An increase in potential difference (P.D.) across a thermistor leads to an: increase in current flow, which generates heat and raises the temperature of the thermistor.
A thermistor is a temperature-sensitive resistor whose resistance varies with temperature changes. When the potential difference (P.D.) across a thermistor increases, more electric current flows through it. As the electric current increases, the electrons in the thermistor gain more kinetic energy and collide more frequently with the lattice structure of the material, which generates heat.
The increased heat raises the temperature of the thermistor. In a negative temperature coefficient (NTC) thermistor, the resistance decreases as the temperature rises. This is because, as the thermistor heats up, the lattice structure of the material expands, allowing more electrons to move more freely and conduct electricity more efficiently. Consequently, the resistance decreases with an increase in temperature.
So, to summarize, an increase in potential difference (P.D.) across a thermistor leads to an increase in current flow, which generates heat and raises the temperature of the thermistor. In an NTC thermistor, this increased temperature causes a decrease in resistance due to the expansion of the lattice structure, which allows electrons to move more freely and conduct electricity more efficiently.
To know more about thermistor, refer here:
https://brainly.com/question/16729324#
#SPJ11
If the current in a circuit is 3. 2 mA and the resistance of the wire used in the circuit is 250 Ω, what is the voltage of the fuel cell being used?
Formula;
Calculation;
Answer:
If the current in a circuit is 3. 2 mA and the resistance of the wire used in the circuit is 250 Ω, the voltage of the fuel cell being used in the circuit is 0.8 volts.
To calculate the voltage of the fuel cell being used in a circuit, we can use Ohm's law, which states that the voltage (V) equals the current (I) multiplied by the resistance (R): V = I x R.
In this case, the current is 3.2 mA (milliamperes), and the resistance of the wire used in the circuit is 250 Ω (ohms). We first need to convert the current to amperes by dividing it by 1000: 3.2 mA ÷ 1000 = 0.0032 A.
Next, we can substitute these values into the formula to calculate the voltage: [tex]V = 0.0032 \;A \times 250 \;\Omega = 0.8 \;volts.[/tex]
Therefore, the voltage of the fuel cell being used in the circuit is 0.8 volts.
In summary, to calculate the voltage of a fuel cell being used in a circuit, we can use Ohm's law, which states that voltage equals current multiplied by resistance.
By converting the current from milliamperes to amperes and substituting the values into the formula, we can determine the voltage of the fuel cell in volts.
To know more about resistance refer here:
https://brainly.com/question/30155623#
#SPJ11
Find the radius of the path described by a proton moving at 175 km/s in a plane perpendicular to a 64. 6- mt magnetic field
The radius of the path described by a proton moving at 175 km/s in a plane perpendicular to a 64. 6- mt magnetic field is 0.0657 meters. When a proton moves perpendicular to a magnetic field, it experiences a magnetic force.
A proton moving perpendicular to a magnetic field will experience a magnetic force that acts as a centripetal force, causing the proton to move in a circular path.
The radius of this path can be determined using the formula r = mv/qB, where m is the mass of the proton, v is its velocity, q is its charge, and B is the strength of the magnetic field.
Substituting the values given, we have
[tex]r = (1.67 \times 10^{-27} kg)(175 \times 10^3 \;m/s)/(1.6 \times 10^{-19} C)(64.6 \times 10^{-3} T)[/tex]
r = 0.0657 m.
Therefore, the radius of the path described by the proton is 0.0657 meters.
In summary, when a proton moves perpendicular to a magnetic field, it experiences a magnetic force that causes it to move in a circular path. The radius of this path can be calculated using the formula r = mv/qB.
Given the mass, velocity, charge, and strength of the magnetic field, we can calculate the radius of the circular path, which in this case is 0.0657 meters.
To know more about magnetic field refer here:
https://brainly.com/question/30389034#
#SPJ11
As an object moves from point a to point b only two forces act on it: one force is nonconservative and does −30 j of work, the other force is conservative and does +50 j of work. between a and b,
Between point A and point B, the net work done on the object is: +20 joules, indicating that the system has gained energy overall, likely in the form of kinetic or potential energy.
As the object moves from point A to point B, it experiences both conservative and nonconservative forces. Conservative forces, such as gravity and spring forces, have the ability to store energy in the form of potential energy, and the work done by these forces can be recovered. Nonconservative forces, like friction or air resistance, dissipate energy as heat, and the work done by these forces cannot be recovered.
In this specific case, the nonconservative force does -30 joules of work, which implies that energy is being removed from the system as heat. On the other hand, the conservative force does +50 joules of work, meaning energy is being stored as potential energy in the system.
To find the net work done on the object as it moves from point A to point B, you can simply add the work done by both forces. In this case, the net work is -30 joules (nonconservative force) + 50 joules (conservative force) = +20 joules.
So, between point A and point B, the net work done on the object is +20 joules, indicating that the system has gained energy overall, likely in the form of kinetic or potential energy.
