Please hurry, being timed. And no links !!!


A ball weighing 10 kg rolls down a frictionless incline with a 50 degree angle to the horizontal. If the balls initial velocity was 0 m/s, how much does the mechanical energy of the system change by the time the ball reaches its destination.


A. Increases by 12%


B. Increases by 58%


C. Decreases by 12%


D. Does not change

Answers

Answer 1

The mechanical energy of the system decreases by 12% (152.70 J/751.98 J x 100%) when the ball reaches its destination. Therefore, the correct answer is C. Decreases by 12%.

What is Energy?

Energy is a fundamental physical quantity that describes the ability of a system to do work. In other words, energy is the capacity of a system to produce changes in itself or in its environment. It is a scalar quantity, which means that it is characterized only by its magnitude and not by its direction.

When the ball reaches the bottom of the incline, it will have a velocity v given by v = [tex]\sqrt{2gh}[/tex], where h is the height of the incline. Substituting the values, we get v = [tex]\sqrt{29.817.66}[/tex] = 10.99 m/s.

The final kinetic energy of the ball is given by (1/2)m[tex]v^{2}[/tex] = (1/2)[tex]1010.99^{2}[/tex] = 599.28 J.

The final potential energy of the ball is 0, since it is at ground level. Therefore, the total mechanical energy of the system at the bottom of the incline is the sum of the final kinetic and potential energies, which is 599.28 J.

The initial mechanical energy of the system is the potential energy of the ball at the top of the incline, which is 751.98 J.

Therefore, the change in mechanical energy is:

Delta E = 599.28 - 751.98 = -152.70 J

To know more about Energy visit;

https://brainly.com/question/8101588

#SPJ4


Related Questions

In a recent movie, a car and a truck had a head on collision. The car was moving to the right with a constant speed of 21 m/s. A parked truck that was 310 m in front of the car began moving to the left and speeding up at a rate of 1.2 m/s/s. Position 0 m is the car's initial position.

What is the position of the car after 4 seconds?
What is the position of the truck after 4 seconds?
What is the velocity of the truck upon impact with the car?
How much time passes before the collision happens?
Where do the car and truck collide?

Answers

Answer:To solve this problem, we need to use the equations of motion and kinematics.

1. What is the position of the car after 4 seconds?

The position of the car after 4 seconds can be found using the equation:

position = initial position + (initial velocity x time) + (1/2 x acceleration x time^2)

Plugging in the values, we get:

position = 0 + (21 x 4) + (1/2 x 0 x 4^2) = 84 meters

Therefore, the position of the car after 4 seconds is 84 meters.

2. What is the position of the truck after 4 seconds?

The position of the truck after 4 seconds can be found using the equation of motion for uniform acceleration:

position = initial position + (initial velocity x time) + (1/2 x acceleration x time^2)

Initial velocity of the truck is zero, and the acceleration is 1.2 m/s^2. The initial position of the truck is 310 meters ahead of the car.

Plugging in the values, we get:

position = 310 + (0 x 4) + (1/2 x 1.2 x 4^2) = 326.4 meters

Therefore, the position of the truck after 4 seconds is 326.4 meters.

3. What is the velocity of the truck upon impact with the car?

To find the velocity of the truck upon impact with the car, we need to use the equation:

final velocity = initial velocity + acceleration x time

The initial velocity of the truck is zero, the acceleration is 1.2 m/s^2, and the time is the time it takes for the collision to happen.

4. How much time passes before the collision happens?

To find the time it takes for the collision to happen, we need to use the equations of motion and kinematics.

The position of the car at the time of the collision is the same as the position of the truck at the time of the collision. Let's call this position "x".

Using the equation of motion for the car, we have:

x = 0 + (21 x t) + (1/2 x 0 x t^2) = 21t

Using the equation of motion for the truck, we have:

x = 310 + (0 x t) + (1/2 x 1.2 x t^2) = 0.6t^2 + 310

Setting these two equations equal to each other, we get:

21t = 0.6t^2 + 310

Simplifying and solving for t, we get:

t = 23.98 seconds

Therefore, the time it takes for the collision to happen is approximately 24 seconds.

