Calculate the pressure exerted by a girl on the ground if her mass is 50 kg and the area


of her shoes in contact with the ground is (a) 150 cm2 (high heels); (b) 400 cm2 (flat


soles). (take gravitational field strength g= 10 n kg)

Answers

Answer 1

The pressure exerted by the girl on the ground is (a) 33,333.33 N/m² (Pa) with high heels and (b) 12,500 N/m² (Pa) with flat soles.

To calculate the pressure exerted by the girl on the ground, we will use the formula:

Pressure (P) = Force (F) / Area (A)

Force (F) can be calculated using the formula F = mass (m) × gravitational field strength (g).

For this problem, mass (m) = 50 kg and gravitational field strength (g) = 10 N/kg.

First, let's calculate the force exerted by the girl:

F = m × g = 50 kg × 10 N/kg = 500 N

Now we will calculate the pressure exerted for both cases:

(a) High heels with an area of 150 cm²:
We need to convert the area to m², so A = 150 cm² × (1 m² / 10,000 cm²) = 0.015 m².

Pressure (P) = F / A = 500 N / 0.015 m² = 33,333.33 N/m² or Pa.

(b) Flat soles with an area of 400 cm²:
We need to convert the area to m², so A = 400 cm² × (1 m² / 10,000 cm²) = 0.04 m².

Pressure (P) = F / A = 500 N / 0.04 m² = 12,500 N/m² or Pa.

So, the pressure exerted by the girl on the ground is (a) 33,333.33 N/m² (Pa) with high heels and (b) 12,500 N/m² (Pa) with flat soles.

To learn more about area, refer below:

https://brainly.com/question/27683633

#SPJ11


Related Questions

Do the Pressure vs. Depth Lab (record Describe how the distance the water
your activity)

•When will the water flow out the farthest: when the water is nearly full, half-full, or nearly empty?

•Hold the bottle over the bucket so that the water will flow out the hole into the bucket and loosen the bottle cap.
Observe the flow of water. PUT THE CAP BACK ON!

•Describe how the distance the water flowed out changed as the depth of the water changed.

fill in the blanks
•The pressure of a fluid _____ as depth increases. So pressure and depth are _____ proportional.
This can be written as _____

Answers

Pressure vs. Depth Lab:

The water will flow out the farthest when the bottle is nearly full.As the depth of the water increased, the distance the water flowed out also increased.The pressure of a fluid increases as depth increases. So pressure and depth are directly proportional.This can be written as P ∝ d, where P is pressure and d is depth.

What is pressure?

Pressure is defined as the force per unit area applied on an object. It is a scalar quantity, which means it only has magnitude and no specific direction.

It is often measured in units of Pascals (Pa), which is equivalent to one Newton of force per square meter of area. Pressure can be caused by the weight of an object, the force applied by a fluid, or the collision of particles with a surface.

Find out more on pressure here: https://brainly.com/question/28012687

#SPJ1

A beam of light travels into a new denser medium causing the speed of light to change to 2.5 x 10 8 m/s. what is the index of refraction for the new medium?

Answers

The index of refraction for the new medium is approximately 1.19917.

To find the index of refraction for the new medium, we can use the formula:

n = c / v

Where:
n = index of refraction
c = speed of light in a vacuum (approximately 3 x 10⁸ m/s)
v = speed of light in the new medium (2.5 x 10⁸ m/s)

In this case, we know that the speed of light in the medium (v) is 2.5 x 10⁸ m/s. The speed of light in a vacuum (c) is 299,792,458 m/s.

So, we can calculate the index of refraction (n) as:

n = c/v = 299,792,458 m/s / 2.5 x 10⁸ m/s = 1.19917

Therefore, the index of refraction for the new medium is approximately 1.19917.

For more about refraction:

https://brainly.com/question/14760207

#SPJ11

If charge X has a magnitude of 5x10^-9 C, charge Y would have


an approximate charge of ____________________ C

Answers

Assuming charge Y has the same magnitude as charge X (5x10^-9 C), the approximate charge of Y would also be 5x10^-9 C.

In this assumption, we are considering that charge Y has the same magnitude as charge X, which is 5x10^-9 C. This means that both charges carry the same amount of electric charge. The notation "C" represents coulombs, which is the unit of electric charge.

By assuming that charge Y has the same magnitude as charge X, we are implying that both charges are equal in strength but may have opposite polarities.

Charges can either be positive or negative, and their interactions depend on their polarity. If charge X is positive, then charge Y would also be positive in order for them to have the same magnitude. Similarly, if charge X is negative, then charge Y would also be negative.

It's important to note that this assumption is based on the given information and does not take into account any specific context or additional factors that may affect the charges.

In real-world scenarios, the charges of different objects or particles can vary, and their interactions depend on various factors such as distance, medium, and other electric fields present in the surroundings.

Therefore, the approximate charge of Y is 5x10^-9 C, assuming that it has the same magnitude as charge X.

To learn more about magnitude, refer below:

https://brainly.com/question/14452091

#SPJ11

Explain boyle’s law in terms of the kinetic-molecular theory of gases.

Answers

Boyle's Law states that, at constant temperature, the pressure of a gas is inversely proportional to its volume. This law can be explained and understood using the kinetic-molecular theory of gases.

According to the kinetic-molecular theory, gases are composed of particles (atoms or molecules) that are in constant random motion. These particles collide with each other and with the walls of the container they are in. The pressure of a gas is the result of these collisions.