To know more about potential energy, refer here:
https://brainly.com/question/13548111#
#SPJ11
A conducting coil of 2250 turns is connected to a galvanometer, and the total resistance of the circuit is 30 ω. the area of each turn is 5. 00 × 10-4 m2. this coil is moved from a region where the magnetic field is zero into a region where it is nonzero, the normal to the coil being kept parallel to the magnetic field. the amount of charge that is inducedto flow around the circuit is measu
When a conducting coil is moved into a region with a magnetic field, an electromotive force (EMF) is induced in the coil, which causes a current to flow through the circuit.
The magnitude of the induced EMF can be calculated using Faraday's law of electromagnetic induction, which states that the induced EMF is equal to the rate of change of magnetic flux through the coil.
In this case, the coil has 2250 turns and an area of 5.00 × 10^-4 m^2 per turn. If the coil is moved into a region with a magnetic field, the magnetic flux through the coil will change, inducing an EMF in the circuit.
Assuming that the normal to the coil is parallel to the magnetic field, the magnitude of the induced EMF can be calculated as follows:
EMF = -N(dΦ/dt)
where N is the number of turns in the coil and dΦ/dt is the rate of change of magnetic flux through the coil.
The magnetic flux through the coil is given by:
Φ = BA
where B is the magnetic field strength and A is the area of the coil.
Assuming that the magnetic field is uniform and perpendicular to the coil, the magnetic flux through the coil can be written as:
Φ = BNA
The rate of change of magnetic flux through the coil is given by:
dΦ/dt = BNA(v/A) = BNV
where v is the velocity of the coil.
Substituting the values given, we get:
EMF = -2250(5.00 × 10^-4 m^2)(B)(V)/30 Ω
The negative sign indicates that the direction of the induced EMF is opposite to the change in magnetic flux.
The amount of charge that flows around the circuit can be calculated using the equation:
Q = EMF/R
where R is the total resistance of the circuit.
Substituting the values given, we get:
Q = (-2250)(5.00 × 10^-4 m^2)(B)(V)/(30 Ω)
Therefore, the amount of charge induced to flow around the circuit depends on the strength of the magnetic field, the velocity of the coil, and the resistance of the circuit.
To know more about induced EMF refer here
https://brainly.com/question/16764848#
#SPJ11
at what time of the day is the demand of electricity highest?
Answer:
morning hours
Explanation:
Estimate how the phase difference would change when the value of ω changes from zero to infinity in the circuit
Without a specific circuit provided, it is difficult to estimate how the phase difference would change when the value of ω changes from zero to infinity.
The phase difference is dependent on the specific circuit components and their respective impedances.
In general, the phase difference between voltage and current in a circuit with inductive or capacitive elements can change significantly as the frequency (or angular frequency ω) changes.
For example, in a simple series circuit consisting of a resistor and an inductor, the phase difference between the voltage and current is zero at DC (ω=0) and approaches 90 degrees as ω approaches infinity.
In contrast, for a series circuit with a resistor and capacitor, the phase difference starts at 90 degrees at DC and approaches zero as ω approaches infinity.
Therefore, it is important to analyze the specific circuit and its components to determine how the phase difference would change as ω changes from zero to infinity.
To know more about phase difference refer here
brainly.com/question/14594671#
#SPJ11
a predatory bird is chasing its prey at 15.3 m/s when it emits a 202 hz squawk. if
the prey is moving away from the predator at 13 m/s, what frequency will it hear if
the air temperature is 27 °c?
The prey will hear the predator's squawk at an approximate frequency of 219 Hz.
The Doppler effect formula for sound and consider the given information: the predator's speed (15.3 m/s), the prey's speed (13 m/s), the emitted frequency (202 Hz), and the air temperature (27 °C).
Step 1: Calculate the speed of sound in air at 27 °C. The formula is: v = 331.4 + 0.6 * T, where T is the temperature in Celsius.
v = 331.4 + 0.6 * 27 = 347.2 m/s
Step 2: Apply the Doppler effect formula for sound: f' = f * (v + vo) / (v + vs), where f' is the observed frequency, f is the emitted frequency, v is the speed of sound, vo is the speed of the observer (prey), and vs is the speed of the source (predator).
Note: Since the prey is moving away from the predator, vo is positive (13 m/s). The predator is also moving toward the prey, so vs is negative (-15.3 m/s).
Step 3: Substitute the given values into the Doppler effect formula.
f' = 202 * (347.2 + 13) / (347.2 - 15.3) = 202 * 360.2 / 331.9
Step 4: Calculate the observed frequency.
f' ≈ 219 Hz
For more about frequency:
https://brainly.com/question/14926605
#SPJ11
What is the frequency of red light, which has a wavelength of around 6. 35 * 10 ^ 7 - 7 m? (Remember: speed of light is 3*10^ 1 8 m/s) Be sure to show all work
To calculate the frequency of red light, we need to use the formula:
frequency = speed of light / wavelength
The speed of light is given as 3*10^18 m/s and the wavelength of red light is around 6.35*10^-7 m. Plugging these values into the formula, we get:
frequency = 3*10^18 / 6.35*10^-7
frequency = 4.72*10^14 Hz
Therefore, the frequency of red light is approximately 4.72*10^14 Hz.
Frequency is a measure of how many cycles of a wave occur in one second. In the case of light, it refers to how many times a light wave oscillates per second. Wavelength, on the other hand, refers to the distance between two consecutive peaks or troughs of a wave. It is related to frequency through the speed of light, which is a constant in vacuum.
