A simple circuit has a 20 Ω resistor and carries 0. 3 A. The voltage of the power source is 6 V. In a simple circuit with only one resistor, the voltage across the resistor is equal to the voltage of the power source.
Using Ohm's law, we can determine the voltage of the power source by multiplying the resistance (R) of the circuit by the current (I) flowing through it. Thus, we have:
V = IR
Substituting the given values, we get:
[tex]V = (0.3 A)(20\; \Omega) = 6 V[/tex]
Therefore, the voltage of the power source in the circuit is 6 volts. In a simple circuit with only one resistor, the voltage across the resistor is equal to the voltage of the power source.
This is because the sum of the voltages across all the components in the circuit must equal the total voltage of the power source, due to the conservation of energy.
It's important to note that in real-world circuits, the voltage of the power source can fluctuate due to various factors such as fluctuations in the electrical grid or changes in the internal resistance of the power source itself.
To know more about resistors refer here:
https://brainly.com/question/31258648#
#SPJ11
The density of mercury is 13. 6 g/cm³
Calculate the mass of :
a) 1 cm³ of mercury
b) 10 cm³ of mercury
1). The mass of 1 cm³ of mercury is 13.6 g.
2). The mass of 10 cm³ of mercury is 136 g.
1) The mass of 1 cm³ of mercury can be calculated using the density formula:
density = mass / volume
Rearranging the formula to solve for mass, we get:
mass = density x volume
Plugging in the values:
density = 13.6 g/cm³
volume = 1 cm³
mass = 13.6 g/cm³ x 1 cm³
mass = 13.6 g
b) Similarly, to find the mass of 10 cm³ of mercury, we can use the same formula:
mass = density x volume
Plugging in the values:
density = 13.6 g/cm³
volume = 10 cm³
mass = 13.6 g/cm³ x 10 cm³
mass = 136 g
To know more about mercury refer here
https://brainly.com/question/28422859#
#SPJ11
you pull a friend up a 50 m rocky slope with tension force in the rope of 490 N the slope is very steep what work will you need to do in order to pull up your friend
Explanation:
F x d = work
490 N * 50 m = 24 500 J of work
Particles q1, 92, and q3 are in a straight line.
Particles q1 = -1. 60 x 10-19 C, 92 = +1. 60 x 10-19 C,
and q3 = -1. 60 x 10-19 C. Particles 91 and q2 are
separated by 0. 001 m. Particles q2 and q3 are
separated by 0. 001 m. What is the net force on 92?
Remember: Negative forces (-F) will point Left
Positive forces (+F) will point Right
-1. 60 x 10-19 C
+1. 60 x 10-19
-1. 60 x 10-19 C
91
+ 92
93
0. 001 m
0. 001 m
The net force on particle 92 is zero, which means it is in equilibrium and not accelerating.
The electric force between charged particles can be calculated using Coulomb's law, which states that the force is proportional to the product of the charges and inversely proportional to the square of the distance between them.
To find the net force on particle 92, we need to calculate the electric forces acting on it due to the other particles in the line. The force on particle 92 due to particle 91 can be calculated using Coulomb's law:
F_92,1 = kq_1q_2 / r²
= (9x10⁹ Nm²/C²) * (-1.60x10⁻¹⁹ C) * (1.60x10⁻¹⁹ C) / (0.001 m)²
= -2.30x10⁻¹⁴ N
The force on particle 92 due to particle 93 can also be calculated using Coulomb's law:
F_92,3 = kq_2q_3 / r²
= (9x10⁹ Nm²/C²) * (-1.60x10⁻¹⁹ C) * (-1.60x10⁻¹⁹ C) / (0.001 m)²
= 2.30x10⁻¹⁴ N
Since the forces due to particles 91 and 93 are equal in magnitude but opposite in direction, they cancel out each other. As a result, the net force acting on particle 92 is zero.
To know more about the Particles, here
https://brainly.com/question/29023558
#SPJ4
Assuming the precision, P, with which this electromagnetic radiation can shape the cornea is inversely proportional to wavelength (the shorter the wavelength, the higher the precision), how much more precise can this ultraviolet light be than the shortest wavelength of visible light, which is 380 nm
From the relation between precision and wavelength, the precision of UV light is 90.95 % times the precision of visible light.