When the volume of a gas is decreased, the same number of gas particles are confined to a smaller space. As a result, the particles have less space to move around, and they collide more frequently with each other and with the walls of the container. The increased frequency of collisions leads to an increase in the pressure exerted by the gas.

Conversely, when the volume of a gas is increased, the gas particles have more space to move around, and they collide less frequently with each other and with the walls of the container. The decreased frequency of collisions leads to a decrease in the pressure exerted by the gas.

Therefore, according to the kinetic-molecular theory, as the volume of a gas decreases, the gas particles collide more frequently, resulting in an increase in pressure. This observation is consistent with Boyle's Law, which states that the pressure of a gas is inversely proportional to its volume at constant temperature.

To know more about Boyle's Law refer here

https://brainly.com/question/21184611#

#SPJ11

Because the human body is a holistic organism, this means that



A. Each person reacts to stress the same way



B. Physical injuries do not affect mental processes



C. Religion plays a key role in how people react to stress



D. A negative effect in one area can affect others areas

Answers

Because the human body is a holistic organism, this means that D. A negative effect in one area can affect others areas.

This is because all the components of the human body are interconnected, and any disturbance in one part may have repercussions on other parts as well.

When there is a negative effect or disturbance in one area of the body, it can indeed have repercussions on other areas. Here are a few reasons why this occurs:

Physiological Systems: The human body is composed of several physiological systems, such as the cardiovascular system, respiratory system, digestive system, and nervous system, among others.

These systems work in harmony to maintain homeostasis and support each other's functions. Disruption or dysfunction in one system can affect the functioning of other systems, as they are interdependent.

Communication Pathways: The body relies on complex communication pathways to transmit signals and information between different organs and tissues. Hormones, neurotransmitters, and electrical impulses are examples of the communication mechanisms involved.

When there is an issue in one area, it can interfere with the signaling pathways and disrupt the communication network, potentially impacting other areas that rely on these signals.

Compensation Mechanisms: The body often has built-in compensation mechanisms to adapt and maintain balance when faced with challenges or disturbances.

However, if a negative effect persists or overwhelms the compensatory abilities, it can lead to imbalances or compromises in other areas that are trying to compensate. This can manifest as symptoms or further complications.

Blood Circulation: Blood circulation plays a vital role in distributing oxygen, nutrients, and various substances throughout the body.

Any disruption in blood flow, such as blockages or decreased perfusion, can affect multiple organs and tissues, as they rely on a steady supply of oxygen and nutrients for proper functioning.

To learn more about circulation, refer below:

https://brainly.com/question/16144348

#SPJ11

I need help commenting this post, in a paragraph.

Answers

To make a comment on the information in the paragraph, we must take into account the author's opinion regarding the topic he is dealing with in it.

How to make a comment on the paragraph?

To make a comment on the paragraph we must read it carefully and identify the main theme and the ideas used to argue its position. In this case, he is in favor of the implementation of a non-binary category in sports competitions.

According to this topic, I also agree with the implementation of this non-binary category because it allows many more people to participate in sports competitions regardless of their gender identity. Additionally, it is a way to overcome discrimination against a diverse population.

Learn more about comments in: https://brainly.com/question/30318947

#SPJ1

in an rlc series circuit as shown, there is a phase angle between the instantaneous current through the circuit and the instantaneous voltage vad across the entire circuit. for what value of the phase angle is the greatest power delivered to the resistor? group of answer choices 900 2700 zero 1800

Answers

The phase angle that maximizes the power delivered to the resistor is zero degrees. So, correct option is C.

In an RLC series circuit, the impedance Z is given by the equation Z = R + j(XL - XC), where R is the resistance, XL is the inductive reactance, and XC is the capacitive reactance. The current in the circuit is given by the equation I = V/Z, where V is the voltage across the circuit.

The power delivered to the resistor in the circuit is given by the equation P = I^2R. To maximize this power, we need to maximize the current I in the circuit.

The phase angle between the current and voltage is given by the equation tan(phi) = (XL - XC)/R, where phi is the phase angle. This means that the phase angle is zero when XL = XC, or when the reactances cancel out.

At this point, the impedance of the circuit is purely resistive and is equal to R. This means that the current is at its maximum value, which maximizes the power delivered to the resistor.

Therefore, correct option is C.

To learn more about phase angle click on,

https://brainly.com/question/29331145

#SPJ4

Complete question is:

in an rlc series circuit , there is a phase angle between the instantaneous current through the circuit and the instantaneous voltage vad across the entire circuit. for what value of the phase angle is the greatest power delivered to the resistor? group of answer choices

A)90

B)270

C) zero

D) 180

Information:



A jet of steam at 100℃ is directed for a short time on to a large block of ice at 0℃. Some of the steam condenses to form water and some ice is melted. The condensed steam forms 0. 40 kg of water at 0℃.



Questions:



1. Calculate the heat given out by this steam in changing to water without change in temperature. [Take the specific latent heat of vaporization of water as 2 200 kJ/kg].



2. Calculate the heat given out by this water as it cools to the temperature of the ice. [Take the specific heat capacity of water to be 4. 2 kJ/(kg K). ]

Answers

The heat given out by the steam in changing to water without change in temperature 880 kJ. and the heat given out by the water as it cools to the temperature of the ice is 0 kJ.

What is temperature?