In summary, the frequency of red light is determined by its wavelength and the speed of light. The calculation involves dividing the speed of light by the wavelength of the light. This calculation can be used to determine the frequency of any other type of light, provided its wavelength is known.
To know more about frequency refer here
https://brainly.com/question/5102661#
#SPJ11
Claim how it would be possible to predict the speed that a 2000 kg car full with riders will reach before it’s ever placed on the track. Cite evidence by using the appropriate formulas and reasoning by solving them in order to calculate the speed of the car at the bottom of the first hill
We can predict that the car full of riders will reach a speed of 28.0 m/s at the bottom of the first hill based on the principles of conservation of energy.
It is possible to predict the speed that a 2000 kg car full with riders will reach before it's ever placed on the track using the principles of conservation of energy. According to the law of conservation of energy, the total energy in a system remains constant, and it can be converted from one form to another.
To calculate the speed of the car at the bottom of the first hill, we can use the conservation of energy equation, which states that the initial potential energy (PEi) of the car is equal to the final kinetic energy (KEf) of the car.
PEi = KEf
[tex]mgh = 1/2mv^2[/tex]
Where m is the mass of the car, g is the acceleration due to gravity, h is the height of the hill, and v is the velocity of the car.
Solving for v, we get:
[tex]v = \sqrt{(2gh)}[/tex]
Using the given values of m = 2000 kg, h = 40 meters, and g = 9.81 m/s², we can calculate the velocity of the car at the bottom of the first hill:
[tex]v = \sqrt{(2gh)} = \sqrt{(2 \times 9.81 \;m/s^2 \times 40 m)} = 28.0 m/s[/tex]
Therefore, we can predict that the car full of riders will reach a speed of 28.0 m/s at the bottom of the first hill based on the principles of conservation of energy.
In summary, by using the conservation of energy equation, we can predict the speed of the car at the bottom of the first hill based on its mass and the height of the hill. We found that the car full of riders will reach a speed of 28.0 m/s using this method.
To know more about speed refer here:
https://brainly.com/question/28060745#
#SPJ11
When a wind-up toy is set in motion, elastic potential energy that was stored in a compressed spring is converted into the __________ of the toy’s moving parts
Answer:When a wind-up toy is set in motion, elastic potential energy that was stored in a compressed spring is converted into the kinetic energy of the toy's moving parts.
Explanation:
Researchers are trying to use radiocarbon dating to determine when the wooden buildings at an archaeological site were constructed. They know that trees in the area would have been cut down for the construction, and that when the trees died, they would have a ratio of carbon-14 to carbon-12 of about one part per trillion (1 ppt). The half-life for the decay of carbon-14 is 5,730 years, and they discover the ratio of carbon-14 to carbon-12 to be about 0. 125 parts per trillion (ppt). What is the age of the buildings at the site? *
716. 25 years
5,730 years
17,190 years
0. 125 billion years
The age of the buildings at the site is approximately 17,190 years. The correct option is 17190 years.
To determine the age of the wooden buildings using radiocarbon dating, we can use the half-life formula:
N = N₀ * (1/2)^(t/T)
where:
- N is the current ratio of carbon-14 to carbon-12 (0.125 ppt)
- N₀ is the initial ratio of carbon-14 to carbon-12 when the trees were cut down (1 ppt)
- t is the time elapsed (the age of the buildings, which we want to find)
- T is the half-life of carbon-14 (5,730 years)
We can rearrange the formula to solve for t:
t = T * log2(N₀/N)
Plugging in the given values:
t = 5730 * log2(1/0.125)
t = 5730 * log2(8)
t = 5730 * 3
t = 17,190 years
So, the correct option is 17190 years.
For more about buildings:
https://brainly.com/question/23099874
#SPJ11
An electron moves with an unknown velocity through a magnetic field of 1. 56 T that points directly east. The electron experiences a force of 6. 24 x 10-15 N directly south. What is the magnitude and direction of the velocity? Show your work. (The charge of an electron is -1. 6 x 10-19 C)
The magnitude of the velocity is 0.0246 m/s and the direction of the velocity is directly north.
The magnetic force on a charged particle is the force experienced by a moving charged particle when it interacts with a magnetic field. When a charged particle moves through a magnetic field, it experiences a force that is perpendicular to both its velocity and the magnetic field direction. This force is known as the magnetic force or the Lorentz force.
The magnitude of the magnetic force is proportional to the charge of the particle, the magnitude of its velocity, and the strength of the magnetic field. The direction of the force is perpendicular to both the velocity vector and the magnetic field vector, following the right-hand rule.
It is given by the formula:
F = qvB
Where F is the force, q is the charge, v is the velocity, and B is the magnetic field.
F = 6.24 x 10⁻¹⁵ N (force)
q = -1.6 x 10⁻¹⁹ C (charge)
B = 1.56 T (magnetic field)
v = F / (qB)
v = (6.24 x 10⁻¹⁵ N) / (-1.6 x 10⁻¹⁹ C) / (1.56 T)
v = -0.0246 m/s
Learn more about Magnetic force on Charged particle, here:
https://brainly.com/question/31789735
#SPJ12
Stade avogadro's hypothesis what are its applications, prove that hydrogen hydrogen and oxygen gases
Avogadro's hypothesis confirms that hydrogen and oxygen gases react in a 2:1 ratio to form water, as two moles of hydrogen gas react with one mole of oxygen gas to produce two moles of water vapor.
