Hi! Your question is regarding the minimum dimension for a patch-plate when a lap patch is installed on a tank bottom and the patch plate crosses a tank bottom weld. The correct answer is:
D) 12"
So, the minimum dimension for this patch-plate is 12 inches.
Learn more about minimum dimension: https://brainly.com/question/24571594
#SPJ11
Does the emergency blow down release gear uplocks
In a normal pressure vessel or pipeline, the emergency blowdown system is intended to quickly depressurize the system in the case of an emergency, like a fire or vessel breach. The blowdown system often entails the opening of valves that enable the vessel's contents to be quickly expelled to a secure area, like a flare stack or an enclosed vessel.
The release gear's uplocks have no bearing on how the emergency collapse system functions. The uplocks are often a mechanical device used to lock the release gear and stop it from mistakenly opening while it is functioning normally.
Learn more about Gears, here:
https://brainly.com/question/28733698
#SPJ4
It has been observed that cast metal parts produced using low pouring temperatures (pouring
temperature closer to the melting point of the metals) form finer grains compared to high pouring
temperatures. Explain why.
About cast metal parts, temperatures, and grains.
The reason cast metal parts produced using low pouring temperatures form finer grains compared to high pouring temperatures is due to the difference in cooling rates.
When the pouring temperature is closer to the melting point of the metal, the cooling rate is faster. This rapid cooling causes the formation of a greater number of nucleation sites, where grains begin to form. As a result, the grains have less time to grow, leading to the formation of finer grains.
On the other hand, when the pouring temperature is higher, the cooling rate is slower. This allows the grains more time to grow, resulting in larger grains.
In summary, cast metal parts produced using low pouring temperatures form finer grains compared to high pouring temperatures because the faster cooling rate leads to more nucleation sites and less time for grain growth.
To know more about pouring temperatures
https://brainly.com/question/31426024?
#SPJ11
5. Which is the better extinguisher to use for a mattress fire?
The best type of fire extinguisher to use on a mattress fire is a Class B extinguisher.
What is a class B extinguisher?
Class B extinguishers are designed to extinguish fires caused by flammable liquids and gases, such as gasoline, oil, and propane, which can also include the polyurethane foam often found in mattresses.
It's important to note that using water or a Class A extinguisher on a mattress fire can actually make the fire worse, as water can spread the flames and a Class A extinguisher is not designed to extinguish fires caused by flammable liquids or gases.
Additionally, in the event of a fire, it's important to prioritize your safety and evacuate the area immediately if the fire cannot be contained quickly and safely.
Learn more about class B extinguisher, here:
https://brainly.com/question/30040658
#SPJ4
How does VDI work as a mobile deployment model?
Virtual Desktop Infrastructure (VDI) functions as a mobile deployment model by allowing users to access their virtual desktops from any mobile device, such as smartphones or tablets. Here's a step-by-step explanation of the process:
1. VDI is set up on a central server, where virtual desktops are created and stored. These desktops contain the operating system, applications, and user data.
2. Users connect to the VDI environment via their mobile devices using a remote desktop client application or a web browser.
3. The mobile device sends input commands (such as keyboard strokes or touch gestures) to the virtual desktop on the server.
4. The server processes these commands and updates the virtual desktop accordingly.
5. The server sends the updated screen images back to the mobile device, which displays them to the user.
6. This process repeats continuously, creating an interactive experience that allows users to work on their virtual desktops from their mobile devices.
In summary, VDI works as a mobile deployment model by hosting virtual desktops on a central server and allowing users to access and interact with them from their mobile devices, providing a flexible and secure workspace solution.
To know more about Virtual Desktop Infrastructure (VDI)
https://brainly.com/question/31146030?
#SPJ11
Where are Double-Tee precast concrete usually found?
A Double Tee is a pre-stressed concrete product used for parking structures, roofs and floors, where long spans are required and/or heavy loads must be supported. They are manufactured in a protected shelter which provides controlled curing. Double tees can be installed quickly to cover large areas in a single day.
Double-Tee precast concrete is usually found in structures such as parking garages, industrial buildings, and commercial buildings. These components provide a strong, durable, and versatile solution for creating large open spaces with minimal support columns.
Double tee slabs are usually employed in construction because they shorten construction time. reduce congestion at the construction site, and also reduce construction cost.
To know more about Double-Tee precast
https://brainly.com/question/16860555?
