7. Which alarm device does not turn on pressurization fans?
The alarm device that does not turn on pressurization fans is a manual fire alarm pull station.
When activated, it only triggers the fire alarm system and alerts occupants to evacuate the building. It does not control the HVAC (heating, ventilation, and air conditioning) system or turn on pressurization fans.
However, the fire alarm system may be programmed to send a signal to the HVAC system to shut down or change the airflow in response to a fire alarm activation.
Learn more about alarm device, here
https://brainly.com/question/30753003
#SPJ4
If an atmospheric tank is air tested, the pressure should not exceed:
A) 1 inch of water
B) 2 inches of water
C) 2.5 PSIG
D) 14.7 PSIG
Hi! If an atmospheric tank is air tested, the pressure should not exceed:
A) 1 inch of water
Your answer: When air testing an atmospheric tank, the pressure should not exceed 1 inch of water.
Learn more about atmospheric tank: https://brainly.com/question/30649889
#SPJ11
an engineering firm has been contracted for the design ofa parabolic trough solar-thermal power plant. if you were hired as the thermal design engineer, please perform an analysis and find what is the maximum possible working fluid (oil) exit temperature in celsius ? the optimal pipe length is equal to that when the oil exit temperature reaches 95% of the maximum possible temperature in celsius. what is the optimal pipe length ? please explain why the temperature of the oil would not increase after the maximum temperature is reached ?
The steady state is the point where the maximum possible outlet temperature is reached and the temperature remains constant.
Why did temperature remains constant?In order to determine the maximum possible outlet temperature of the working fluid in degrees Celsius, a thermal analysis of the parabolic solar power plant must be carried out. This type of power station uses parabolic mirrors to focus sunlight onto a receiver tube.
The receiver tube is filled with a working fluid that absorbs and heats concentrated sunlight. The heated working fluid then flows through a heat exchanger to produce steam, which drives a turbine to generate electricity.
The maximum possible working fluid exit temperature depends on a number of factors. The optimal pipe length is equal to that when the oil exit temperature reaches 95% of the maximum possible temperature, which is 400°C. The length is based on the thermal analysis of the entire system:
Optimal pipe length = (95/100) * pipe length at maximum temperature
The maximum temperature of the working fluid in the collecting tube does not rise after the maximum temperature has been reached. This is due to the heat transfer processes that take place in the tube.
The steady state is the point where the maximum possible outlet temperature is reached and the temperature remains constant.
learn more about temperature: https://brainly.com/question/25677592
#SPJ1
Which actuator is compatible to press MegaPress rings?
The compatible actuator to press MegaPress rings is the RIDGID RP 340 or similar press tools with the appropriate jaw sets designed for MegaPress fittings. Always ensure to use the correct press tool and jaw set for safe and effective installation.
The actuator that is compatible to press MegaPress rings is the RIDGID RP 340 Press Tool. This tool is designed to work with a variety of pressing systems and is capable of quickly and easily pressing MegaPress rings onto pipes. With its lightweight and ergonomic design, the RIDGID RP 340 makes it easy to handle even the toughest pressing jobs, while its advanced features ensure that every press is precise and consistent. So if you're looking for a reliable and efficient way to press MegaPress rings, the RIDGID RP 340 Press Tool is definitely worth considering.
Know more about compatible actuator here:
https://brainly.com/question/27868153
#SPJ11
In ultrasonic thickness, the higher the temperature of the steel being examined, the:
A) reading cannot be obtained
B) higher the reading
C) lower the reading
D) reading will not be affected
In ultrasonic thickness, the higher the temperature of the steel being examined, the: higher the reading.
In ultrasonic thickness testing, the sound waves are sent through the material being examined, and the time it takes for the waves to bounce back is used to calculate the thickness. However, the speed of sound waves in a material is affected by temperature. In general, as the temperature of steel increases, the speed of sound waves through it also increases. This means that the ultrasonic waves will travel through the steel faster, and the measurement of thickness will be slightly higher than it would be at a lower temperature. Therefore, the higher the temperature of the steel being examined, the higher the reading in ultrasonic thickness testing.
