnO4[/tex]:

volume = moles / concentration

volume = 0.180 mol / 0.125 mol/L

volume = 1.44 L

Therefore, 1.44 liters of 0.125 M [tex]KMnO4[/tex] solution is required to yield 0.180 mol of [tex]KMnO4[/tex].

To know more about yield refer to-

https://brainly.com/question/30700754

#SPJ11

An aqueous solution of sodium acetate, nach3coo, is made by dissolving 13.8 grams of sodium acetate in sufficient water in a 300. ml volumetric flask, and then adding enough water to fill the flask to the mark. what is the weight/volume percentage of sodium acetate in the solution?

Answers

The weight/volume percentage of sodium acetate in the solution is 4.6%.

The weight/volume percentage of sodium acetate in the solution can be calculated using the formula:
Weight/volume percentage = (Weight of solute ÷ Volume of solution) x 100%

In this case, the weight of sodium acetate is 13.8 grams and the volume of solution is 300 ml.

Therefore,
Weight/volume percentage = (13.8 g ÷ 300 ml) x 100%
Weight/volume percentage = 0.046 x 100%
Weight/volume percentage = 4.6%

Therefore, the weight/volume percentage of sodium acetate in the solution is 4.6%.

To know more about weight/volume percentage visit:

https://brainly.com/question/28751781

#SPJ11

A 2. 50g sample of zinc is heated, then placed in a calorimeter containing 60. 0g of water. The temperature of water increases from 20. 00 degrees C. The specific heat of Zinc is 0. 390J/g Degree C. What was the initial temperature of the zinc metal sample?

Answers

We can use the equation:

q(zinc) = -q(water)

where q(zinc) is the heat lost by the zinc and q(water) is the heat gained by the water.

q(zinc) = m(zinc) × C(zinc) × ΔT

where m(zinc) is the mass of zinc, C(zinc) is the specific heat of zinc, and ΔT is the temperature change of the zinc.

The heat gained by the water :

q(water) = m(water) × C(water) × ΔT

where m(water) is the mass of water, C(water) is the specific heat of water, and ΔT is the temperature change of the water.

Since the calorimeter is assumed to be perfectly insulated, we can assume that the heat lost by the zinc is equal to the heat gained by the water:

m(zinc) × C(zinc) × ΔT = m(water) × C(water) × ΔT

m(zinc) × C(zinc) = m(water) × C(water)

2.50 g × 0.390 J/g°C = 60.0 g × 4.184 J/g°C

ΔT = q(water) / (m(water) × C(water))

= (2.50 g × 0.390 J/g°C) / (60.0 g × 4.184 J/g°C)

= 0.00916°C

Since we know the initial temperature of the water is 20.00°C, we can use the formula for temperature change:

ΔT = final temperature - initial temperature

Rearranging this formula, we get:

initial temperature = final temperature - ΔT

Substituting the given values, we get:

initial temperature = 20.00°C - 0.00916°C

= 19.99084°C

Therefore, the initial temperature of the zinc metal sample was approximately 19.99°C.

To know more about temperature change refer here:

https://brainly.com/question/28884653

#SPJ11

Question 1 options: calculate the energy, in joules, of a photon that has a frequency of 3.73 x 1014 s-1.

Answers

The energy of a photon can be calculated using the equation E = hf, where E is the energy of the photon, h is Planck's constant, and f is the frequency of the photon.

Substituting the given values, we get:

E = (6.626 x 10⁻³⁴ J s) x (3.73 x 10¹⁴ s⁻¹)

E = 2.47 x 10⁻¹⁹ J

Therefore, the energy of the photon with a frequency of 3.73 x 10¹⁴ s¹ is 2.47 x 10⁻¹⁹ J.

This value may seem small, but it is consistent with the fact that photons with higher frequencies (and thus higher energies) are required to cause certain types of chemical reactions and ionization processes.

The energy of a photon with a frequency of 3.73 x 1010¹⁴ s¹ is calculated using the equation E = hf, where h is Planck's constant. The energy of the photon is found to be 2.47 x 1010⁻¹⁹ J.

To know more about the energy of a photon refer here :

https://brainly.com/question/2393994#

#SPJ11

20. 0 g of Potassium reacts with water to produce Potassium hydroxide and hydrogen gas.


2 K + 2 H2O —> 2 KOH + H2


How many miles of hydrogen are there?

Answers

When 20.0 g of Potassium reacts with water, 0.256 moles of hydrogen gas are produced.