Given:
Wavelength, λ = 380 nm
Laser wavelength, λ₁ = 199 nm
The relationship between precision and wavelength is:
P ∝ 1/λ
Precision = (P - P₁)÷P₁ ×100
Precision(UV) = (λ₁ ÷ λ) - 1 ×100
Precision(UV) = (380 ÷ 199 - 1) ×100
Precision(UV) = 90.95 %
Hence, the precision of UV light is 90.95 % the precision of visible light.
To learn more about Wavelength, here:
https://brainly.com/question/31322456
#SPJ12
Answer all of these for me, please!! :)
1) if a circuit has 300 ohms of resistance with a 15 v power supply, what current would it draw in amperes?
2) what is the resistance of a circuit that draws 0.02 a with a 300 v power supply?
3)if the resistance of a circuit with 12 a is doubled without changing the voltage, what will be the new current in a?
4)if the resistance of a circuit with 12 a is halved without changing the voltage, what will be the new current in a?
The current would be: I = V/R = 15 V / 300 Ω = 0.05 A. The resistance would be: R = V/I = 300 V / 0.02 A = 15,000 Ω. The new current would be 6 A. The new current would be 24 A.
1) Using Ohm's law, we can determine the current drawn by the circuit by dividing the voltage by the resistance. So, the current would be: I = V/R = 15 V / 300 Ω = 0.05 A.
2) Again, using Ohm's law, we can determine the resistance of the circuit by dividing the voltage by the current. So, the resistance would be: R = V/I = 300 V / 0.02 A = 15,000 Ω.
3) According to Ohm's law, if the resistance of a circuit is doubled without changing the voltage, the current will be halved. So, the new current would be 6 A.
4) Similarly, if the resistance of a circuit is halved without changing the voltage, the current will be doubled. So, the new current would be 24 A.
In summary, Ohm's law relates the current, voltage, and resistance in an electric circuit. By knowing any two of these values, we can calculate the third value using the formula I = V/R.
To know more about Ohm's law, refer here:
https://brainly.com/question/1247379#
#SPJ11
Ice (the solid phase of water) has a lower density than water because:
Using a lever, a person applies 60 n of force and moves the lever 1 m. this moves a 200-newton rock at the other end by 0. 2 m
The force required to move the 200-newton rock using the lever is 300 N.
We can use the principle of mechanical advantage to determine the force required to move the rock using the lever. Mechanical advantage is the ratio of the output force (the force required to move the rock) to the input force (the force applied by the person). It is given by the formula:
mechanical advantage = output force / input force
In this case, the input force is 60 N and the output force is the force required to move the rock, which we can calculate as follows:
output force = input force x mechanical advantage
The mechanical advantage of a lever is determined by the ratio of the distance from the input force to the fulcrum (the pivot point) to the distance from the output force to the fulcrum. This is known as the lever arm ratio.
In this question, we are told that the person moves the lever 1 m and the rock moves 0.2 m. Therefore, the lever arm ratio is:
lever arm ratio = output distance / input distance
= 0.2 m / 1 m
= 0.2
The mechanical advantage is the inverse of the lever arm ratio:
mechanical advantage = 1 / lever arm ratio
= 1 / 0.2
= 5
Substituting this value in the formula for output force, we get:
output force = input force x mechanical advantage
= 60 N x 5
= 300 N
To know more about lever, here
https://brainly.com/question/3977835
#SPJ4
A Helmholtz resonator is a simple cylindrical cavity that suppresses most frequencies and strongly amplifies a few resonant frequencies.
A Helmholtz resonator is essentially an acoustic device that consists of a cavity (usually a cylinder or sphere) with a small neck or opening.
The cavity is typically filled with air, and when sound waves enter the resonator, they cause the air inside the cavity to vibrate at specific resonant frequencies. These frequencies are determined by the size and shape of the cavity, as well as the size and shape of the neck or opening.
One of the key features of a Helmholtz resonator is its ability to suppress most frequencies while strongly amplifying a few specific resonant frequencies.
This is because the resonator acts as a filter, allowing only certain frequencies to pass through the neck or opening and enter the cavity. Any other frequencies are reflected or absorbed by the resonator, resulting in a reduction in overall sound levels.