#SPJ11
If a crystalline solid has a different electrical conductivity in the [100] and [111] directions, it is said to be:
If a crystalline solid has a different electrical conductivity in the [100] and [111] directions, it is said to exhibit anisotropic electrical conductivity. Anisotropy refers.
to the property of a material exhibiting different physical or mechanical properties in different crystallographic directions. In this case, the electrical conductivity, which is a measure of a material's ability to conduct electric current, is found to be different along the [100] and [111] directions in the crystalline solid. This can occur due to differences in the crystal structure, electron mobility, or other factors that influence the electrical conductivity of the material in different directions.
learn more about crystalline here:
https://brainly.com/question/28274778
#SPJ11
Fire Wardens who discover a fire on their floor must:
A. determine that an alarm has been transmitted
B. search and rescue all floor occupants
C. report immediately to firefighter on floor below fire
D. report in person to the Fire Command Station
Fire Wardens who discover a fire on their floor must report immediately to the Fire Command Station. Thus, its D.
The Fire Command Station is the designated location where the Fire Safety Director, Deputy Fire Safety Directors, and other designated staff can monitor fire alarm and other fire protection systems and make critical decisions about the management of a fire emergency.
The Fire Warden's primary responsibility in the event of a fire emergency is to alert the occupants on their floor of the danger and assist in their safe evacuation, following the building's Emergency Action Plan (EAP).
While searching and rescuing floor occupants is a noble and important action, it is not necessarily the primary responsibility of the Fire Wardens in the event of a fire.
Learn more about Fire Command Station, here
https://brainly.com/question/29582139
#SPJ4
A "dogbone" specimen configuration is typically used for compression tests. True or false?
False. A "dogbone" specimen configuration is typically used for tension (or "pulling") tests, not compression tests. In tension tests, the specimen is subjected to an axial load that causes it to elongate, .
the mechanical properties, such as yield strength, ultimate tensile strength, and elongation, are measured. On the other hand, in compression tests, the specimen is subjected to an axial load that causes it to shorten, and the mechanical properties, such as compressive strength and modulus of elasticity, are measured. The specimen configuration used in compression tests is typically different from the "dogbone" shape used in tension tests.
learn more about dogbone here:
https://brainly.com/question/30560332
#SPJ11
What alt are crew masks approved for
Crew masks are approved for use in high-altitude environments.
Crew masks are designed to provide breathable air to pilots and crew members in high altitude environments, such as during flights at cruising altitude. These masks are typically equipped with oxygen tanks or oxygen generators to ensure that crew members have a continuous supply of oxygen, which is necessary at high altitudes where the air pressure and oxygen levels are lower.
Crew masks are regulated by aviation authorities such as the Federal Aviation Administration (FAA) and are subject to rigorous testing and certification processes to ensure their safety and effectiveness. The specific altitude range for which crew masks are approved may vary depending on the type of mask and its intended use. However, in general, crew masks are designed to operate at altitudes up to 40,000 feet above sea level.
You can learn more about masks at
https://brainly.com/question/28178308
#SPJ11
a uniform rope of cross-sectional area breaks when the tensile stress in it reaches (a) what is the maximum load that can be lifted slowly at a constant speed by the rope? (b) what is the maximum load that can be lifted by the rope with an acceleration of
Maximum load that can be lifted slowly at a constant speed by the rope is 522.5 N
Maximum load that can be lifted by the rope with an acceleration of 5 m/s2 = 346.03 N
How to calculate the valueGravitational acceleration = g = 9.81 m/s2
Cross sectional area of the rope = A = 0.95 cm2 = 0.95 x 10-4 m2
Maximum tensile stress of the rope = \sigma = 5.5 x 106 N/m2
Tension in the rope = T
T = \sigmaA
T = (5.5x106)(0.95x10-4)
T = 522.5 N
Maximum load that can be lifted slowly at constant speed = Wa
The load is being lifted at constant speed therefore there is no acceleration, hence the forces are balanced.
T = Wa
Wa = 522.5 N
Maximum load that can be lifted with an acceleration of 5 m/s2 = Wb
Acceleration of the load = a = 5 m/s2
Mass of the load = Wb/g
(Wb/g)a = T - Wb
(Wb/9.81)(5) = 522.5 - Wb
1.51Wb = 522.5
Wb = 346.03 N
a) Maximum load that can be lifted slowly at a constant speed by the rope = 522.5 N
b) Maximum load that can be lifted by the rope with an acceleration of 5 m/s2 = 346.03 N
Learn more about speed on
https://brainly.com/question/13943409
#SPJ4
is likely to cause you to trip and fall.?
O a) Remaining alert and attentive while walking
Ob) Your foot striking an object in an unexpected way
c) Wearing the proper protective equipment
Consider the basic flat rolling process where a certain thickness reduction is required. Propose
two process modifications that would lead to the same thickness reduction with lower forces on
the rolls. Explain how these modifications lead to reduced forces.