To determine the moles of hydrogen produced when 20.0 g of potassium reacts with water to form potassium hydroxide and hydrogen gas, follow these steps:

1. Determine the molar mass of potassium (K): The atomic weight of potassium is 39.1 g/mol.

2. Calculate the moles of potassium (K) used: moles = mass / molar mass
  moles of K = 20.0 g / 39.1 g/mol ≈ 0.512 moles

3. Use the stoichiometry of the balanced equation to find the moles of hydrogen (H₂) produced: 2 moles K produce 1-mole H₂, so the ratio is 1:0.5.

4. Calculate the moles of H₂ produced: moles of H2 = moles of K * (1 mole H₂ / 2 moles K)
  moles of H₂ = 0.512 moles * (1/2) ≈ 0.256 moles

So, when 20.0 g of potassium reacts with water to produce potassium hydroxide and hydrogen gas, there are approximately 0.256 moles of hydrogen.

Learn more about moles at https://brainly.com/question/29367909

#SPJ11

Calcium Carbonate reacts with HCl to produce Calcium chloride, carbon dioxide and water.(I) calculate the number of moles of CO2 produced from 36.5g of HCl (ii) Calculate the amount of Calcium chloride produced (in g) when 3 moles of calcium Carbonate reacts with HCl

Answers

Answer:

i. 0.50 mol CO2

ii. 332.94g CaCl2

Explanation:

CaCO3 + 2HCl -> CaCl2 + CO2 + H2O

i. 36.5g HCl * 1 mol HCl/36.46g HCl * 1 mol CO2/2 mol HCl  = 0.50 mol CO2

ii. 3 mol CaCO3 * 1 mol CaCl2/1 mol CaCO3 * 110.98g CaCl2/1 mol CaCl2 = 332.94g CaCl2

If you have 500 ml of a 0.10 m solution of the acid, what mass of the corresponding sodium salt of the conjugate base do you need to make the buffer with a ph of 2.08 (assuming no change in volume)

Answers

The mass of the corresponding sodium salt of the conjugate base needed to make a buffer with a pH of 2.08.

To determine the mass of the corresponding sodium salt of the conjugate base needed to make a buffer with a pH of 2.08, you can follow these steps:

1. Identify the given information:
  - Initial volume of acid solution: 500 mL
  - Initial concentration of acid solution: 0.10 M
  - Desired pH: 2.08

2. Use the Henderson-Hasselbalch equation:
  pH = pKa + log ([conjugate base]/[acid])

3. Assuming the acid is a weak monoprotic acid (HA) and its conjugate base is A-, determine the pKa:
  pKa = pH - log ([A-]/[HA])

4. Calculate the ratio of [A-] to [HA]:
  [A-]/[HA] = 10^(pH-pKa)

5. Calculate the moles of HA in the 500 mL of 0.10 M solution:
  moles of HA = (volume x concentration) = 500 mL x 0.10 mol/L = 0.050 mol

6. Calculate the moles of A- needed:
  moles of A- = moles of HA x ([A-]/[HA]) ratio

7. Determine the molar mass of the sodium salt of the conjugate base (A-) using the molecular formula.

8. Calculate the mass of the sodium salt of the conjugate base:
  mass = moles of A- x molar mass of A-

By following these steps, you will be able to determine the mass of the corresponding sodium salt of the conjugate base needed to make a buffer with a pH of 2.08.

To know more about conjugate base refer here: https://brainly.com/question/30086613#

#SPJ11

If the balloon was filled up to a volume of 2. 0 L at room temperature (25oC), what will the new volume be if the balloon is placed in the freezer for a few hours at -20oC?Gay-Lussac’s Law.

Answers

The new volume, by using Gay-Lussac's Law, of the balloon after being placed in the freezer would be 1.3 L.

Gay-Lussac’s Law, also known as the pressure-temperature law, states that the pressure and temperature of a gas are directly proportional to each other, provided that the volume and the amount of gas remain constant.

This law is represented mathematically as P1/T1 = P2/T2, where P1 and T1 represent the initial pressure and temperature, and P2 and T2 represent the final pressure and temperature.

In this case, we can use Gay-Lussac’s Law to determine the new volume of the balloon after being placed in the freezer. Since the amount of gas and the volume remain constant, we can rearrange the equation to solve for the new volume.

First, we need to convert the temperatures to Kelvin (K) since the equation requires absolute temperature. To do this, we add 273.15 to the given temperatures. Therefore, the initial temperature (25oC) is 298.15 K, and the final temperature (-20oC) is 253.15 K.