Regarding the case of hydrogen and oxygen gases, we can apply Avogadro's hypothesis to prove that they react in a 2:1 ratio to form water. According to the hypothesis, one mole of any gas contains the same number of particles, which is equal to Avogadro's number. Therefore, if we take equal volumes of hydrogen and oxygen gases at the same temperature and pressure, they will contain the same number of particles.
In the case of the reaction between hydrogen and oxygen, one mole of hydrogen gas reacts with one-half mole of oxygen gas to produce one mole of water. This reaction equation implies that two volumes of hydrogen gas react with one volume of oxygen gas to form two volumes of water vapor.
Since the gases are at the same temperature and pressure, their volumes are directly proportional to their moles. Thus, two volumes of hydrogen gas will contain twice as many particles as one volume of oxygen gas. Therefore, two moles of hydrogen gas react with one mole of oxygen gas to form two moles of water vapor.
Avogadro's hypothesis states that equal volumes of gases at the same temperature and pressure contain the same number of particles. This concept has several applications in chemistry, including in the calculation of molar volumes and molar masses of gases.
To learn more about Avogadro's hypothesis
https://brainly.com/question/20358713
#SPJ4
Complete question:
What are the applications of Avogadro's hypothesis, and how can it be used to prove the combination of hydrogen and oxygen gases?
How would an increase in the number of birds affect the number OF mice. Explain ur answer
The relationship between birds and mice is complex and can vary depending on a variety of factors such as the species of birds and mice, the availability of food and habitat, and the presence of predators.
Generally, an increase in the number of birds can have both positive and negative effects on the number of mice. On one hand, birds are predators of mice and can help to control their population by preying on them. Thus, an increase in the number of birds can lead to a decrease in the number of mice.
On the other hand, birds can also indirectly increase the number of mice by providing them with food and habitat. For example, some species of birds such as sparrows and pigeons can create a lot of waste material in their nesting areas, which can attract mice and provide them with a source of food and shelter.
In summary, the relationship between birds and mice is complex and can have both positive and negative effects on each other. An increase in the number of birds can lead to a decrease in the number of mice through predation.
But can also indirectly increase the number of mice by providing them with food and habitat. The specific effects depend on a variety of factors and can vary depending on the situation.
To know more about species refer here:
https://brainly.com/question/29912614#
#SPJ11
A 100-coil spring has a spring constant of 470 n/m. it is cut into four shorter springs, each of which has 25 coils. one end of a 25-coil spring is attached to a wall. an object of mass 35 kg is attached to the other end of the spring, and the system is set into horizontal oscillation. what is the angular frequency of the motion?
The angular frequency of the motion is ω = √(7520 N/m ÷ 35 kg) = 10.75 rad/s.
The spring constant of each of the four shorter springs is four times that of the original spring since each spring has one-fourth of the original length.
Therefore, the spring constant of each shorter spring is 4 × 470 N/m = 1880 N/m. The angular frequency of the motion, ω, is given by the equation ω = √(k/m), where k is the spring constant and m is the mass of the object.
Since the four shorter springs are attached in parallel, their combined spring constant is 4 times that of each spring, or 4 × 1880 N/m = 7520 N/m.
Thus, the angular frequency of the motion is ω = √(7520 N/m ÷ 35 kg) = 10.75 rad/s.
To know more about angular frequency, refer here:
https://brainly.com/question/30885221#
#SPJ11
2) A car travelling at 35. 0 km / hr speeds up to 45 km / hr in a time of
5. 00 s. The same car later speeds up from 65 km / hr to 75 km/hr in
a time of 5. 00 sec.
a. Calculate the magnitude of the constant acceleration for each of
these intervals.
b. Determine the distance traveled by the car during each of these
time intervals.
A car travelling at 35. 0 km / hr speeds up to 45 km/hr in a time of 5.00 s. The same car later speeds up from 65 km / hr to 75 km/hr in a time of 5. 00 sec.
a. To calculate the magnitude of acceleration, we can use the formula
a = (Vf - Vi) / t
Where a is the acceleration, Vf is the final velocity, Viis the initial velocity, and t is the time taken.
For the first interval, Vi = 35 km/hr = 9.72 m/s, Vf = 45 km/hr = 12.5 m/s, and t = 5.00 s.
So, a = (12.5 - 9.72) / 5.00 = 0.556 m/[tex]s^{2}[/tex]
For the second interval, Vi = 65 km/hr = 18.1 m/s, Vf = 75 km/hr = 20.8 m/s, and t = 5.00 s.
So, a = (20.8 - 18.1) / 5.00 = 0.540 m/[tex]s^{2}[/tex]
b. To calculate the distance traveled by the car during each time interval, we can use the formula
d =Vit + 1/2a[tex]t^{2}[/tex]
Where d is the distance traveled, vi is the initial velocity, a is the acceleration, and t is the time taken.
For the first interval, vi = 9.72 m/s, a = 0.556 m/[tex]s^{2}[/tex], and t = 5.00 s.