Temperature is a measure of the amount of thermal energy present in a system. It is measured using a thermometer and is typically expressed using the Celsius, Fahrenheit, or Kelvin scales. Temperature affects how substances react and interact, how fast molecules move, and how quickly chemical reactions take place.

1. The heat given out by the steam in changing to water without change in temperature can be calculated using the equation Q = m x L,
where m is the mass of the steam and L is the specific latent heat of vaporization.
As 0.40 kg of water condenses from the steam, the mass of the steam is 0.40 kg.
The specific latent heat of vaporization of water is 2 200 kJ/kg.
Therefore, the heat given out by the steam in changing to water without change in temperature is 0.40 kg x 2 200 kJ/kg = 880 kJ.

2. The heat given out by the water as it cools to the temperature of the ice can be calculated using the equation Q = m x c x ΔT,
where m is the mass of the water,
c is the specific heat capacity of water, and
ΔT is the change in temperature.
The mass of the water is 0.40 kg.
The specific heat capacity of water is 4.2 kJ/(kg K). The change in temperature is 0℃ - 0℃ = 0 K.
Therefore, the heat given out by the water as it cools to the temperature of the ice is 0.40 kg x 4.2 kJ/(kg K) x 0 K = 0 kJ.

To learn more about temperature
https://brainly.com/question/30015989
#SPJ4

Co-efficient of volume expansion of
aluminium

Answers

The coefficient of volume expansion of a material is a measure of how much its volume changes with a change in temperature. For aluminium, the coefficient of volume expansion is approximately [tex]7.1 \times 10^{-5}[/tex] per degree Celsius ([tex]K^{-1}[/tex]).

For aluminium, the coefficient of volume expansion is approximately [tex]23.1 \times 10^{-6}[/tex] per degree Celsius. This means that for every degree Celsius increase in temperature, the volume of aluminium will increase by approximately 23.1 parts per million (ppm).

This coefficient of volume expansion is an important property of aluminium, as it affects its behaviour in a variety of applications. For example, in the aerospace industry, aluminium is used extensively in the construction of aircraft because of its low weight and high strength-to-weight ratio. However, as the temperature of the aircraft changes during flight, the volume of the aluminium components will also change, potentially affecting the structural integrity of the aircraft.

Understanding the coefficient of volume expansion is therefore essential for engineers and designers working with aluminium in a variety of fields, from aerospace to construction to electronics.

To learn more about volume expansion

https://brainly.com/question/31456049

#SPJ4

A horizontal, uniform board of weight 125 n and length 4 m is supported by vertical chains at each ends. a person weighing 500 n is sitting on the board. the tension in the right chain is 125 n.what is the tension in the left chain

Answers

The tension in the left chain is 500 N, which is equal to the weight of the person on the board. Since the board is in equilibrium, the net force and net torque acting on the board must be zero.

Let's consider the forces acting on the board: the weight of the board (125 N) acts downward, the weight of the person (500 N) acts downward at the center of the board, and the tension in each chain acts upward.

Since the tension in the right chain is given to be 125 N, the total upward force acting on the board is 125 N + T (where T is the tension in the left chain).

Therefore, the net force on the board is 125 N + T - 625 N = 0 (where 625 N is the combined weight of the board and person).

Solving for T, we get T = 500 N, which is the tension in the left chain. So the tension in the left chain is 500 N, which is equal to the weight of the person on the board.

To know more about  torque, refer here:

https://brainly.com/question/29024338#

#SPJ11

If the 50-kg crate starts from rest and achieves a velocity of v = 4 m/s



when it travels a distance of 5 m to the right, determine the magnitude of



force P acting on the crate. The coefficient of kinetic friction between the



crate and the ground is μk = 0. 3

Answers

Answer:

given m = 50 kg u = 0 m/s v = 4m/s force = P theta = 30 deg

Explanation:

A 10.0 cm object is 5.0 cm from a concave mirror that has a focal length of 12 cm. what is the distance between the image and the mirror? 3.5 cm –3.5 cm 8.6 cm –8.6 cm

Answers

Concave mirrors in The Mirror Equation. When objects are positioned at a specific location in front of a concave mirror, ray diagrams can be used to establish the image location, size, orientation, and type of image created. Here the distance between the image and the mirror is -8.6 cm. The correct option is D.

In order to retrieve the numerical data on image size and distance that ray diagrams are unable to offer, the Mirror formula is applied. The link between the object distance (v), image distance (u), and focal length (f) is also established by the Mirror formula.

The mirror formula is given as:

1/v + 1/u = 1/f

Based on the distance it is:

1 / f = 1 / d₂ - 1 / d₁

1 / 12 = 1 / v + 1 / 5.0

1 / v = - 7 / 60

d₂ = -8.6 cm

Thus the correct option is D.

To know more about mirror formula, visit;

https://brainly.com/question/30242207

#SPJ12

A vessel is filled with a gas at a temperature 30c and a pressure of 760mmhg calculate the final pressure if the volume of the gas is double while it's heated at 80c

Answers

To solve this problem, we can use the combined gas law, which relates the pressure, volume, and temperature of a gas:

(P1 x V1) / T1 = (P2 x V2) / T2

where P1, V1, and T1 are the initial pressure, volume, and temperature, and P2, V2, and T2 are the final pressure, volume, and temperature, respectively.

First, let's convert the initial temperature of 30°C to Kelvin:

T1 = 30°C + 273.15 = 303.15 K

We can now set up the equation with the initial conditions:

(760 mmHg x V1) / 303.15 K = (P2 x 2V1) / 353.15 K

where V1 is the initial volume of the gas.