Using the equation P1/T1 = P2/T2, we can solve for the new pressure at the final temperature:

P2 = P1(T2/T1) = (1 atm)(253.15 K/298.15 K) = 0.85 atm

Now that we have the final pressure, we can use the ideal gas law to determine the new volume:

PV = nRT

V2 = (nRT2)/P2

Assuming that the amount of gas and the gas constant (R) remain constant, we can simplify the equation to:

V2/V1 = T2/T1(P2/P1)

Plugging in the given values, we get:

V2/2.0 L = (253.15 K)/(298.15 K)(0.85 atm)/(1 atm)

Simplifying this equation, we get:

V2 = 1.3 L

Therefore, the new volume of the balloon after being placed in the freezer would be 1.3 L.

To know more about Gay-Lussac's Law, visit:

https://brainly.com/question/1358307#

#SPJ11

What is the concentration of hydrochloric acid, HCL(aq) that gives a solution with a pH of 3.69?

Answers

To solve this problem, we need to use the pH formula:

pH = -log[H+]

where [H+] represents the concentration of hydrogen ions in moles per liter (M).

To find [H+], we can rearrange the formula:

[H+] = 10^(-pH)

Substituting pH = 3.69, we get:

[H+] = 10^(-3.69) = 2.21 × 10^(-4) M

Since hydrochloric acid is a strong acid, it completely dissociates in water to give hydrogen ions and chloride ions:

HCl(aq) → H+(aq) + Cl-(aq)

Therefore, the concentration of hydrochloric acid required to give a solution with a pH of 3.69 is also 2.21 × 10^(-4) M.

Sort the disciptions of open clusters and globular clusters into the correct categories

Answers

Open clusters:

Found in the disk of the galaxyYoung starsFew hundred to a few thousand starsLoosely bound by gravityIrregular shape

Globular clusters:

Found in the halo of the galaxyOld starsTens of thousands to millions of starsTightly bound by gravitySpherical shape

What are clusters?

Clusters are collections of stars that are gravitationally connected to one another and close to one another in astronomy. Open clusters and globular clusters are the two basic categories into which they can be separated.

While globular clusters are collections of much older stars that are tightly bound together into a spherical shape, open clusters are collections of much younger stars that are relatively loosely bound together.

Find out more on open clusters here: https://brainly.com/question/15222665

#SPJ1

Why is lead (Pb) able to react with different elements ?

Answers

Lead (Pb) is able to react with different elements because it has a relatively low ionization energy, which means that it requires less energy to remove an electron from a lead atom compared to other elements.

Why does lead have low ionization energy?

Low ionization energy makes it more likely for lead to form compounds with other elements by giving up electrons or sharing them in covalent bonds. Additionally, lead has a relatively high atomic mass, which makes it more likely to form ionic compounds with lighter elements that have lower atomic masses.

The ability of lead to react with different elements also depends on the specific conditions under which the reaction occurs, such as temperature, pressure, and the presence of other reactants or catalysts.

Find out more on lead here: https://brainly.com/question/18110420

#SPJ1

Any atom that has 13 protons is an aluminum atom. Which statement best describes what would happen if a proton were added to an aluminum atom?.

Answers

If a proton were added to an aluminum atom, it would result in the formation of a new atom with 14 protons, which is a Silicon atom.

The addition of a proton would increase the atomic number of the aluminum atom by one, changing it to 14, which is the atomic number of silicon. This would result in a change in the electronic configuration of the atom, leading to different chemical properties. The new atom would have one more electron than the original aluminum atom, which would occupy a new orbital. This would result in a change in the valence shell electronic configuration and reactivity of the atom.

To know more about Silicon atoms, here

brainly.com/question/13568870

#SPJ1

When 4 g of a metal carbonate MCO, was dissolved in 160 cm of 1 M hydrochloric acid and then the resultant solution diluted to one litre, 25. 0 cm of this solution required 20. 0 cm' of 0. IM sodium hydroxide solutidn for complete neutralisation, calculate:
(i) The number of moles per litre of excess hydrochloric acid that reacted with sodium hydroxide, NaOH.

(ii) The number of moles per litre of acid that reacted with the carbonate.

(iii) The number of moles of carbonate, MCO, that reacted with the acid.

(iv) The formula mass of the carbonate, MCO, (v) The atomic mass of the metal M. (C = 12. 0. 0 = 16. 0)​

Answers

(i) The number of moles per litre of excess hydrochloric acid that reacted with sodium hydroxide, NaOH, is 0.2.

(ii) The number of moles per litre of acid that reacted with the carbonate is 0.04.

(iii) The number of moles of carbonate, MCO, that reacted with the acid is 0.008.

(iv) The formula mass of the carbonate, MCO, is the sum of the atomic masses of the carbon, oxygen and metal atoms, i.e., MCO, M + 12 + 16 = M + 28.