To know more about ultrasonic thickness
https://brainly.com/question/21336084?
#SPJ11
Briefly describe the behavior of the Lisp/Scheme read-eval-print loop.
The Lisp/Scheme read-eval-print loop follows a simple pattern of reading an expression from the input, evaluating it, and then printing the result.
This process continues until the user decides to exit the loop. The read function reads the input as an S-expression and converts it into a Lisp/Scheme data structure. The eval function then takes this data structure and evaluates it, returning the result of the expression. Finally, the print function takes the result and displays it to the user. The read-eval-print loop is the heart of the Lisp/Scheme interpreter and allows users to interactively explore and experiment with the language.
Learn more about Lisp/Scheme: https://brainly.com/question/17466042
#SPJ11
During a tank repair, if API 653 conflicts with the design standard, which standard governs?
A) Most stringent standard
B) Design Standard
C) API 653
D) Either standard based on the inspector's judgment
Hi!
Question: "During a tank repair, if API 653 conflicts with the design standard, which standard governs?"
In the case where API 653 conflicts with the design standard during a tank repair, the governing standard is:
C) API 653
Learn more about design standard: https://brainly.com/question/24298037
#SPJ11
05-004 - Definition of data analysis fairness
05-004 refers to a specific code or reference number that may be related to a particular topic or document. In terms of the definition of data analysis fairness, it refers to the practice of ensuring that the analysis of data is conducted in a manner that is unbiased and objective. This means that data is collected and analyzed in a way that is free from any personal or institutional biases, and that the findings are presented in a transparent and objective manner. Fairness in data analysis is essential for ensuring that decisions based on data are accurate, reliable, and equitable. It is also important for maintaining trust and confidence in the data and the individuals or organizations responsible for collecting and analyzing it.
To know more about data analysis fairness
https://brainly.com/question/31594489?
#SPJ11
At what max press does the hydraulic system operate
The maximum pressure at which a hydraulic system operates will depend on the specific design and application of the hydraulic system.
We have,
Hydraulic systems are widely used in many different types of machinery and equipment, such as aircraft, industrial machinery, and automotive systems, and each system may have its own maximum operating pressure.
For example, in aircraft hydraulic systems, the maximum operating pressure can vary depending on the aircraft type and the specific hydraulic system design.
The maximum pressure may be specified in the aircraft's operating manual or maintenance documentation, and it's critical to operate the hydraulic system within these limits to ensure safe and reliable operation.
Thus,
The maximum pressure at which a hydraulic system operates will depend on the specific design and application of the hydraulic system.
Learn more about hydraulic systems here:
https://brainly.com/question/30615986
#SPJ4
___________________is an application programming interface (API) that was developed in the early 1980s to allow computer-to-computer communication on a small LAN (specifically, PC-Network, which was IBM's LAN technology at the time).
NetBIOS (Network Basic Input/Output System) is an application programming interface (API) that was developed in the early 1980s to allow computer-to-computer communication on a small LAN using IBM's PC-Network technology. NetBIOS was initially used in IBM's LAN Manager product and later became a standard protocol for LAN communication on Microsoft Windows-based systems.
NetBIOS provides a set of programming interfaces for applications to perform basic network operations such as naming, session establishment, and message transfer. It is primarily used for peer-to-peer communication between computers on a LAN and is often used by file and printer sharing services.
NetBIOS can operate over several transport protocols, including TCP/IP, IPX/SPX, and NetBEUI. However, NetBEUI is a proprietary protocol developed by Microsoft, and its use has been largely phased out in favor of TCP/IP.
Overall, NetBIOS played an important role in the early development of LAN communication and continues to be used in some legacy systems today.
learn more about NetBIOS Here:
https://brainly.com/question/15085605
#SPJ11
Why must gens be off for GPU start
Gens or generators are typically used as a backup power source for buildings or facilities in case of a power outage. When it comes to starting a GPU (graphics processing unit) or a computer's graphics card, it is important to turn off the gens to ensure that the power being supplied to the GPU is consistent and stable.