Simplifying this equation by multiplying both sides by 303.15 K and dividing by 2V1, we get:

P2 = (760 mmHg x 303.15 K) / (353.15 K) = 653.75 mmHg

Therefore, the final pressure of the gas is 653.75 mmHg when the volume is doubled and the temperature is increased to 80°C.

A small rubber wheel is used to drive a large pottery wheel. The two wheels are mounted so that their circular edges touch. The small wheel has a radius of 2. 8 cm and accelerates at the rate of 6. 0 rad/s2, and it is in contact with the pottery wheel (radius 23. 0 cm ) without slipping. Calculate (a) the angular acceleration of the pottery wheel, and (b) the time it takes the pottery wheel to reach its required speed of 65 rpm

Answers

The angular acceleration of the pottery wheel is 0.728 rad/s², and whereas the time it takes for the pottery wheel to reach its required speed of 65 rpm is 1.93 s.

(a) The small rubber wheel drives the large pottery wheel through frictional forces at their point of contact. Since they are in contact without slipping, the linear speed of the small wheel must be equal to the linear speed of the large wheel.

The linear speed of the small wheel can be found using the formula [tex]v = \omega r,[/tex] where ω is the angular velocity and r is the radius. The small wheel has an angular acceleration of 6.0 rad/s², so its angular velocity increases as  [tex]\omega = \alpha t[/tex] , where t is time.

Substituting the given values, we get v = (6.0 rad/s²)(2.8 cm) t. The linear speed of the large wheel is the same as that of the small wheel, so we can use the formula [tex]v = \omega r[/tex] to find its angular velocity. Substituting the given values, we get  [tex]\omega = v/r[/tex]

[tex]= (6.0\;rad/s^2)(2.8\;cm)/(23.0\cm)[/tex]

= 0.728 rad/s².

(b) The time it takes for the pottery wheel to reach its required speed of 65 rpm can be found using the formula [tex]\omega = (2\pi n)/60[/tex], where n is the rotational speed in rpm.

Solving for n, we get [tex]n = (60 \;\omega)/(2\pi )[/tex]

= (60)(0.728)/(2π)

= 11.6 rpm.

The time it takes to reach this speed can be found using the formula [tex]t = (n - n0)/\alpha[/tex], where n0 is the initial rotational speed (which is zero in this case).

Substituting the given values, we get t = (11.6 rpm - 0 rpm)/(6.0 rad/s²) = 1.93 s.

In summary, A small rubber wheel drives a large pottery wheel through frictional forces. The angular acceleration of the pottery wheel can be found using the formula [tex]\omega = v/r[/tex] where v is the linear speed of the small wheel and r is the radius of the pottery wheel.

The time it takes for the pottery wheel to reach its required speed can be found using the formula t = (n - n0)/α, where n is the final rotational speed and α is the angular acceleration.

To know more about acceleration refer here:

https://brainly.com/question/30413854#

#SPJ11

Explain how to calculate the distance to the epicenter of an earthquake:

step 1:

step 2:

step 3:

Answers

The distance to the epicenter of an earthquake can be calculated by measuring the S-P interval and using a travel-time graph. Data from multiple seismographs are used to triangulate the exact location of the epicenter.

To calculate the distance to the epicenter of an earthquake, the following steps can be followed:

Step 1: Determine the time interval between the arrival of the P-wave and S-wave. This time interval is called the "S-P interval" and can be measured using a seismograph.

Step 2: Use a travel-time graph, which plots the S-P interval against the distance to the epicenter, to find the distance to the epicenter. The graph provides a curve of expected S-P intervals for different distances. By measuring the S-P interval, we can determine the distance from the curve.

Step 3: Repeat the process using data from at least three different seismographs located at different locations to triangulate the exact location of the epicenter.

In summary, the distance to the epicenter of an earthquake can be calculated by measuring the S-P interval and using a travel-time graph to find the corresponding distance. This process is repeated using data from multiple seismographs to triangulate the exact location of the epicenter.

To know more about epicenter refer here:

https://brainly.com/question/28136716#

#SPJ11

which of the following choices gives the amount of power used by a capacitor in an ac circuit? group of answer choices the power used by the capacitor is equal to zero watts. vrmsirms2 irmsxc irmsxc2 vrmsxc

Answers

The power used by a capacitor in an AC circuit is equal to zero watts. Option 3 is correct.

This is because the power used by a capacitor is reactive power, which means that it is not dissipated as heat but is rather stored and released in the circuit. In an AC circuit, the capacitor alternately charges and discharges as the voltage and current change direction, respectively, but the net power used over a complete cycle is zero.

The other choices refer to different formulas for calculating other aspects of an AC circuit, such as the impedance of a capacitor (IrmsXC), the product of the voltage and the impedance (VrmsXC), or the total power in the circuit (VrmsIrms^2). However, none of these formulas give the amount of power used by a capacitor in an AC circuit. Option 3 is correct.

The complete question is

Which of the following choices gives the amount of power used by a capacitor in an ac circuit?

1. IrmsXC^2

2. IrmsXC

3. The power used by the capacitor is equal to zero watts.

4. VrmsXC

5. VrmsIrms^2

To know more about the Capacitor, here

https://brainly.com/question/15088605

#SPJ4

An echo bounces off the side of a mountain which is 290 m away from a hiker who yells at the mountain. If the hiker hears the echo 1.7 s after yelling, how fast was the sound wave traveling?