There are two modifications that can be made to the basic flat rolling process to achieve the same thickness reduction with lower forces on the rolls.
The first modification is to increase the temperature of the material being rolled. This is because increasing the temperature of the material will make it more malleable and easier to deform, reducing the amount of force required to achieve the desired thickness reduction. This process is known as hot rolling, and it is commonly used in the production of steel and other metals.
The second modification is to introduce a pre-rolling process before the material enters the main rolling mill. This pre-rolling process involves reducing the thickness of the material in smaller increments, which allows for a more gradual reduction in thickness and a corresponding reduction in the forces required to achieve the final thickness reduction. This process is known as multi-pass rolling, and it is commonly used in the production of sheet metal.
Both of these modifications lead to reduced forces by making the material easier to deform and reducing the amount of force required to achieve the desired thickness reduction. By reducing the forces required, the wear and tear on the rolls is also reduced, resulting in lower maintenance costs and longer roll life.
To know more about thickness reduction
https://brainly.com/question/26158827?
#SPJ11
The welder must follow which variables on the WPS?
A) only the non-essential variables
B) only the essential variables
C) Both the essential & non-essential variables
D) None of the variables.
Question: "The welder must follow which variables on the WPS?"
Hi! The welder must follow which variables on the WPS? The correct answer is:
C) Both the essential & non-essential variables
Learn more about WPS variables: https://brainly.com/question/29731491
#SPJ11
Integrated Memory Controller is in the CPU (not the motherboard chip) to optimize the flow of information into and out of the CPU.
An integrated memory controller is a component found within the CPU rather than on the motherboard. Its purpose is to optimize the flow of information into and out of the CPU by directly managing the communication between the CPU and the memory. This integration leads to faster data transfers and improved performance overall.
Yes, that is correct. The Integrated Memory Controller is a component that is integrated into the CPU itself rather than being a separate chip on the motherboard.
Its purpose is to optimize the flow of information into and out of the CPU by managing the communication between the CPU and the memory. This can help improve the overall performance and speed of the system, as it allows for faster access to the data stored in memory. By having the memory controller integrated into the CPU, it also reduces latency and power consumption compared to having a separate chip on the motherboard.
to know more about memory controllers:
https://brainly.com/question/13315534
#SPJ11
5. a bucket full of water has two holes of equal size in it: a and b. which statement about the flow rate through the holes is true?
The appropriate answer is The flow through A is the same as the flow through B. Option B
Why is the through A same as the flow through B?Since that holes A and B are the same size as shown in the diagram and are situated at the lower end of the container on the right side of the diagram, they most likely are the same height. If both holes are the same size in this situation, the flow rate through them will be the same.
The above answer is based on the full question below;
a bucket full of water has two holes of equal size in it: a and b. which statement about the flow rate through the holes is true?
a. the flow through A is more then the flow through B
b. The flow through A is the same as the flow through B
c. The flow through A is less than the flow through B
Find more exercise on flow through or rate;
https://brainly.com/question/3306422
#SPJ4
All of the following will recall designated elevator cars EXCEPT:
A. #1620 key at the selected elevator bank
B. Manual station on all floors
C. Any elevator lobby smoke detector
D. Sprinkler water flow alarm test valve
The term you want to include in the answer is "elevator recall."
All of the following will recall designated elevator cars EXCEPT:
A. #1620 key at the selected elevator bank
B. Manual station on all floors
C. Any elevator lobby smoke detector
D. Sprinkler water flow alarm test valve
D. Sprinkler water flow alarm test valve
The sprinkler water flow alarm test valve is not used for elevator recall. The other options (A, B, and C) are all methods that can be used to recall designated elevator cars.
To know more about sprinkler water
https://brainly.com/question/29758654?
#SPJ11
2. If an existing office building is fully sprinklered, what is the maximum size of the office area?
The maximum size of an office area in a fully sprinklered existing office building, we need to consider the relevant building code or fire safety regulations for your specific location. These regulations can vary depending on the country, state, or municipality.
In general, having a fully sprinklered office building can allow for a larger office area as it provides better fire protection. However, to provide an accurate answer, please refer to your local building code or consult with a building professional to determine the maximum allowable office area for a fully sprinklered building in your area.
To know more about sprinklered
https://brainly.com/question/1235148
#SPJ11
True or false? A maliciously designed USB battery charger could be used to exploit a mobile device on connection.