For such more question on inconsistent
https://brainly.com/question/15654281
#SPJ11
Replacement and new penetrations, in reconstructed tanks, shall be designated, detailed, welded, and examined to meet what requirements?
A) The current applicable standard
B) The original standard construction
C) The requirements of the Authorized Inspector
D) The requirements of the owner/operator
Hi! Question is: "Replacement and new penetrations, in reconstructed tanks, shall be designated, detailed, welded, and examined to meet what requirements?"
Replacement and new penetrations, in reconstructed tanks, shall be designated, detailed, welded, and examined to meet the requirements of A) The current applicable standard.
Learn more about reconstructed tanks: https://brainly.com/question/30238671
#SPJ11
which of the following statements is false for discontinuous chips? group of answer choices they are generated using cutting tools with small rake angles. they will produce a poorer surface finish on the part. they are formed when machining at high cutting speeds and fine feed rates. they are formed when brittle materials are machined.
The statement that is false with regard to discontinuous chips is given as: "they are formed when machining at high cutting speeds and fine feed rates.
What is the explanation for the above response?Note that chips that are discontinuous are usually formed when brittle material are machined or when tools are being cut with small rake angles.
Machining at high cutting speeds in addition to fine feed rates will always translate to the creation of continuous chips. Hence the statement is false.
Learn more about machine at:
https://brainly.com/question/30492354
#SPJ4
The structure and corresponding properties of a material are influenced by how it is processed. True or false?
True. The processing methods used to manufacture or synthesize a material can have a significant influence on its structure and corresponding properties. Processing can affect the arrangement of atoms,
molecules, or particles within a material, leading to changes in its physical, chemical, mechanical, electrical, and other properties. For example, in metals, the processing method can affect the grain size, crystal orientation, and defect density, which can in turn impact properties such as strength, ductility, and electrical conductivity. In polymers, the processing conditions, such as temperature, pressure, and cooling rate, can influence the polymer chain arrangement, molecular weight, and crystallinity, which can affect properties such as tensile strength, thermal stability, and transparency. In ceramics, the processing technique can affect the porosity, grain size, and phase composition, which can impact properties such as hardness, fracture toughness, and thermal conductivity.
learn more about material here:
https://brainly.com/question/30503992
#SPJ11
what storyboarding technique uses a combination of two techniques, and which techniques does it combine?
The storyboarding technique uses a combination of two techniques, and which techniques does it combine is option C: webbed; linear and hierarchical
What is the storyboarding technique?In the movie business, storyboards are used to meticulously plot out an entire movie before it is filmed. The initial shot, or camera angle, is depicted in the opening of the storyboard for the first scene. The following illustration on the story board depicts the following shot from a different perspective.
Therefore, Thumbnail Storyboarding is the name of the storyboarding method that combines linear storyboarding and thumbnail drawing. This method entails making a series of quick sketches that reflect the shots in the order they will be seen in the movie.
Learn more about storyboarding technique from
https://brainly.com/question/26102459
#SPJ4
What storyboarding technique uses a combination of two techniques, and which techniques does it combine?
A.
hierarchical; wheel and linear
B. linear, webbed and hierarchical
C. webbed; linear and hierarchical
D. wheel: webbed and linear
Reset
Next
Nanomaterials are classified not by their chemistry but by their length scale (ie., size). True or false?
True. Nanomaterials are classified based on their size or length scale, typically in the nanometer range (1-100 nanometers), rather than their chemistry. The term "nano" refers to the nanometer scale,
which is a unit of measurement equivalent to one billionth of a meter. Nanomaterials exhibit unique properties and behaviors at the nanoscale, which can differ from their bulk counterparts. These unique properties make nanomaterials suitable for various applications in fields such as electronics, medicine, energy, and materials science. The classification of nanomaterials based on size or length scale rather than chemistry reflects the importance of the nanoscale dimension in determining their properties and behavior.
learn more about Nanomaterials here:
https://brainly.com/question/14910031
#SPJ11
A 30,000 sq/ft office floor would require how many deputy floor wardens?