Answers

The sound wave moved at a speed of about 170.59 m/s.

Do you consider an echo to be a type of sound?

Echoes. An echo is a sound that is reproduced when sound waves are reflected back. Sound waves can also reflect off smooth, hard surfaces, much to way a rubber ball does. The echo sounds the same as the original sound, despite the fact that the sound's direction changes.

Time for sound to reach the mountain and bounce back = 2 x 1.7 s = 3.4 s

The distance traveled by the sound wave is twice the distance between the hiker and the mountain, so:

Distance = (580 m x 2 x 290 m)

Using the formula:

Speed = Distance / Time

we get:

Speed = 580 m / 3.4 s = 170.59 m/s

To know more about speed visit:-

https://brainly.com/question/28224010

#SPJ1

Titan Tommy and the Test Tubes at a night club this weekend. The lead


instrumentalist uses a test tube (closed-end air column) with a 17. 2 cm air column. The


speed of sound in the test tube is 340 m/sec. Find the frequency of the first harmonic


played by this instrument.

Answers

The frequency of the first harmonic played by the instrument is approximately 990.7 Hz.

The frequency of the first harmonic played by the instrument can be calculated using the formula:

f = v / (2L)

where f is the frequency, v is the speed of sound in the test tube, and L is the length of the air column in the test tube.

The speed of sound in test tube is, 340 m/s.

In this case, L = 17.2 cm = 0.172 m. Substituting the given values into the formula, we get:

f = 340 m/s / (2 * 0.172 m)

f = 990.7 Hz

To know more about frequency, here

brainly.com/question/5102661

#SPJ4

A truck driver is trying to push a loaded truck with an applied force.

Unfortunately, his attempt was unsuccessful the truck stays stationary no

matter how hard the driver pushes. How much work is done by the driver?

Answers

The work done by the driver pushing a stationary truck is zero, but the driver still expends energy to overcome the static friction between the truck and the ground.

The work done by the driver pushing a stationary truck with a constant force is zero. This is because work is defined as the product of force and displacement in the direction of force. In this case, the force applied by the driver is in the direction of motion, but since the truck doesn't move, the displacement is zero. Therefore, the work done by the driver is also zero.

However, it's worth noting that even though no work is done on the truck, the driver still expends energy. The energy expended by the driver goes into overcoming the static friction between the truck's wheels and the ground.

Static friction is the force that prevents the truck from moving, and it requires a certain amount of energy to overcome it. This energy is dissipated as heat and sound as the driver pushes against the truck.

To learn more about work done

https://brainly.com/question/31655489

#SPJ4

Find the mass of a circular moving object that has a centripetal force of 1345 N and an acceleration of 36. 2 m/s2?

Ruichao is spinning her backpack around and around. If her backpack has a mass of 8 kg, what centripetal acceleration would it have if she applies a centripetal force of 120 N?


Callum is playing tetherball. The tetherball has a mass of 0. 4 kg and has a tangential velocity of 2. 4 m/s. If the tetherball rope is 1. 5 m long, what centripetal force does Callum’s tetherball have?

Melissa and Cody are on a fun fair ride that spins them in a circle with radius 6 meters. If Melissa has a mass of 55 kg and Cody has a mass of 65 kg, what centripetal force will they have together if they have an acceleration of 2. 2 m/s2?


Bethany is swinging her grocery bag as she walks. The radius of her swing is 0. 8 m. If she can provide a tangential velocity of 2. 7 m/s and a centripetal force of 68 N, what centripetal accel-eration will her groceries have?

Answers

The mass of the object can be found using the formula: m = 37.1 kg and a = 9.13 m/s, and force F = 1.92 N.

1. Mass Finding: Let F = ma =[tex]mv^2/r[/tex]

F is the centripetal force, m is the mass of the object, v is the velocity and r is the radius of the circular path.

Plugging in the given values, we get:

1345 N = m x 36.2 m/s

m = 37.1 kg

a = [tex](2.4 m/s)^2/1.5 m[/tex]

a = 3.84 m/s

2. The centripetal force can be found using the formula:

F = [tex]mv^2/r,[/tex] where m is the mass of the tetherball, v is its tangential velocity and r is the length of the tetherball rope.

Plugging in the given values, we get:

F = [tex]0.4 kg * (2.4 m/s)^2/1.5 m[/tex]

F = 1.92 N

The centripetal force experienced by Melissa and Cody together can be found using the formula:

3. F = (m1 + m2) x a x r, where m1 and m2 are the masses of Melissa and Cody respectively, a is the centripetal acceleration and r is the radius of the circular path.

Plugging in the given values, we get:

F = (55 kg + 65 kg) x 2.2 m/s x 6 m

F = 2376 N

68 N = m x (2.7 m/s)/0.8 m

m = 7.24 kg

a = (2.7 m/s)/0.8 m

a = 9.13 m/s

Learn more about mass Visit: brainly.com/question/86444

#SPJ4

In a circuit, we are using conducting wires made from Manganese If we assume there are 3 free electrons per an atom of manganese, what is its

electron density?

Answers

The electron density of a conducting wire made of manganese can be calculated by multiplying the number of manganese atoms per unit volume by the number of free electrons per manganese atom.