(v) The atomic mass of the metal M can be determined by subtracting 28 from the formula mass of the carbonate. Thus, M = formula mass of MCO - 28.

In summary, the given information is used to calculate the number of moles per litre of excess hydrochloric acid, the number of moles per litre of acid that reacted with the carbonate, the number of moles of carbonate that reacted with the acid, the formula mass of the carbonate and the atomic mass of the metal.

Know more about  Hydrochloric acid here

https://brainly.com/question/15231576#

#SPJ11

Drag and drop the words that accurately complete the chart below. Example a lion and a cheetah mistletoe on a tree a coyote eating a rabbit a remora and a shark clownfish and anemone parasitism friendship competition Type of Symbiosis mutualism 1:10 predation relationship commensalism collaboration alliance​

Answers

Answer:

Lion and cheetah - Competition

Mistletoe on a tree - Parasitism

Coyote eating rabbit- Predatation

Remora and Shark - Mutualism

Clownfish and Anemone - Relationship

Explanation:

Other Questions
which of the following is not a growth factor for harmful bacteria a)water b)oxygen c)protein d)minerals 5. Daniel arrives at his campsite out of breath from his swim and jog. His sister tells him that he should have swam to the boat ramp that is only 200 feet from the campsite and then jogged. She claims that he would have arrived quicker this way. Is Daniel's sister correct? Support your answer mathematically Use the appropriate compound interest formula to find the amount that will be in each account, given the stated coins, $47.000 invested at 5% annual interest for 5 years compounded (a) annually: (b) semiannually Fran is training for her first marathon, and she wants to know if there is a significant difference between the mean number of miles run each week by group runners and individual runners who are training for marathons. She interviews 32 randomly selected people who train in groups, and finds that they run a mean of 49. 0 miles per week. Assume that the population standard deviation from group runners is known to be 4. 2 miles per week you have been assigned to watch a couple suspected of potential terrorist plots. you are told to record their every move outside of the house, including who they meet with and for how long. which step in the intelligence process is this? A motorist travelled from Town A to Town B. After travelling for 1 1/2 hours , he passeda cyclist travelling at an average speed of 45 Km/h in the opposite direction.when the motorist reached Town B 2 h later, the cyclist was 30 km away from Town A.a) Find the average speed of the motorist.b) Find the distance between Town A and Town B. What type of thermal energy is the result of molecules colliding Explain the principles of electromagnetism (discuss permeability, reluctance, and magnetomotive force. Describe a basic electromagnet. Also discuss how current is induced in a conductor. What are some applications that use electromagnets? Working with Formulas HELP PLS. Find the area of each of the figures the attendance at a school festival was 786 on Friday night,908 on Sunday, and 812 on Sunday. What was the total attendance? What is the main purpose of lobbying?A man is convicted of a crime but did not have an attorney to represent him at his trial. Under what circumstances would this be unconstitutional according to Gideon v. Wainwright? Help me write a few research questions for the literature review on "freshwater fish pond in the school" Find the are of the shaded shape below it has two lines of symmetry (vertical and horizontal) that pass through its centre Give your answer in cm^2 Question 7 of 20Why should people learn the skill of connecting the past and present?OA. To learn how one person's actions affected many other peopleOB. To learn about the cultures of different countries and societiesOC. To keep from making the mistakes other people have madeOD. To find out what people in the past believed about their worldSUBMIT A uniform plank AB of mass 20kg is supported horizontally at 20cm and 70cm marks from A the plank is in equilibrium when massese 50kg and 70kg are suspended at A and B respectively and the weight of 100N is suspended at the 40cm Mark from B The space available for a relay race at a carnival is 92.75 yards. A rules sign is placed 5 yards before the starting line. If there are 5 sections of thstart to finish and each section covers the same distance, how long is each section of the race?Each section of the race is (blank) yards long Fred harvey wanted the best for his diners to have a unique dining experience. he had special items on each table. these items were: In ms. Oaks class 5/12 of the students wear glasses, 2/9 of the students wear earrings, 2/18 of the students wear hats, and 1/4 of the students wear a watch. No one wears more than one of these items. 4 students wear hats. A. How many students are in ms. Oaks class? b. Determine how many students wear each type of item. please explain how you got the answer, im having trouble figuring out how to find the answer Noah edits the school newspaper. He is planning to print a photograph of a flyer for the upcoming school play. The original flyer has an area of 576 square inches. The picture Noah prints will be a dilation of the flyer using a scale factor of . What will be the area of the picture of the flyer in the newspaper?