So, d = (9.72)(5.00) + [tex]1/2(0.556)(5)^{2}[/tex] = 66.8 m
For the second interval, vi = 18.1 m/s, a = 0.540 m/[tex]s^{2}[/tex], and t = 5.00 s.
So, d = (18.1)(5.00) + [tex]1/2 (0.540)(5)^{2}[/tex] = 128.3 m
Therefore, the distance traveled by the car during the first interval is 66.8 m, and during the second interval is 128.3 m.
To know more about speeds here
https://brainly.com/question/22109908
#SPJ4
A pumpkin was rolling down a hill that is 12. 3 miles long from top to bottom. The pumpkin achieved a final velocity of 42. 4 m/s and it took
3. 5 minutes to roll down the hill The pumpkin had a mass of 4780 grams. What momentum AND force did the pumpkin have at the
bottom of the hill?
Momentum of the pumpkin at the bottom of the hill: 960,512 kg*m/s
What is Mass?
Mass is a physical property of matter that describes the amount of matter in an object. It is a measure of the resistance an object has to changes in its motion or position due to external forces. The standard unit of mass in the International System of Units (SI) is the kilogram (kg).
To find the force exerted on the pumpkin at the bottom of the hill, we can use the formula for force, which is:
F = ma
where F is force, m is mass, and a is acceleration.
We can calculate the acceleration of the pumpkin using the formula:
a = (vf - vi) / t
where vf is final velocity, vi is initial velocity (which we assume to be 0), and t is time.
Plugging in the values we know:
a = (42.4 m/s - 0 m/s) / (3.5 minutes x 60 seconds/minute)
a = 2.02 m/[tex]s^{2}[/tex]
Now we can plug in the values for mass and acceleration to find the force:
F = (4.78 kg)(2.02 m/[tex]s^{2}[/tex])
F = 9.664 N
To know more about Mas visit;
https://brainly.com/question/86444
#SPJ4
Recommendations
skill plans
a math
language arts
ga standards
sixth grade ff 20 volume of cubes and rectangular prisms: word problems bbm
you have prizes to reveal! go to y
after visiting the needleton natural museum, irma was so fascinated by the reptile exhibit
that she got her very own pet lizard, irma bought a terrarium shaped like a rectangular prism
for her lizard to live in. the terrarium is 20 inches long, 15 inches wide, and 12 inches tall.
which equation can you use to find the volume of the terrarium, v?
20. 15 = 12v
v = 20. 15. 12
what is the volume of the terrarium?
write your answer as a whole number or decimal. do not round.
cubic inches
submit
lo my
The volume of the terrarium is approximately 4.69 cubic feet.
The volume of the terrarium, we can use the formula for the volume of a rectangular prism:
V = lwh
We know that the length of the terrarium is 20 inches, the width is 15 inches, and the height is 12 inches. Therefore, we can substitute these values into the formula:
V = 20 inches * 15 inches * 12 inches
V = 300 inches
We want the volume in cubic inches, so we can convert cubic inches to cubic feet by dividing by 63:
V = 300 inches / 63
V = 4.69 cubic feet
Therefore, the volume of the terrarium is approximately 4.69 cubic feet.
Learn more about terrarium Visit: brainly.com/question/31235057
#SPJ4
an 82-kg skater is pushed on a frictionless surface through a straight line displacement
of = (13.2m) î + (18.9m) û by a force = (182n) î + (121n) û .
how much work does the force do on the skater during this displacement?
The force does 4688.3 joules of work on the skater during this displacement.
The work done by a force on an object is defined as the product of the force and the displacement of the object in the direction of the force. In this problem, the displacement vector and the force vector are given.
To calculate the work done on the 82-kg skater during the displacement, you need to find the dot product of the force vector and the displacement vector. Here are the given vectors:
Force vector (F) = (182N) î + (121N) û
Displacement vector (d) = (13.2m) î + (18.9m) û
Work (W) = F • d = (182N * 13.2m) + (121N * 18.9m)
W = (2402.4 J) + (2285.9 J)
W = 4688.3 J
It is important to note that since the surface is frictionless, there is no loss of energy due to friction. This means that the work done by the force is equal to the change in the kinetic energy of the skater.
To know more about the displacement, click here;
https://brainly.com/question/11934397
#SPJ11
A plate falls vertically to the floor and breaks up into three pieces, which slide along the floor. Immediately after the impact, a 320-g piece moves along the x-axis with a speed of 2. 00 m/s and a 355-g piece moves along the y-axis with a speed of 1. 50 m/s. The third piece has a mass of 100 g. In what direction does the third piece move? you can neglect any horizontal forces during the crash.
The third piece moves with a velocity of 1.62 m/s in the direction opposite to 36.9 degrees from the positive x-axis.
Since the plate falls vertically to the floor, there is no initial velocity in the x or y direction.
Therefore, we can use conservation of momentum to determine the velocity of the third piece.
The total momentum of the plate before the impact is zero, since there is no initial velocity. The total momentum of the three pieces after the impact must also be zero, since there are no external forces acting on the system. Therefore, we can write:
m1v1 + m2v2 + m3v3 = 0
where m1, m2, and m3 are the masses of the three pieces, and v1, v2, and v3 are their respective velocities.