To determine the electron density of a wire made of manganese, we need to know the number of manganese atoms per unit volume and the number of free electrons per manganese atom. The electron density is defined as the number of free electrons per unit volume of the material.

Assuming the wire is made entirely of manganese, we can calculate the number of manganese atoms per unit volume using the density of manganese, which is 7.43 g/cm³. This can be converted to atoms/cm³ using the atomic weight of manganese, which is 54.94 g/mol, and Avogadro's number.

Next, we need to know the number of free electrons per manganese atom, which is given as 3 in the problem statement. Finally, we can calculate the electron density by multiplying the number of manganese atoms per unit volume by the number of free electrons per manganese atom.

In summary, the electron density of a conducting wire made of manganese can be calculated by multiplying the number of manganese atoms per unit volume by the number of free electrons per manganese atom. This requires knowledge of the density of manganese and the number of free electrons per atom.

To know more about density refer here:

https://brainly.com/question/29359462#

#SPJ11

Suppose you were traveling in your family's car. imagine you are at a red light and the light turns green. when the driver puts their foot on the gas petal are they accelerating? help me and ithe next 24 hours, i will put you brainliest nd lots of stars

Answers

Yes, the driver is accelerating when they put their foot on the gas pedal. Acceleration is the rate of change of velocity, which means that any change in speed or direction of motion is considered acceleration.

In this case, when the driver presses on the gas pedal, the car's velocity increases, causing a change in speed.

Therefore, the car is accelerating.

It's important to note that acceleration doesn't only refer to an increase in speed but can also refer to a decrease in speed or a change in direction, such as turning a corner.

To know more about velocity, refer here:

https://brainly.com/question/30559316#

#SPJ11

Please help Anatomy and phys


1. Compare and contrast positive and negative feedback loops of the endocrine system. Provide a specific example of each, including which gland is responsible for the hormone related to that loop.



2. What is the difference between endocrine and exocrine glands in terms of both form and function? Why is one type not considered part of the endocrine system?



3. Describe the cascade of events that occurs when blood glucose levels decline, including which organ and cells respond, which hormones are released, and how the process helps maintain homeostasis. Your answer should cover all three ways glucose is re-introduced to the body. What is the ultimate use of the glucose created in this process?



4. Why can both type I and type II diabetes, untreated, result in impaired vision or blindness as someone ages? How does type II diabetes turn into type I diabetes as someone ages?



5. Imagine you have a patient who has come to you and is exhibiting symptoms such as fatigue and increased thirst and urination. What would you check for to determine whether the patient has Cushing’s, type I diabetes, or type II diabetes?

Answers

When blood glucose levels decline, several organs and cells in the body respond to restore glucose levels and maintain homeostasis. The first response comes from the pancreas, which releases glucagon into the bloodstream. Glucagon stimulates the liver to break down stored glycogen into glucose, which is then released into the bloodstream. This process is called glycogenolysis and is one of the three ways glucose is reintroduced to the body.

The second response comes from the adrenal glands, which release epinephrine and norepinephrine into the bloodstream. These hormones stimulate the liver to break down glycogen into glucose, and they also stimulate the breakdown of fat cells into glucose, a process called lipolysis. This is the second way glucose is reintroduced to the body.

Finally, the third response comes from the kidneys, which can produce glucose through a process called gluconeogenesis. This is the third way glucose is reintroduced to the body.

The ultimate use of the glucose created in this process is to provide energy to the body's cells. Glucose is the primary source of energy for the brain and is also used by muscles and other organs.

If a patient exhibits symptoms such as fatigue and increased thirst and urination, several tests can be conducted to determine if they have Cushing's syndrome, type I diabetes, or type II diabetes. For Cushing's syndrome, tests may include blood and urine tests to measure cortisol levels, as well as imaging tests to check for tumors in the adrenal or pituitary glands.

For type I diabetes, blood tests may be conducted to measure blood glucose and ketone levels, as well as tests to measure levels of antibodies that attack insulin-producing cells. For type II diabetes, blood tests may be conducted to measure blood glucose levels, as well as tests to measure insulin resistance and other metabolic factors.

Additionally, a physical exam may reveal signs such as high blood pressure or excess weight, which can be associated with type II diabetes. Overall, a thorough medical evaluation can help determine the underlying cause of a patient's symptoms and guide appropriate treatment.

To know more about homeostasis refer here

https://brainly.com/question/3888340#

#SPJ11

whats the sum of (8+3m)+(-2+4x)+(9+8d)

Answers

Answer:

15 + 3m + 4x + 8d

Explanation:

On its highest power setting, a certain microwave oven projects 1.00kW of microwaves onto a 30.0 by 40.0 cm area. (A) what is the intensity in W/m^2 ? (B) calculate the peak electric field srength E0 in these waves. (C) what is the peak magnetic field strength B0?we use the equation I=P/A. which gives us the answer 8.33 * 10^3 W/m^2 and then moves on to give us 2I average = 1.67 * 10^4.i dont understand how they got the 2Iave=1.67×10^4

Answers

On its highest power setting, a certain microwave oven projects 1.00kW of microwaves onto a 30.0 by 40.0 cm area. Intensity is 8.33 × 10^3 W/m^2, Peak electric field strength is 4.84 × 10^4 V/m, Peak magnetic field strength is 1.61 × 10^-4 T

(A) To find the intensity (I) in W/m^2, we use the formula I = P/A, where P is power and A is area.