A. one
B. two
C. three
D. four
A 30,000 sq/ft office floor would require D. four deputy floor wardens.
Why would A 30,000 sq/ft office floor would require D. four deputy floor wardens?In some organizations, there is general rule that is to have one deputy floor warden for every 7,500 sq/ft of office space. Looking at this type of guideline, a 30,000 sq/ft office floor would indeed require four deputy floor wardens:
30,000 sq/ft / 7,500 sq/ft per deputy floor warden = 4 deputy floor wardens.
Depending on the organization's safety procedures, regional laws, and the building's design, the number of deputy floor wardens needed for a particular office level can change.
Find more exercises on warden;
https://brainly.com/question/12071861
#SPJ1
Strain hardening is a phenomenon whereby a metal becomes ___________ as it is plastically deformed due to an increase in dislocation density within the material.
Strain hardening is a phenomenon whereby a metal becomes stronger as it is plastically deformed due to an increase in dislocation density within the material.
When a metal is plastically deformed, dislocations, which are defects in the crystal structure of the material, move and multiply within the metal. As the dislocation density increases, the movement of dislocations becomes more difficult, which makes it harder for the material to deform further.
This increase in dislocation density leads to an increase in the strength and hardness of the material, as the dislocations act as barriers to the movement of other dislocations and to the motion of defects such as voids or cracks. This is why metals that have undergone significant plastic deformation, such as cold working or rolling, are typically stronger and harder than the same material in an annealed or unworked state.
learn more about plastically deformed Here :
https://brainly.com/question/12975550
#SPJ11
19. Higher temperature sprinkler heads used in ordinary rooms will have what effect?
Higher temperature sprinkler heads used in ordinary rooms will activate at higher temperatures, which may result in a longer delay in the activation of the sprinkler system in the event of a fire.
What is a Higher temperature sprinkler?Higher temperature sprinkler heads are a type of automatic fire sprinkler system that are designed to activate at higher temperatures than standard sprinkler heads. These sprinkler heads are typically used in areas where higher temperatures are present or in rooms with higher ceilings.
Higher temperature sprinkler heads are designed to activate at temperatures ranging from 175 to 300 degrees Fahrenheit, compared to the 135 to 170 degrees Fahrenheit range for standard sprinkler heads. This allows for a longer delay in the activation of the sprinkler system in the event of a fire, which can be beneficial in situations where false activations could cause significant damage or disruption.
Learn more about Higher temperature sprinkler, here:
https://brainly.com/question/28224439
#SPJ4
Ultimate responsibility for compliance with API Standard 653 rest with _____?
A) The owner/operator
B) the owner/operators' inspector
C) The repair organization of the Owner/operator
D) the manufacturing of the AST
Answer:
D!
Explanation:
Have a good day!
<3
Purpose of status meetings:Exchange info on projectHave team members report what they are doingIssue work authorizationsConfirm accuracy of costs submitted
The purpose of status meetings is to exchange information on the project and have team members report on what they are doing. Additionally, status meetings are used to issue work authorizations and confirm the accuracy of costs submitted.
By discussing progress and any issues or challenges, status meetings can help keep the project on track and ensure that all team members are aligned towards the common goal. Overall, status meetings are an important tool for project management and can help ensure successful project outcomes.Exchange information on the project: Status meetings provide an opportunity for team members to share updates, progress, and any issues or concerns related to the project. This helps ensure everyone is on the same page and has a clear understanding of the project status.Have team members report what they are doing: Status meetings allow team members to report on their individual tasks and responsibilities, which helps the PM to assess members , identify any issues, and make necessary adjustments.Issue work authorizations: If new tasks or responsibilities need to be assigned, status meetings can be used to issue work authorizations and delegate tasks to specific team members.
To learn more about members click the link below:
brainly.com/question/30461727
#SPJ11
What type of forensic data is recovered using a carving tool?