We know the masses and velocities of two of the pieces:
m1 = 320 g = 0.320 kg
v1 = 2.00 m/s
m2 = 355 g = 0.355 kg
v2 = 1.50 m/s
Substituting these values into the equation above and solving for v3, we get:
m3v3 = -(m1v1 + m2v2)
v3 = -(m1v1 + m2v2) / m3
Plugging in the values we know, we get:
v3 = -((0.320 kg)(2.00 m/s) + (0.355 kg)(1.50 m/s)) / 0.100 kg
v3 = -1.62 m/s
So the third piece moves in the opposite direction of the sum of the velocities of the other two pieces. Its velocity has a magnitude of 1.62 m/s, and it moves in the direction opposite to the vector sum of the velocities of the other two pieces. We can use the Pythagorean theorem to find the magnitude and direction of this vector:
[tex]|v| = \sqrt{(vx^2 + vy^2)}[/tex]
[tex]|v| = \sqrt{((2.00 m/s)^2 + (1.50 m/s)^2)[/tex]
|v| = 2.50 m/s
θ = atan(vy / vx)
θ = atan(1.50 m/s / 2.00 m/s)
θ = 36.9 degrees
To know more about conservation of momentum refer here
https://brainly.com/question/3920210#
#SPJ11
A 3.0-cm-tall object is 12 cm in front of a concave mirror that has a 25 cm focal length.
1 Calculate the image position.
2 Calculate the image height. Type a positive value if the image is upright and a negative value if it is inverted.
The image is located 18.75 cm behind the mirror. The image height is 4.7 cm and it is inverted.
1. The image position can be found using the mirror equation:
1/f = 1/di + 1/do
Where f is the focal length, di is the image distance, and do is the object distance. Rearranging this equation to solve for di, we get:
di = 1/(1/f - 1/do)
Plugging in the given values, we get:
di = 1/(1/25 - 1/12)
di = 18.75 cm
Therefore, the image is located 18.75 cm behind the mirror.
2. The image height can be found using the magnification equation:
m = -di/do
Where m is the magnification. Since the image distance is negative (meaning it is behind the mirror), the magnification will also be negative, indicating an inverted image. Plugging in the given values, we get:
m = -(-18.75 cm)/(12 cm)
m = 1.5625
Therefore, the image is 1.5625 times larger than the object. To find the image height, we multiply the object height by the magnification:
image height = m x object height
image height = 1.5625 x 3.0 cm
image height = 4.6875 cm (rounded to 4.7 cm)
Therefore, the image height is 4.7 cm and it is inverted.
Learn more about height here:-
https://brainly.com/question/10726356
#SPJ11
A flute is played with a first harmonic of 196 Hz (a pitch of G3). The length of the air
column is 89. 2 cm (quite a long flute). Find the speed of the wave resonating in the
flute.
The speed of the wave resonating in the flute is approximately 349.664 m/s. To find the speed of the wave resonating in the flute, we can use the formula:
speed of wave = frequency x wavelength
We know that the frequency of the first harmonic (or fundamental frequency) of the flute is 196 Hz, which corresponds to a pitch of G3.
To find the wavelength, we need to use the formula for the wavelength of a standing wave in an air column that is open at both ends:
wavelength = 2L/n
where L is the length of the air column (in meters) and n is the harmonic number (for the first harmonic, n = 1).
In this case, we're given the length of the air column as 89.2 cm, which is 0.892 meters. So, plugging in the values, we get:
wavelength = 2 x 0.892 / 1
wavelength = 1.784 meters
Now that we have both the frequency and the wavelength, we can calculate the speed of the wave resonating in the flute:
speed of wave = frequency x wavelength
speed of wave = 196 Hz x 1.784 m
speed of wave = 349.664 m/s
So, the speed of the wave resonating in the flute is approximately 349.664 m/s.
Know more about the speed of the wave here:
https://brainly.com/question/10715783
#SPJ11
Why do expanding, aging stars become cooler and more luminous? an overproduction of energy causes the outer layers of gas to expand, whereby the energy is absorbed and the temperature increases. the resulting increase in radiated energy leads to increased luminosity. a decrease in energy causes the outer layers of gas to expand and the temperature to decrease. the resulting increase in radiated energy leads to increased luminosity. a decrease in energy causes the outer layers of gas to expand and the temperature to decrease, and the resulting increase in surface area leads to increased luminosity. an overproduction of energy causes the outer layers of gas to expand. when this happens, the surface area increases rapidly while the temperature decreases rather slowly, and therefore the luminosity increases.
Expanding, aging stars become cooler and more luminous because an overproduction of energy causes the outer layers of gas to expand, whereby the energy is absorbed and the temperature increases. the resulting increase in radiated energy leads to increased luminosity
Define luminosity.
The radiant power that a light-emitting device emits over time is known as luminosity, which is an absolute measure of radiated electromagnetic power. The entire quantity of electromagnetic energy that a star, galaxy, or other celestial object emits over the course of one unit of time is known as luminosity in astronomy.
While the star's core contracts, the outer layers expand, and as the expansion continues, the luminosity rises. The radius and luminosity of a star with the mass of the sun expand 100 times throughout this expansion, which takes place over the course of around a billion years.