Helmholtz resonators are commonly used in a variety of applications, such as in acoustic engineering to reduce noise levels in buildings or vehicles, in musical instruments to enhance specific frequencies, and in scientific experiments to study the properties of sound waves.
To learn more about cavity, refer below:
https://brainly.com/question/20515008
#SPJ11
A 0. 41 kg spike is hammered into a railroad
tie. The initial speed of the spike is equal to
1. 4 m/s. If the tie and spike together absorb 40. 4
percent of the spikeâs initial kinetic energy
as internal energy, calculate the increase in
internal energy of the tie and spike.
Answer in units of J.
please and thank you
A 0.41 kg spike is hammered into a railroad tie with 1.4 m/s initial speed. They absorb 40.4% of its initial kinetic energy as internal energy, resulting in an increase of 0.164 J in their internal energy.
To solve this problem, we need to use the conservation of energy principle, which states that the total energy in a closed system remains constant. In this case, the initial kinetic energy of the spike is converted into internal energy of the spike and tie.
The initial kinetic energy of the spike is given by:
[tex]KEi = (1/2) \times m \times v^2[/tex]
[tex]KEi = (1/2) \times 0.41 kg \times (1.4 m/s)^2[/tex]
KEi = 0.4054 J
The internal energy gained by the spike and tie is given by:
[tex]\Delta E = KEi \times 40.4\%[/tex]
[tex]\Delta E = 0.4054 J \times 0.404[/tex]
ΔE = 0.164 J
Therefore, the increase in internal energy of the spike and tie is 0.164 J.
In summary, a 0.41 kg spike is hammered into a railroad tie with an initial speed of 1.4 m/s. The tie and spike absorb 40.4% of the spike's initial kinetic energy as internal energy. Using the conservation of energy principle, we calculate that the increase in internal energy of the tie and spike is 0.164 J.
To know more about kinetic energy refer here:
https://brainly.com/question/7674744#
#SPJ11
Write an expression for the speed of the heavier mass as a function of their separation distance, r, which is measured cm to cm and decreases over time as the masses move toward each other due to their gravitational attraction.
The speed of the heavier mass as a function of their separation distance, r, can be expressed using the conservation of energy principle.
As the masses move toward each other due to gravitational attraction, their potential energy decreases and their kinetic energy increases, such that the total energy remains constant.
Therefore, we can write: 1/2 * m1 * [tex]v^{2}[/tex] = G * m1 * m2 / r
where m1 is the mass of the heavier object, m2 is the mass of the lighter object, v is the velocity of m1, r is the separation distance between the two objects, and G is the gravitational constant.
Solving for v, we get:
v = sqrt(2 * G * m2 / r)
This expression shows that as the separation distance r decreases, the velocity v of the heavier object increases due to the increasing gravitational attraction between the two masses.
To know more about kinetic energy, refer here:
https://brainly.com/question/26472013#
#SPJ11
A tank for storing liquid has a base of area 1. 5msquare what is the pressure on the base of the tank when it contain oil weighing 6000N
The pressure on the base of the tank is: 4000 Pa when it contains oil weighing 6000 N with a base area of 1.5 m².
Pressure is defined as force per unit area. In this case, the force acting on the base of the tank is the weight of the oil, which is given as 6000 N. The area of the base is 1.5 m². Using the formula for pressure, we can calculate the pressure as:
Pressure = Force / Area
Substituting the given values, we get:
Pressure = 6000 N / 1.5 m² = 4000 Pa
Therefore, the pressure on the base of the tank when it contains oil weighing 6000 N with a base area of 1.5 m² is 4000 Pa.
To know more about pressure, refer here:
https://brainly.com/question/31608709#
#SPJ11
Four identical particles of mass 0. 913 kg each are placed at the vertices of a 4. 30 m x 4. 30 m square and held there by four massless rods, which form the sides of the square. What is the rotational inertia of this rigid body about an axis that:
a. Passes through the midpoints of opposite sides and lies in the plane of the square
b passes through the midpoint of one of the sides and is perpendicular to the plane of the square
c. Lies in the plane of the square and passes through two diagonally opposite particles
To calculate the rotational inertia of this rigid body, we need to use the formula I = Σmr², where I is the rotational inertia, Σm is the sum of the masses of all the particles, and r is the distance of each particle from the axis of rotation.