A carving tool is often used in digital forensics to recover deleted or hidden data from electronic devices such as computers, smartphones, and cameras. This type of data recovery is known as "carving" and it involves using software tools and techniques to reconstruct fragmented data that has been deleted or otherwise lost. The type of forensic data that can be recovered using a carving tool includes images, videos, documents, emails, and other types of digital files that may have been intentionally or unintentionally deleted or obscured. The data recovered through carving can be crucial in investigations and legal proceedings, as it can provide valuable evidence and insights into criminal activities or other forms of wrongdoing.
To know more about forensics
https://brainly.com/question/14403044?
#SPJ11
Which feature enables a single-core CPU to function like two CPUs?
The feature that enables a single-core CPU to function like two CPUs is called hyper-threading. It allows a single CPU to perform multiple tasks simultaneously, as if it were two separate CPUs.
Hyper-threading is achieved by duplicating certain components of the CPU that are used less frequently, such as the program counter and registers, which enables the CPU to more efficiently use its resources and increase its processing power.
The feature that enables a single-core CPU to function like two CPUs is called "hyper-threading." Hyper-threading is a technology developed by Intel that allows a single-core processor to execute multiple threads simultaneously. It does this by creating virtual cores, or "logical processors," which the operating system sees as additional CPU cores.
With hyper-threading, the CPU can work on two threads at the same time, switching between them quickly and efficiently. This can help improve performance in certain applications, particularly those that can take advantage of multiple threads.
It's important to note that hyper-threading does not actually double the physical number of cores in the CPU. Rather, it allows a single physical core to function as if it were two logical cores. As such, the performance gains from hyper-threading are not as significant as those from having a true multi-core processor.
to know more about CPU:
https://brainly.com/question/30751834
#SPJ11
___________________ , a data stream is divided into messages. Each message is tagged with a destination address, and the messages travel from one network device to another network device on the way to their destination.
In packet-based communication networks, a data stream is divided into packets. Each packet is tagged with a destination address, and the packets travel from one network device to another network device.
In packet-based communication, data is broken down into smaller packets, each containing a portion of the original data along with additional header information that includes the source and destination addresses. These packets are then independently routed across the network, often through multiple intermediate network devices such as routers, switches, and bridges, based on the destination address in their headers. The network devices use routing protocols and tables to determine the most appropriate path for the packets to reach their destination based on factors such as network topology, congestion, and quality of service (QoS) requirements.
As the packets traverse the network, they may be processed, forwarded, and reassembled at their destination to reconstruct the original data stream. This process allows for efficient and flexible communication across complex networks, as packets can take different paths and be processed independently, allowing for efficient utilization of network resources and fault tolerance.
learn more about network here:
https://brainly.com/question/15088389
#SPJ11
when did construction on the bell bomber plant start?
Construction on the Bell Bomber Plant, also known as the Marietta B-29 Plant, started in late 1942, during World War II, as the Bell Bomber Plant was built by the US government to produce B-29 Superfortress bombers.
The construction of the Bell Bomber Plant was completed in record time, and the first B-29 bomber rolled off the assembly line in September 1944. The plant produced a total of 668 B-29 bombers during its operation, making a significant contribution to the US war effort. After the end of World War II, the plant was used for various purposes, including the production of commercial aircraft and military helicopters. The plant was eventually sold to Lockheed Martin Corporation and continues to operate as a major aerospace manufacturing facility.
Learn more about the Bell Bomber Plant here.
https://brainly.com/question/12085083
#SPJ4
At the atomic scale, elastic deformation corresponds to breaking of interatomic bonds whereas plastic deformation corresponds to stretching of interatomic bonds. True or false?
Elastic deformation corresponds to the stretching of interatomic bonds while plastic deformation corresponds to the breaking and rearrangement of interatomic bonds.
Elastic deformation occurs when a material is subjected to stress, but it can return to its original shape when the stress is removed. This is because the interatomic bonds between atoms are stretched, but not broken. On the other hand, plastic deformation occurs when a material is subjected to stress beyond its elastic limit, causing permanent deformation. This is because the interatomic bonds are stretched to the point where they break and rearrange themselves. Therefore, elastic deformation corresponds to the stretching of interatomic bonds, while plastic deformation corresponds to the breaking and rearrangement of interatomic bonds.