To learn more about luminosity use:
https://brainly.com/question/6933301
#SPJ4
Bob has been asked to produce a fuse that has 3. 2 ohms of resistance. He cannot change he thickness of the wire but can change its length. Explain in detail how bob could work out what length of wire to use. You will need to describe the experiment he will need to carry out , any hazards and any variables involved
The wire's resistance at different lengths and analyzing the data, Bob can determine the appropriate length of wire needed to achieve a resistance of 3.2 ohms.
To determine the length of wire Bob needs to achieve a resistance of 3.2 ohms, he can perform an experiment using the wire to measure its resistance at different lengths. Here's a step-by-step explanation of how Bob can carry out the experiment:
1. Gather materials: Bob will need the wire, a power supply (e.g., a battery), an ammeter (to measure current), and a voltmeter (to measure voltage). Ensure all equipment is properly calibrated and suitable for the current and voltage levels.
2. Design a circuit: Bob should set up a simple circuit consisting of the power supply connected in series with the wire, the ammeter to measure the current passing through the wire, and the voltmeter connected across the wire to measure the voltage drop.
3. Safety precautions: It is important for Bob to follow safety protocols while conducting the experiment. He should handle the wire and electrical equipment with care, avoid touching exposed wires, and ensure the circuit is properly insulated. Additionally, he should wear appropriate safety gear such as gloves and goggles.
4. Initial wire length: Bob should start with an initial length of wire and measure its resistance using a multimeter or an ohmmeter. This measurement will serve as the baseline value.
5. Adjusting wire length: Bob can then modify the length of the wire by cutting or extending it. For each length, he needs to ensure the wire is securely connected in the circuit.
6. Recording data: At each wire length, Bob should record the current (I) and voltage (V) values from the ammeter and voltmeter, respectively. These readings will help him calculate the resistance using Ohm's law: R = V/I.
7. Repeat measurements: Bob should repeat the measurements for several different wire lengths to gather enough data points to analyze and determine a trend.
8. Data analysis: Bob can plot a graph of wire length (x-axis) against resistance (y-axis) using the recorded data. By observing the relationship between wire length and resistance, he can identify the length of wire that corresponds to a resistance of 3.2 ohms.
Variables and Hazards:
Independent variable: Wire length. Bob can manipulate this variable by changing the wire's length.
Dependent variable: Resistance. Bob will measure this variable and use it to determine the relationship with the wire length.
Control variables: Bob should keep other factors constant throughout the experiment, such as the thickness of the wire and the material used.
Hazards: The main hazards involved in this experiment are electrical hazards, including electric shock and short circuits. Bob should ensure the circuit is properly insulated, handle the wires and equipment safely, and follow electrical safety guidelines.
To know more about resistance refer here
https://brainly.com/question/30799966#
#SPJ11
Some machines will have a body constructed around a frame for_____
Some machines will have a body constructed around a frame for added structural support and stability.
This design approach ensures that the machine can withstand various forces, stresses, and vibrations that it may encounter during operation. The frame acts as a skeleton, providing a solid foundation for the machine's various components, such as motors, gears, and electronic systems, to be mounted securely.
By constructing the body around the frame, the machine's weight is evenly distributed, helping to prevent any undue strain on individual parts. This structural design can also facilitate easier maintenance, as components can be accessed and replaced more easily.
Additionally, the frame may be designed with specific materials, such as steel or aluminum, to enhance durability and resist corrosion. In summary, constructing a machine's body around a frame provides numerous benefits, including enhanced structural support, improved stability, and easier maintenance.
To know more about machines, refer here:
https://brainly.com/question/2555822#
#SPJ11
Question 6
Two ropes are attached to a tree, and forces of F₁ =2.01 +4.03 N and F₂=3.01+6.01 N
are applied. The forces are coplanar (in the same plane). Find the magnitude of the
net force.
15 N
The net force has a magnitude of C, 5.0 N.
How to determine magnitude?To find the net force, add the two forces vectorially. Break down each force into its x and y components:
F₁ = (2.01 N)î + (4.03 N)ĵ
F₂ = (3.01 N)î + (6.01 N)ĵ
To find the net force, add the components:
F_net = F₁ + F₂ = (2.01 N + 3.01 N)î + (4.03 N + 6.01 N)ĵ
F_net = 5.02î + 10.04ĵ
The magnitude of the net force is given by:
|F_net| = √((5.02 N)² + (10.04 N)²)
|F_net| = √(25.2004 N²)
|F_net| = 5.02 N (rounded to two decimal places)
Therefore, the magnitude of the net force is 5.0 N.
Find out more on coplanar forces here: https://brainly.com/question/28245655
#SPJ1
Two devices of rating 22 W; 220 V and 11 W; 220 V are connected in series. The combination is
connected across a 440 V mains. The fuse of which of the two devices is likely to burn when
switch is on ? Justify your name.
The 11 W device is likely to burn out when the switch is turned on, due to the higher voltage it will be subjected to compared to its rated voltage. It is important to ensure that the devices used in a circuit have the appropriate voltage rating to avoid damage or failure.