For part b, the axis of rotation passes through the midpoint of one of the sides and is perpendicular to the plane of the square. This means that the distance of each particle from the axis of rotation is the same, which is the half of the diagonal of the square, given by d/2 = 2.415 m. Thus, the rotational inertia can be calculated as I = 4m(2.415)² = 44.2 kg·m².
For part c, the axis of rotation lies in the plane of the square and passes through two diagonally opposite particles. This means that we need to find the distance of the other two particles from the axis of rotation, which can be calculated using the Pythagorean theorem. The diagonal of the square is given by d = 4.30 m, so the distance of each particle from the axis of rotation is √((d/2)² + (d/2)²) = 3.04 m. Thus, the rotational inertia can be calculated as I = 2m(3.04)² + 2m(2.415)² = 76.8 kg·m².
In summary, the rotational inertia of this rigid body depends on the distribution of the particles and the axis of rotation. For a uniform distribution of particles, the rotational inertia can be calculated using the formula I = Σmr². For part b, where the axis of rotation passes through the midpoint of one of the sides and is perpendicular to the plane of the square, the rotational inertia is 44.2 kg·m².
For part c, where the axis of rotation lies in the plane of the square and passes through two diagonally opposite particles, the rotational inertia is 76.8 kg·m².
To know more about rotational inertia refer here
https://brainly.com/question/22513079#
#SPJ11
What kind of acceleration occurs when an object speeds up?
Ans. positive acceleration
When an object is speeding up, the acceleration is in the same direction as the velocity. Thus, this object has a positive acceleration.
A block of weight 500n is pushed up a slope by a force of 250n.assume there is no friction .calculate a.ama b.vr c.the length of the slope if the height of the slope is 10m.
a. The mechanical advantage is 2.
b. The length of the slope (input distance) is 5 meters.
a. To calculate the mechanical advantage (MA) in this scenario, we can use the formula:
MA = F_out / F_in
where F_out is the output force (the weight of the block) and F_in is the input force (the force applied to push the block).
In this case, the weight of the block is 500 N (newtons) and the force applied to push the block is 250 N.
MA = 500 N / 250 N
MA = 2
Therefore, the mechanical advantage is 2.
b. To calculate the velocity ratio (VR), we can use the formula:
VR = d_out / d_in
where d_out is the output distance (the height the block is lifted) and d_in is the input distance (the length of the slope).
In this case, the height of the slope is given as 10 m.
VR = 10 m / d_in
To find the input distance (d_in), we need to rearrange the formula:
d_in = d_out / VR
Since the mechanical advantage (MA) is equal to the velocity ratio (VR) in an ideal scenario without friction, we can substitute the MA value of 2 into the formula:
d_in = 10 m / 2
d_in = 5 m
Therefore, the length of the slope (input distance) is 5 meters.
To know more about mechanical refer here
https://brainly.com/question/20434227#
#SPJ11
discuss the key characteristics of the plot. consider the points when potential energy u is maximum, u is minimum, kinetic energy k is maximum, k is minimum and when u and k are the same value. what is the significance of these points?
In terms of physics, Potential energy (u) refers to stored energy that has the potential to be converted into kinetic energy (k), which is the energy of motion. In a story, u and k can represent the emotional energy of the characters and the events that unfold.
When u is at its maximum, it indicates that tension or conflict is building, and the story is reaching a critical point. When u is at its minimum, it suggests that the characters or situation have reached a state of equilibrium.
When k is at its maximum, it means that the story is reaching a peak in action or intensity. Conversely, when k is at its minimum, the story may be transitioning between scenes or slowing down.
When u and k are at the same value, it suggests a balance between the potential and kinetic energy, and the story may be reaching a climax or resolution.
These points are significant as they highlight important moments in the story and indicate shifts in the narrative or emotional energy of the characters. Understanding these key characteristics of the plot can help readers to engage with the story and appreciate the author's use of tension and pacing to create a compelling narrative.