Learn more about Elastic deformation here:
https://brainly.com/question/29996154
#SPJ11
04-010 - SQL. What are two ways to insert a comment in a SQL statement?
The two ways to insert a comment in a SQL statement are:
1. Using double hyphens (--) for single-line comments: Place the double hyphens before the comment text, and everything on the same line after them will be treated as a comment.
Example:
```sql
-- This is a single-line comment
SELECT * FROM tableName;
```
2. Using /* and */ for multi-line comments: Enclose the comment text between /* and */ symbols. This allows comments to span multiple lines.
Example:
```sql
/*
This is a multi-line comment
It can span multiple lines
*/
SELECT * FROM tableName;
```
These methods allow you to insert comments in your SQL statements for better code readability and documentation.
TOo know more about SQL statement
https://brainly.com/question/30364070?
#SPJ11
to keep up with faster processors, motherboard makers began to double and quandruple throughout the frontside bus. This is called by techs double-pumped and quad-pumped frontside buses
In order to keep up with the demands of faster processors, motherboard makers have implemented various improvements over the years. One such improvement has been to double or quadruple the speed of the frontside bus, which is responsible for carrying data between the processor and the motherboard. This technique is known as "double-pumping" or "quad-pumping" the frontside bus, and it allows for faster and more efficient communication between the processor and other components on the motherboard.
By doubling or quadrupling the frontside bus, motherboard makers are able to provide a faster pathway for data to travel between the processor and other components such as RAM, graphics cards, and storage devices. This can result in significant performance improvements for tasks that require a lot of data processing, such as gaming, video editing, and other intensive applications.
Overall, the trend towards double and quad-pumped frontside buses is just one example of how motherboard makers are constantly working to improve performance and keep up with the demands of faster processors and other advanced technologies.
to know more about processor:
https://brainly.com/question/28902482
#SPJ11
What function does the external data bus have in the PC?
The external data bus serves as the communication pathway between the computer's CPU and external devices, such as RAM, hard drives, and input/output devices. Its main function is to transfer data between these external devices and the computer's internal components, allowing for the efficient and accurate operation of the PC. Without the external data bus, the computer would not be able to properly interact with its external environment, leading to a breakdown in functionality.
What function does the external data bus have in the PC?
The external data bus in a PC is responsible for facilitating communication between the CPU (central processing unit) and other devices in the computer, such as memory, input/output (I/O) devices, and expansion cards. The external data bus is a set of parallel electrical lines that allow data to be transferred between the CPU and other devices.
The external data bus is often referred to as the system bus, and it consists of three types of signals: address signals, data signals, and control signals. Address signals are used to specify the memory or I/O location that the CPU wants to access. Data signals carry the actual data being transferred between the CPU and the device. Control signals are used to manage the timing and sequencing of data transfers.
The width of the external data bus determines the amount of data that can be transferred between the CPU and other devices at any given time. Older PCs typically had data buses that were 8 bits wide, while modern PCs have data buses that are 64 bits wide or even wider. A wider data bus allows for faster data transfer rates and better overall system performance.
In summary, the external data bus is a critical component in a PC that allows the CPU to communicate with other devices in the system, facilitating data transfer and overall system performance.
to know more about communication:
https://brainly.com/question/22558440
#SPJ11
True or false? SOAR is intended to provide wholly automated incident response solutions.
True
SOAR, which stands for Security Orchestration, Automation, and Response, is designed to provide wholly automated incident response solutions. It streamlines security operations by automating tasks, orchestrating workflows, and enabling rapid response to security incidents.
The final battle of the epic poem "Odyssey" by Homer is foreshadowed by using the symbol of two eagles that were send by Zeus. These two eagles were omens of death, which flew down from the mountains tearing each other apart into pieces as they flew over the crowd. The prophet Halitherses interpreted this event as an omen of death send by Zeus.
To know more abour SOAR
https://brainly.com/question/11596539?
#SPJ11