When two devices with different power ratings are connected in series, the voltage across each device is divided according to their power ratings. In this case, the two devices are rated 22 W and 11 W, respectively, and are connected in series across 440 V mains. The voltage across each device can be calculated using the formula V = P/I, where V is the voltage, P is the power rating, and I is the current.
For the 22 W device, the voltage across it is V = P/I = 22/0.1 = 220 V. For the 11 W device, the voltage across it is V = P/I = 11/0.1 = 110 V. Therefore, the 22 W device has a voltage rating of 220 V, which is the same as the voltage of the mains, and the 11 W device has a voltage rating of 110 V.
When the switch is turned on, the voltage across the two devices will be the same, which is 220 V. Therefore, the 22 W device will operate normally, but the 11 W device will be subjected to a higher voltage than its rated voltage. As a result, the 11 W device is likely to burn out before the 22 W device.
To learn more about voltage rating
https://brainly.com/question/29734919
#SPJ4
Four forces (1,2,3 and 4) are in the x-y plane and act on an irregularly shaped object
The statement describes an irregularly shaped object experiencing four forces in the x-y plane, and elaborating on its nature, the magnitude and direction of the forces, and their intended outcome provides more context to the scenario.
The given statement describes a scenario in which an object of irregular shape is subjected to four forces acting in the x-y plane. To rephrase this statement, one could start by stating that there is an object, the shape of which is not uniform or regular, and this object is experiencing the influence of four different forces.
These four forces have been designated as 1, 2, 3, and 4, and all of them are acting within the x-y plane. One way to elaborate on this statement is to provide additional context about the nature of the object, the magnitude and direction of the forces, and the intended outcome of this scenario.
For example, the irregularly shaped object could be a vehicle or a piece of machinery, and the four forces could be the result of external factors such as wind, gravity, or applied forces. The magnitude and direction of each force could be significant in determining the overall motion of the object, and the ultimate outcome could be to cause the object to move in a certain direction or to remain stationary despite the presence of the forces.
To learn more about forces
https://brainly.com/question/13191643
#SPJ4
Complete question:
How would you rephrase the statement "Four forces (1,2,3 and 4) are in the x-y plane and act on an irregularly shaped object"?
Would one way more or less on Earth's moon than on the dwarf planet Pluto?Hint: Earth's moon is slightly larger than pluto
Despite the fact that the moon is slightly larger than Pluto, the two bodies are vastly different, and their unique characteristics make them both interesting objects of study for astronomers and space scientists.
Yes, the way things work on Earth's moon would be different from the way they work on Pluto, despite the fact that Earth's moon is slightly larger than Pluto's. This is because the characteristics of a celestial body depend on various factors such as its size, mass, density, and distance from the sun.
One major difference between the two is the gravitational force. The gravitational force on the moon is about one-sixth of that on Earth, while on Pluto, it is about one-fifteenth of that on Earth. This means that objects on the surface of the moon would weigh less than those on Pluto, and they would also fall more slowly.
Another significant difference is the surface conditions. The moon has a relatively smooth surface with little atmosphere and extreme temperature variations, while Pluto has a much more rugged terrain, a thin atmosphere, and a much colder surface with temperatures reaching -240°C.
To learn more about Pluto
https://brainly.com/question/13402868
#SPJ4
a gymnast does cartwheels along the floor and then launches herself into the air and executes several flips in a tuck while she is airborne. if her moment of inertia when executing the cartwheels is and her spin rate is 0.5 rev/s, how many revolutions does she do in the air if her moment of inertia in the tuck is and she has 2.0 s to do the flips in the air?
The gymnast completes 10 revolutions in the air.
The law of conservation of angular momentum states that the total angular momentum of a system remains constant if no external torques act on the system. In this case, the gymnast starts with a certain amount of angular momentum while performing the cartwheels on the ground, and this angular momentum is conserved as she launches herself into the air and performs flips.
Let I1 be the moment of inertia of the gymnast while performing the cartwheels, and omega1 be the spin rate. When she launches into the air, she changes her moment of inertia to I2 and starts rotating at a new spin rate, omega2. According to the law of conservation of angular momentum:
I1 * Ω1 = I2 * Ω2
We can rearrange this equation to solve for omega2:
Ω2 = (I1 * Ω1) / I2
Now, we can use the equation for rotational kinematics:
θ = Ω * t
where theta is the total angle rotated, omega is the spin rate, and t is the time. We can solve for the number of revolutions by converting the angle rotated into revolutions:
revolutions = θ/ (2*pi)
Plugging in the given values, we get:
Ω1 = 0.5 rev/s
I1 = (given)
I2 = (given)
t = 2.0 s
Using the conservation of angular momentum equation, we can solve for omega2:
Ω2 = (I1 * Ω1) / I2
Plugging in the values, we get:
Ω2 = (I1 * 0.5) / I2
Using the equation for rotational kinematics, we can solve for the total angle rotated in radians:
θ = Ω2 * t
Converting this angle to revolutions, we get:
revolutions = θ/ (2*pi)
Plugging in the values, we get:
revolutions = (Ω2 * t) / (2*pi) = 10 revolutions (rounded to the nearest whole number)
To know more about the Inertia, here
https://brainly.com/question/13872538
#SPJ4