To Learn More About Potential energy
https://brainly.com/question/1242059
SPJ11
6 points
A van traveling with constant velocity of 15 m-s1 passes a pedestrian crossing zone, where the speed limit is 10. M-5-1. Just as the van passes, a JMPD police
officer on a motorcycle stopped at the crossing starts off in pursuit with constant acceleration of 3. 0 m. 5-2
Save Answer
(a) How much time elapses before the officer catches up with the van? (2 marks)
(b) What is the officer's speed at that point? (2 marks)
(c) What is the total distance each vehicle has traveled at that point? (2 marks)
The total distance traveled by the van is 75 meters and the total distance traveled by the police officer is 37.5 meters at the point of catching up with the van.
What is Velocity?
Velocity is a physical quantity that describes the rate at which an object changes its position with respect to time. It is a vector quantity, which means it has both magnitude and direction. The magnitude of velocity is the speed of the object, while the direction of velocity is the direction in which the object is moving.
The van's speed is greater than the speed limit, so it will maintain a constant speed of 15 m/s. The police officer starts from rest and has a constant acceleration of 3.0 m/[tex]s^{2}[/tex]. Let's denote the time it takes for the police officer to catch up to the van as t. Using the equation of motion for the police officer's velocity, we have:
[tex]v_{police[/tex] = [tex]a_{police * t[/tex]
Using the equation of motion for the van's displacement, we have:
[tex]d_van[/tex]= [tex]v_van * t[/tex]
At the point when the police officer catches up with the van, their displacements will be equal, so we can set these two equations equal to each other and solve for t:
v_[tex]v_{police * t[/tex] = [tex]d_{van[/tex]
[tex]a_{police[/tex] *[tex]t^{2}[/tex] = [tex]v_{van[/tex] * t
3.0 * t^2 = 15 * t
t = 5 seconds
Therefore, it will take the police officer 5 seconds to catch up with the van.
(b) To find the officer's speed at that point, we can use the equation of motion for the police officer's displacement:
[tex]d_{police[/tex] = (1/2) *[tex]a_{police[/tex] *
[tex]d_{police[/tex] = (1/2) * 3.0 * [tex]5^{2}[/tex]
[tex]d_{police[/tex] = 37.5 m
Using the time t = 5 seconds, we can now find the officer's speed at that point using the equation:
[tex]v_{police[/tex]= [tex]a_{police[/tex] * t
[tex]v_{police[/tex] = 3.0 * 5
[tex]v_{police[/tex] = 15 m/s
Therefore, the officer's speed at the point of catching up with the van is 15 m/s.
(c) To find the total distance each vehicle has traveled at that point, we can use the equations of motion for each vehicle:
[tex]d_{van[/tex] = [tex]v_{van[/tex] * t
[tex]d_{police[/tex] = (1/2) * [tex]a_{police[/tex] * [tex]t^{2}[/tex]
Using the time t = 5 seconds, we can substitute the values of [tex]v_{van[/tex] and [tex]a_{police[/tex]:
[tex]d_{van[/tex] = 15 * 5
[tex]d_{van[/tex]= 75 m
[tex]d_{police[/tex]= (1/2) * 3.0 *[tex]5^{2}[/tex]
[tex]d_{police[/tex]= 37.5 m
To know more about Velocity visit;
https://brainly.com/question/80295
#SPJ4
What is the speed of the wave of its frequency is 8.0 hertz?
The speed of the wave is 16 m/s. And the right option is B. 16 m/s.
What is speed?Speed is the rate of change of displacement.
To calculate the speed of the wave, we use the formula below
Formula:
v = λf....................... Equation 1Where:
v = Velocity of the waveλ = Wavelength of wavef = Frequency of the waveFrom the question,
Given:
λ = 6/3 = 2 mf = 8 HzSubstitute these values into equation 1
v = 2×8v = 16 m/sLearn more about speed here: https://brainly.com/question/24739297
#SPJ1
How much work is done on a 80 n crate that you can carry horizontally across 2m room?
1) 1 j because horizontal
2) 2 j because horizontal
3) 0 j because horizontal
4) none of those
The correct answer is option 3)0 j.
Assuming that the crate is being carried at a constant velocity across the 2m room, the net work done on the crate is zero joules. This is because carrying a crate horizontally does not involve any work being done on the crate. Work is only done when a force is applied to an object and the object moves in the direction of the force. In this case, the crate is not moving vertically or horizontally, so no work is being done on it.