Power (P) = 1.00 kW = 1000 W
Area (A) = 30.0 cm × 40.0 cm = 0.3 m × 0.4 m = 0.12 m^2
I = P/A = 1000 W / 0.12 m^2 = 8.33 × 10^3 W/m²

(B) The average intensity (I_average) is related to the peak electric field strength (E0) by the formula:
I_average = (1/2) × ε0 × c × E0^2
where ε0 is the vacuum permittivity (8.85 × 10^-12 C^2/N·m^2), c is the speed of light (3 × 10^8 m/s), and E0 is the peak electric field strength.
To find the peak electric field strength, first, we'll rearrange the formula to isolate E0:
E0^2 = (2 × I_average) / (ε0 × c)
E0 = sqrt((2 × I_average) / (ε0 × c))
Now, let's plug in the values:
E0 = sqrt((2 × 8.33 × 10^3 W/m^2) / (8.85 × 10^-12 C^2/N·m^2 × 3 × 10^8 m/s))
E0 ≈ 4.84 × 10^4 V/m

(C) To find the peak magnetic field strength (B0), we use the formula:

B0 = E0 / c
B0 = (4.84 × 10^4 V/m) / (3 × 10^8 m/s)
B0 ≈ 1.61 × 10^-4 T

Learn more about microwave oven here:-

https://brainly.com/question/29944171

#SPJ11

Tabletop equipment on legs requires a clearance of.

Answers

The clearance required for tabletop equipment on legs can vary depending on several factors, including the specific equipment and its intended use. However, as a general guideline, a clearance of around 6 to 12 inches (15 to 30 centimeters) is often recommended.

This clearance allows for easy access to the equipment for maintenance, cleaning, and repairs. It also provides space for ventilation and prevents any obstructions that may interfere with the proper functioning of the equipment.

It's important to refer to the manufacturer's specifications or guidelines for the specific tabletop equipment you are using to determine the recommended clearance. These guidelines will provide the most accurate information regarding the clearance requirements for your particular equipment.

To know more about  tabletop equipment refer here

https://brainly.com/question/11799608#

#SPJ11

For what values of h and k does the linear system have infinitely many solutions?.

Answers

A linear system of equations has infinitely many solutions when the equations are dependent, meaning that one equation can be obtained by scaling or combining the other equations. In general, this occurs when the equations represent parallel lines or overlapping lines.

Consider a linear system of two equations:

Equation 1: ax + by = c

Equation 2: dx + ey = f

If these equations have infinitely many solutions, it means that the slopes of the lines represented by the equations are equal (a/b = d/e) and the y-intercepts are also equal (c/b = f/e).

Therefore, for the linear system to have infinitely many solutions, the coefficients of x and y in the equations must be proportional and the constants on the right side of the equations must also be proportional.

In terms of the variables h and k:

Equation 1: hx + ky = c1

Equation 2: dx + ey = c2

For the system to have infinitely many solutions, the coefficients h and d must be proportional (h/d = k/e) and the constants c1 and c2 must be proportional (c1/d = c2/e).

This condition can be simplified to:

h/d = k/e

So, for the linear system to have infinitely many solutions, h and k must be proportional to the respective coefficients d and e.

To know more about linear system refer here

https://brainly.com/question/26544018#

#SPJ11

What affects the thermal conductivity of earth materials? (Ex: Water, Soil, Sand, Air, etc.)

Answers

The factors that affect the thermal conductivity of earth materials include porosity, density, mineral composition, moisture content, etc.

Factors affecting thermal conductivity of earth materials

The thermal conductivity of earth materials depends on several factors, including:

Porosity: The thermal conductivity of earth materials increases with decreasing porosity. Moisture content: The thermal conductivity of earth materials increases with increasing moisture content. Mineral composition: The thermal conductivity of earth materials depends on the relative abundance of different minerals present.Density: The thermal conductivity of earth materials increases with increasing density. Temperature: The thermal conductivity of earth materials generally increases with increasing temperature. Structure: The thermal conductivity of earth materials can also be influenced by their structure, such as the arrangement of particles or the presence of fractures or voids.

More on thermal conductivity can be found here: https://brainly.com/question/7643131

#SPJ1

Two uniform solid spheres have the same mass, 1.75 kg, but one has a radius of 0.206 m while the other has a radius of 0.834 m. for each of the spheres, find the torque required to bring the sphere from rest to an angular velocity of 327 rad/s in 15.5 s. each sphere rotates about an axis through its center. torque on sphere with the smaller radius.

Answers

The torque required for the sphere with the smaller radius is approximately 0.622 N*m.

To find the torque required for each sphere, we need to first calculate the moment of inertia (I) for each sphere, and then use the formula for torque (τ) which is τ = I * α, where α is the angular acceleration.

The moment of inertia for a solid sphere is given by I = (2/5) * M * R^2, where M is the mass and R is the radius.

For the smaller sphere (radius = 0.206 m):
I₁ = (2/5) * 1.75 kg * (0.206 m)^2 ≈ 0.0295 kg*m^2

For the larger sphere (radius = 0.834 m):
I₂ = (2/5) * 1.75 kg * (0.834 m)^2 ≈ 0.5093 kg*m^2

Next, we need to find the angular acceleration (α) using the formula α = Δω/Δt, where Δω is the change in angular velocity and Δt is the time interval.

Δω = 327 rad/s (final angular velocity) - 0 rad/s (initial angular velocity) = 327 rad/s
Δt = 15.5 s

α = 327 rad/s / 15.5 s ≈ 21.1 rad/s^2

Now, we can find the torque (τ) for each sphere using τ = I * α.