True
A maliciously designed USB battery charger could be used to exploit a mobile device on connection. When you connect your mobile device to a compromised USB charger, it may introduce malware or execute unauthorized commands, compromising the security and data of your device. It is important to use trusted and secure USB chargers to protect your mobile device from such threats.
To know more about USB battery charger
https://brainly.com/question/12881832?
#SPJ11
When determining action during emergencies, Fire Wardens must consider all of the following EXCEPT:
A. evacuating floor for an alarm
B. waiting for instructions
C. avoiding attack stairs
D. Using smoke-free stairs
The option that is not relevant in this scenario is: B. Waiting for instructions, when determining action during emergencies.
Fire Wardens are trained to take immediate action to evacuate occupants in the event of an emergency, and waiting for instructions may cause a delay in the response and potentially endanger occupants.
Instead, Fire Wardens should take initiative and follow the Emergency Action Plan to evacuate occupants safely and quickly. However, Fire Wardens should also maintain communication with the Fire Safety Director and other designated personnel to provide updates and receive additional instructions as needed.
Learn more about fire emergencies, here
https://brainly.com/question/17257100
#SPJ4
what data-structures linker will use and what will be the values of all the variables and data-structures at the end of pass 1 of linkage editor?
A linker can use any of the following data structures during pass 1 of its operation:
Symbol table - a data structure that stores information about symbols defined and referenced in the object files and may contain entries for functions, variables, etc, with their associated addresses and attributes.
A relocation table is a data structure that stores information about the locations in the object files that need to be modified during the linking process. It contains and specifies the type of relocation and the associated symbol.
The linker may use data structures to represent the object files that are being processed, such as a format-specific data structure like ELF, or COFF that stores the object file's sections, symbols, and other attributes.
During pass 1, the linker may also use Loader Data Structures that represent the layout and organization of the target system's memory, such as segments or sections that will be used to load the executable program or shared library.
The actual values of these variables and data structures will depend on the specific input files being processed and the linker's implementation.
What does a linker do?A linker is in charge of resolving symbols (such as function or variable names) in object files and libraries and generating an executable program or shared library.
Read more about a linker at brainly.com/question/30329219
#SPJ4
Inspection hold points, for tank reconstruction, shall be designated by:
A) The authorized inspector
B) An engineer experienced in storage tank design
C) Agreement between tank owner/user and reconstruction contractor
D) Agreement between and engineer and the authorized
The inspection hold points for tank reconstruction shall be designated by the authorized inspector that is in Option A, as tank reconstruction involves various activities such as demolition, reconstruction, and welding.
The authorized inspector is a qualified individual who is responsible for ensuring that the reconstruction work meets the relevant industry standards and regulations. The inspector is typically employed by the tank owner, the reconstruction contractor, or a third-party inspection agency. The inspector must have the appropriate qualifications and experience to carry out the inspections and ensure that the reconstruction work is completed in a safe and reliable manner.
Thus, option A is correct answer.
Learn more about the engineer here.
https://brainly.com/question/17858199
#SPJ4
Where can small holes not but cut from in cast-in-place concrete floors?
Small holes cannot be cut in certain areas of cast-in-place concrete floors, such as those that are reinforced with rebar or post-tensioned cables. These areas are critical to the structural integrity of the concrete, and cutting into them can compromise the strength and stability of the floor.
What are concrete floors?
Concrete floors are a type of flooring material that is made from a mixture of cement, water, and aggregates (such as sand, gravel, or crushed stone). The mixture is poured onto a surface and then smoothed and leveled, typically using a trowel or power screed. Once the concrete has hardened and cured, it forms a strong and durable flooring surface that can be used in a variety of applications.
Concrete floors are commonly used in industrial, commercial, and residential settings. They are popular in industrial and commercial settings because they are durable and resistant to heavy traffic, abrasion, and chemicals. In residential settings, concrete floors are often used in basements, garages, and outdoor spaces because they are affordable, low-maintenance, and can be finished in a variety of ways to create a decorative surface.
It is important to consult with a structural engineer or experienced contractor before cutting into any concrete floor to ensure that it is done safely and without damaging the structure.
to know more about concrete floors:
https://brainly.com/question/29152455
#SPJ11
Can the Java compiler be accessed from the Command Prompt?
Yes, the Java compiler can be accessed from the Command Prompt.
To compile a Java program, you need to navigate to the directory containing the Java file using the Command Prompt and then run the command "javac .java". This will compile the Java file and create a corresponding .class file in the same directory. You can then run the compiled Java program using the command "java ".