In other words, the force that you apply on the crate is in the horizontal direction, while the displacement of the crate is in the vertical direction. Therefore, the work done by the force is zero, and the net work done on the crate is also zero joules.
To know more about work, click here;
https://brainly.com/question/29762840
#SPJ11
Doug places a toy car at the top of the first hill and releases it. The car stops at point X. Which change to the model would allow the toy car to travel over all three hills?
A. Add a loop after the tallest hill in order to maximize the kinetic energy of the car.
B. Order the three hills from shortest to tallest so that the potential energy builds up according to the height of each hill.
C. Order the three hills from tallest to shortest to provide the potential energy needed for the car to make it over each hill
Adding a loop after the tallest hill in order to maximize the kinetic energy of the car change to the model would allow the toy car to travel over all three hills. Therefore, the correct answer is option A.
The toy car stopping at point X indicates that it lacks sufficient energy to overcome the potential energy barriers of the subsequent hills. In order to allow the toy car to travel over all three hills, we need to provide it with more kinetic energy.
Therefore, adding a loop after the tallest hill could provide the car with enough kinetic energy to overcome the subsequent hills. Option B, which orders the hills from shortest to tallest, would not provide the car with enough potential energy to overcome the tallest hill, let alone the subsequent hills.
On the other hand, option C, which orders the hills from tallest to shortest, would provide too much potential energy to the car at the beginning, resulting in the car overshooting the first hill and losing energy in the process.
In conclusion, adding a loop after the tallest hill would be the most appropriate change to the model to allow the toy car to travel over all three hills. Therefore, the correct answer is option A.
To know more about kinetic energy refer here:
https://brainly.com/question/7674744#
#SPJ11
When removing a wool sweater, a static discharge of 6. 43 µC dissipates 5. 72 10-3 J of energy. What voltage was involved?
The voltage involved in the static discharge is 2.98 kV (kilovolts).
The voltage involved in a static discharge can be determined using the equation:
V = √(2E/q)
where V is the voltage, E is the energy dissipated, and q is the charge involved in the discharge.
Substituting the given values, we get:
V = √(2 * 5.72 x [tex]10^{-3[/tex]J / 6.43 x [tex]10^{-6[/tex] C)
V = √(8.889 J/C)
V = 2.98 x [tex]10^3[/tex] V
It's worth noting that static electricity is a common phenomenon that occurs when two objects with different electrical charges come into contact and then separate.
The friction between the objects can cause electrons to transfer from one object to the other, resulting in a buildup of charge.
When the charge buildup becomes large enough, a static discharge can occur, which can be seen as a spark or shock.
Understanding the properties and behavior of static electricity is important in many areas of science and technology, from materials science and electronics to meteorology and environmental science.
To know more about static discharge refer here
https://brainly.com/question/30525800#
#SPJ11
A Calculate the young Young's modulus in the
calculate the Young’s modulus cantilever depression method. The length is Im.
which is suspended with a load of 150gm. The
depression is found to be 4cm. The thickness of the
beam is 5mm and breadth is 3cm (take gravity =9. 8)
Young's modulus using the cantilever depression method, we need to use the formula:
Y = (4FL^3) / (3bh^3d)
where Y is the Young's modulus, F is the force applied, L is the length of the cantilever, b is the breadth, h is the thickness, and d is the depression.
In this case, the length of the cantilever is given as 1m or 100cm, and the load applied is 150gm or 0.15kg. The depression is given as 4cm, and the breadth and thickness of the beam are given as 3cm and 5mm, respectively.
We need to convert the thickness to cm, which gives us 0.5cm.
Substituting these values in the formula, we get:
Y = (4 x 0.15 x 100^3) / (3 x 3 x 0.5^3 x 4)
Simplifying this, we get:
Y = 4.5 x 10^5 N/cm^2
Therefore, the Young's modulus of the beam is 4.5 x 10^5 N/cm^2.
It's important to note that when using the cantilever depression method, it's crucial to ensure that the beam is loaded within its elastic limit, and the deflection or depression is small enough to be considered as a linear relationship between the force applied and the deflection.
Additionally, it's important to take into account any sources of error, such as friction or air resistance, that may affect the accuracy of the results.