Torque for smaller sphere:
τ₁ = 0.0295 kg*m^2 * 21.1 rad/s^2 ≈ 0.622 N*m

Torque for larger sphere:
τ₂ = 0.5093 kg*m^2 * 21.1 rad/s^2 ≈ 10.76 N*m

So, the torque required for the sphere with the smaller radius is approximately 0.622 N*m.

To learn more about acceleration, refer below:

https://brainly.com/question/12550364

#SPJ11

A 15 kg box is moving to the right while being pushed down and to the left as shown in the picture. Force Push is 100 N and = 40°. The coefficient of static friction µS = 0.6 and the coefficient of kinetic friction µK = 0.5

What is the magnitude of Force Normal?
What is the magnitude of Force Friction?
What is the acceleration rate of the box in the x direction?

Answers

The magnitude of the normal force is 147 N.

The  magnitude of Force Friction is 73.5 N.

The acceleration of the box is  0.21 m/s².

What is the magnitude of Force Normal?

The magnitude of the normal force is calculated as follows;

Fn = mg

where;

m is the massg is acceleration due to gravity

Fn = 15 kg x 9.8 m/s²

Fn = 147 N

The  magnitude of Force Friction is calculated as follows;

Ff = μFn

Ff = 0.5 x 147 N

Ff = 73.5 N

The acceleration of the box is calculated as follows;

F - Ff = ma

a = (F - ff)/m

a = (100 x cos40  -  73.5 ) / 15

a = 0.21 m/s²

Learn more about normal force here: https://brainly.com/question/14486416

#SPJ1

Other Questions
The opponent-process theory is most useful for explaining a characteristic of. World Builder is responsible for designing and developing compelling environments using _____ and unique assets. Terrain editorsCADPhotoshopBlender Lines 171182: What are three possible solutions to the problem of violence? Which of these three solutions is most fully developed? Cite details that show how the idea is developed you are 1.9 m tall and stand 3.2 m from a plane mirror that extends vertically upward from the floor. on the floor 1.5 m in front of the mirror is a small table 0.80 m high. what is the minimum height the mirror must have fro you to be able to see the top of the table in the mirror? At constant temperature and pressure, a system is most likely to undergo a reaction so that in its final state, as compared to its initial state, the system has:A) lower energy and higher entropy B) lower energy and lower entropy C) higher energy and lower entropy D) higher energy and higher entropy The enthalpy combustion of ethanol is -1430 kJ/mol. Determine heat given off from the combustion of 1 dm of ethanol. Given density of ethanol is 0.79 gcm. (molar mass ethanol = 46 g/mol) Mr. Thayer wants to measure the height of the CN tower. He stands 320 m from the base of the tower. He uses an inclinometer to measure the angle from the (horizontal) ground to the top of the tower, and it is 60. Assume Mr. Thayer's eyes are 1.6 m above the ground. Neha thinks God is very benevolent and very gracious. To all the things that we want, if they are good for us, He is going to give them to us. Do you agree with her? Give reasons for your answer.The Prayer - Rabindranath Tagore The base of a chest shaped as a rectangular prism is 12 feet and the height is 4 feet.What is the volume? Find all solutions of the equation in radians. sin(2t)cos(t)-cos(2t)sin(t)=0 The company performed another experiment in which they tested three website designs to see which one would lead to the highest probability of a purchase. The first (design A) used enhanced product information, the second (design B) used extensive iconography, and the third (design C) allowed the customer to submit their own product ratings. After 6 weeks of testing, the designs delivered probabilities of purchase of 4.5%, 5.2%, and 3.8% respectively. Equal numbers of customers were sent randomly to each website design. what is the probability that a customer who visited made a purchase? In what phase of postanesthesia care (pacu) is the client prepared for self-care or care in the hospital or an extended care setting What was the Doctrine of Nullification similar to? Write the formula that shows the dependence of the edge length a on the volume V of a cube. The distance from the crest of one wave to the crest of another.19The rising of ocean water bringing nutrients up from the deep.This is what moves forward and through a wave.The amount of dissolved salt in a liquid.As the amount of salt in water increases, the density of the water _________.The length of open sea over which wind can blow steadily to create waves.Water circulation created by prevailing wind systems. The Gulf Stream is an example.Water circulation created by differences in density.The type of energy possessed by moving water.The cyclical process of the changing state and movement of water around the Earth through evaporation, condensation, and precipitation.1. The water cycle2. vapor transport3. salinity4. increases5. decreases6. surface currents7. Coriolis Effect8. deepwater currents9. trough10. wave period11. wavelength12. water molecules13. energy14. crest15. fetch16. electrical17. kinetic18. downwelling19. upwelling Use the given vectors to find v w and vv. v= - 8i 3j, w= - 9i 7j what is the impact of coriolis force and latent heat on the development of tropical cyclones Hi can someone please help me with this (b) The volume of the cylinder is 0. 0020m". The pressure inside the cylinder isinitially 200 atmospheres. When the cylinder is connected to the balloon, the finalpressure in the cylinder and the balloon is 1. 0 atmosphere. The temperature of thegas remains constant. Calculate the final volume of gas in the balloon. State theequation that you use. Which good introduction I can write including this topic ( was the black consciousness successful in challenging the Apartheid Regime in the 1970s)&the line of argument