Learn more about Command Prompt: https://brainly.com/question/25808182
#SPJ11
Data analysis provides you with the ability to be _____, which is important to advance cloud security.reactive and resilientactive and elasticredundant and secureproactive and predictive
The term that best fits the blank in the question is "proactive and predictive".
Data analysis enables organizations to be proactive in identifying potential security threats before they occur, as well as predictive in anticipating potential issues before they can do damage to the cloud environment. This is important for advancing cloud security, as it allows for quick action to be taken to prevent security breaches and other issues.
By being proactive and predictive, organizations can stay ahead of the curve and ensure that their cloud security is as robust and secure as possible. It can be said that data analysis is essential for advancing cloud security as it helps organizations to be proactive and predictive in identifying and addressing potential security threats. This enables them to stay ahead of the curve and ensure that their cloud environments remain secure and resilient.
Learn more about Data analysis: https://brainly.com/question/30156066
#SPJ11
9. Identify the well-known port number for NTP.
a. 53
b. 69
c. 123
d. 143
The well-known port number for NTP (Network Time Protocol) is 123. NTP is a protocol used for time synchronization on networks. It allows computer systems to synchronize their clocks with a reference time source. The reference time source can be a GPS receiver, a radio clock, or an Internet time server.
For such more question on communicate
https://brainly.com/question/28153246
#SPJ11
True or false? The following string is an example of a distinguished name: CN=ad, DC=classroom, DC=com.
True. The given string is an example of a distinguished name, which is used to uniquely identify an object or entry in a directory service such as Active Directory.
The CN (common name) attribute represents the name of the object, while the DC (domain component) attributes represent the domain name components in a hierarchical order. In this case, the distinguished name represents an object named "ad" in the "classroom.com" domain.
to know more about strings:
https://brainly.com/question/30099412
#SPJ11
What mathematical formalism underlies functional programming?
Functional programming is built on mathematical concepts such as lambda calculus and category theory. Lambda calculus is a formal system that describes functions and their application. Category theory is a branch of mathematics that studies the structure of mathematical objects and the relationships between them. Functional programming uses these concepts to define functions as mathematical objects and manipulate them through operations such as composition and recursion. This mathematical formalism provides a foundation for the development of functional programming languages and the creation of programs that are concise, modular, and easy to reason about.
Learn more about Functional programming: https://brainly.com/question/22654163
#SPJ11
Where is Beam-and-Girder construction typically found?
Beam-and-Girder construction is a common type of construction used in building structures such as commercial buildings, residential homes, and bridges. It involves the use of horizontal beams and vertical columns (girders) to support the weight of the building or structure. This type of construction is commonly found in high-rise buildings and other large structures that require a strong and stable framework.
In the construction of bridges, residential residences, and office buildings, beam-and-girder construction is frequently utilised.
To sustain the weight of the building or structure, horizontal beams and vertical columns (girders) are used in the construction.
A grid-like design is often created by placing the beams and girders in a sequence of parallel lines, which equally distributes the weight.
This style of building is frequently used in high-rise projects and other sizable buildings that need for a solid and secure framework.
Because the beams and girders can be positioned widely to accommodate various room sizes and forms, the beam-and-girder building system offers versatility in terms of design and layout.
A long-lasting, damage- and wear- and-tear-resistant construction technique is beam-and-girder construction.
Learn more about Beam-and-Girder:
https://brainly.com/question/18126205
#SPJ11
_____ is an application that you rent over the open internet.IaaSSaaSPaaSTaaS
Software as a Service (SaaS) is an application that you rent over the open internet.
The answer to your question is that the term that describes an application that you rent over the open internet is "IaaS" (Infrastructure as a Service), "SaaS" (Software as a Service), "PaaS" (Platform as a Service), or "TaaS" (Testing as a Service). These are all examples of cloud computing services that allow users to access applications and resources over the internet without needing to own and maintain the underlying infrastructure themselves.
Learn more about IaaS here :
https://brainly.com/question/29515229
#SPJ11
What must be true for technology to be usable?
For technology to be usable, it must be accessible, user-friendly, functional, and reliable. This ensures that users can easily interact with the technology and achieve their desired outcomes while experiencing minimal issues or difficulties.
For technology to be usable, it must meet the needs and expectations of the user, be accessible and easy to use, and perform its intended functions reliably and efficiently. Additionally, the technology must be compatible with the user's devices and operating systems, be secure and protect user data, and be regularly updated and maintained. User training and support may also be necessary for the technology to be effectively used. Ultimately, the technology should enhance productivity, improve communication and collaboration, and provide a positive user experience.
Learn More about technology here :-
https://brainly.com/question/9171028
#SPJ11