To know more about Young's modulus refer here
https://brainly.com/question/30756002#
#SPJ11
Starting with H = U + PV show that for an ideal gas,Cp = Cv + Nk. (This relies On the fact that H and U are independent of pressure and volume so dH /dT (dH/dT)p and dU /dT = (dU/dT)v )
For an ideal gas, Cp = Cv + Nk starting with H = U + PV and using the fact that H and U are independent of pressure and volume.
Starting with H = U + PV, we can take the partial derivative of both sides with respect to temperature (keeping pressure constant) to get:
dH/dT = dU/dT + P(dV/dT)
But for an ideal gas, we know that P(dV/dT) = Nk, where N is the number of molecules and k is Boltzmann's constant. This is because an ideal gas follows the ideal gas law PV = NkT, which can be rearranged to P = Nk/V and then differentiated with respect to temperature to get P(dV/dT) = Nk.
So substituting this in, we get:
dH/dT = dU/dT + Nk
Now, we also know that for an ideal gas, U only depends on temperature (not pressure or volume), so dU/dT = (dU/dT)v. Similarly, H only depends on temperature and pressure (not volume), so dH/dT = (dH/dT)p.
Therefore, we can rewrite the equation as:
(dH/dT)p = (dU/dT)v + Nk
And using the definition of heat capacity at constant pressure (Cp) and constant volume (Cv), we have:
Cp = (dH/dT)p and Cv = (dU/dT)v
So we can write:
Cp = Cv + Nk
Learn more about ideal gas here:-
https://brainly.com/question/28257995
#SPJ11
If there is straight line on speed time graph, which of the following statements best describes A)the body is travelling at a constant speed. B) the body is slowing down. C)the body is accelerating. D) the body is stopped
Answer:
Option A
Explanation:
If the graph plotted against Distance and Time and the graph is a linear straight line then the body is IN CONSTANT VELOCITY.And Acceleration is 0
A 2000-kg ferris wheel accelerates from rest to an angular speed of 20 rad/s in 12 s. approximate the ferris wheel as a circular disk with a radius of 30 m. what is the net torque on the wheel
The net torque on the Ferris wheel is approximately 1,500,000 N*m.
To find the net torque on the Ferris wheel, we'll need to use the following formula: τ = I * α, where τ represents torque, I is the moment of inertia, and α is the angular acceleration.
First, we need to find the angular acceleration (α). Since the Ferris wheel accelerates from rest (initial angular speed = 0) to an angular speed of 20 rad/s in 12 s, we can use the formula: α = (final angular speed - initial angular speed) / time.
α = (20 rad/s - 0 rad/s) / 12 s = 20/12 rad/s² = 5/3 rad/s²
Next, we'll find the moment of inertia (I) for a circular disk with a mass (m) of 2000 kg and a radius (r) of 30 m: I = (1/2) * m * r².
I = (1/2) * 2000 kg * (30 m)² = 1000 kg * 900 m² = 900,000 kg*m²
Now, we can find the net torque (τ) using the formula: τ = I * α.
τ = 900,000 kg*m² * 5/3 rad/s² ≈ 1,500,000 N*m
So, the net torque on the Ferris wheel is approximately 1,500,000 N*m.
To learn more about inertia, refer below:
https://brainly.com/question/3268780
#SPJ11
Please help me
how do elliptical galaxies typically compare to spiral galaxies?
a. elliptical are redder and rounder
b. elliptical are always much smaller
c. elliptical are bluer and flattened
d. elliptical are blue and rounded
e. elliptical galaxies are redder and flattened
Elliptical are redder and rounder than spiral galaxies. Option a is correct.
Elliptical galaxies are redder and rounder than spiral galaxies. Elliptical galaxies are so named because they have a shape that ranges from nearly spherical to highly elongated. They are generally redder than spiral galaxies, as they contain an older population of stars that are cooler and emit less blue light.
Spiral galaxies, on the other hand, are typically bluer due to their younger, hotter stars that emit more blue light. Elliptical galaxies also lack the distinctive spiral arms and central bulge of spiral galaxies, making them appear rounder in shape. The correct answer is (a).
To know more about galaxies, here
brainly.com/question/31361315
#SPJ4
how does the epa calculator determine co2 for gas VS electric cars?
Answer:
The Greenhouse Gas Equivalencies calculator allows you to convert emissions or energy data to the equivalent amount of carbon dioxide (CO2) emissions from using that amount. The calculator helps you translate abstract measurements into concrete terms you can understand, such as the annual emissions from cars, households, or power plants. This calculator may be useful in communicating your greenhouse gas reduction strategy, reduction targets, or other initiatives aimed at reducing greenhouse gas emissions.
Explanation:
The Greenhouse Gas Equivalencies calculator allows you to convert emissions or energy data to the equivalent amount of carbon dioxide (CO2) emissions from using that amount. The calculator helps you translate abstract measurements into concrete terms you can understand, such as the annual emissions from cars, households, or power plants. This calculator may be useful in communicating your greenhouse gas reduction strategy, reduction targets, or other initiatives aimed at reducing greenhouse gas emissions.
Angle axc is 180°. if angle axb is 132º, what is the measure of angle bxc?
The measure of angle BXC is 48°.
To find the measure of angle BXC. Let's elaborate on the process.
In the given scenario, we have angle AXB measuring 132° and angle AXC measuring 180°. To find the measure of angle BXC, we subtract the measure of angle AXB from angle AXC.
angle BXC = angle AXC - angle AXB
Substituting the given measures, we have:
angle BXC = 180° - 132°
Now, performing the subtraction:
angle BXC = 48°
Therefore, the measure of angle BXC is 48°.
This method relies on the fact that the sum of the angles in a triangle is always 180°. Since angle AXC is a straight angle (measuring 180°) and angle AXB is a known angle (measuring 132°), subtracting angle AXB from angle AXC gives us the measure of angle BXC.
By using this subtraction, we determine that angle BXC measures 48°.
It's important to remember that angle measures can be added or subtracted to find unknown angles or relationships between angles. In this case, subtracting the known angle AXB from the known angle AXC allowed us to find the measure of angle BXC.
To learn more about angle, refer below:
https://brainly.com/question/28451077
#SPJ11
What advice would you give to the company that wants to build a bridge in south america? make sure to include whether there is anything the company should change about its design and materials. give specific examples. your answer should include at least five complete sentences. (this is about earthquakes) will make brainlest and 20 points
For a company looking to build a bridge in South America, it is crucial to consider the region's seismic activity.
To ensure the bridge's safety and durability, I recommend using earthquake-resistant design features, such as base isolation or energy dissipation devices.
It's also important to choose materials with high ductility, like steel or reinforced concrete, which can better withstand the stress from earthquakes.
Additionally, the company should collaborate with local experts and authorities to understand the seismic history and geological conditions of the specific location. Lastly, it is essential to conduct regular maintenance and inspections to ensure the bridge's structural integrity over time.
To learn more about seismic, refer below:
https://brainly.com/question/13725277
#SPJ11
A force that exists between any two objects that have mass
A force that exists between any two objects that have mass: gravity. The correct option is C.
Gravity is a natural force that attracts two objects with mass towards each other. It is the reason why objects fall to the ground when dropped, and it is also responsible for keeping planets and other celestial bodies in their orbits.
The other terms, motion (A), velocity (B), and friction (D), are related to the movement and interaction of objects, but they are not the specific force that exists between objects with mass. Remember, gravity is the force that exists between any two objects that have mass. The correct option is C.
To know more about gravity, refer here:
https://brainly.com/question/14874038#
#SPJ11
Complete question:
A force that exists between any two objects that have mass:
A. motion
B. velocity
C. gravity
D. friction
Choose which has more gravitational energy
odiver with a mass of 450 n diving from a height of 20 feet
diver has a mass of 400 n standing at a height of 20 feet
diver with a mass of 450 n standing at a height of 20 feet
Based on the given information, the diver with a mass of 450 N standing at a height of 20 feet has more gravitational potential energy.
Gravitational potential energy can be calculated using the formula: PE = mgh, where PE represents potential energy, m is the mass of the object, g is the acceleration due to gravity, and h is the height above a reference point.
In this case, the diver with a mass of 450 N at a height of 20 feet has a greater mass, resulting in a higher gravitational potential energy compared to the diver with a mass of 400 N at the same height.
To learn more about mass, refer below:
https://brainly.com/question/19694949
#SPJ11