5. Where do the car and truck collide?

The position of the collision can be found by plugging the time into either the equation of motion for the car or the equation of motion for the truck.

Using the equation of motion for the car:

position = 21 x 23.98 = 503.58 meters

Using the equation of motion for the truck:

position = 0.6 x (23.98)^2 + 310 = 503.58 meters

Therefore, the car and truck collide at a position of 503.58 meters.

Explanation:

If a 325 W heater has a current of 6.0 A, what is the resistance of the heating element?
O 10 Ohms
O 50 Ohms
88 Ohms
9 Ohms

Answers

The resistance of the heating element is 9 Ohms

What is Ohm's law?

Ohm's law states that the current (I) flowing through a conductor between two points is directly proportional to the voltage (V) across the two points and inversely proportional to the resistance (R) between them. Mathematically, this can be expressed as:

V = IR

Equation:

In this scenario, we are given the power (P) and current (I) of a heater, and we are asked to find its resistance (R). Power can be calculated using:

P = IV

where V is the voltage across the heater. Since we are not given the voltage, we can rearrange Ohm's law to solve for the resistance:

R = V/I

Substituting the formula for power into this equation, we get:

R = (V/I) = (P/I²)

Substituting the given values of power and current, we get:

R = (325 W) / (6.0 A)² = 9.0 Ohms

The correct answer is (D).

To know more about Ohm's law, click here

https://brainly.com/question/1247379

#SPJ1

A toaster is listed as 1560 w. when it is plugged into a 120 v circuit and starts to make toast, how many amperes will it draw

Answers

The toaster will draw 13.0 amperes when plugged into a 120-volt circuit.

To calculate the amperage that the toaster will draw, we can use Ohm's Law which states that the current flowing through a circuit is equal to the voltage divided by the resistance.

However, we need to first determine the resistance of the toaster.

From the given information, we know that the toaster is rated at 1560 watts and is operating at 120 volts.

Therefore, we can calculate the resistance using the formula R = [tex]V^{2}[/tex] / P, where V is the voltage and P is the power.

R = [tex](120)^{2}[/tex] / 1560 = 9.23 ohms

Now that we know the resistance, we can use Ohm's Law to calculate the current drawn by the toaster:

I = V / R = 120 / 9.23 = 13.0 A

Therefore, the toaster will draw 13.0 amperes when plugged into a 120-volt circuit.

To know more about Ohm's Law, refer here:

https://brainly.com/question/1247379#

#SPJ11

A vessel is filled with a gas at a temperature 30c and a pressure of 760mmhg calculate the final pressure if the volume of the gas is double while it's heated at 80c

Answers

To solve this problem, we can use the combined gas law, which relates the pressure, volume, and temperature of a gas:

(P1 x V1) / T1 = (P2 x V2) / T2

where P1, V1, and T1 are the initial pressure, volume, and temperature, and P2, V2, and T2 are the final pressure, volume, and temperature, respectively.

First, let's convert the initial temperature of 30°C to Kelvin:

T1 = 30°C + 273.15 = 303.15 K

We can now set up the equation with the initial conditions:

(760 mmHg x V1) / 303.15 K = (P2 x 2V1) / 353.15 K

where V1 is the initial volume of the gas.

Simplifying this equation by multiplying both sides by 303.15 K and dividing by 2V1, we get:

P2 = (760 mmHg x 303.15 K) / (353.15 K) = 653.75 mmHg

Therefore, the final pressure of the gas is 653.75 mmHg when the volume is doubled and the temperature is increased to 80°C.

Because the human body is a holistic organism, this means that



A. Each person reacts to stress the same way



B. Physical injuries do not affect mental processes



C. Religion plays a key role in how people react to stress



D. A negative effect in one area can affect others areas

Answers

Because the human body is a holistic organism, this means that D. A negative effect in one area can affect others areas.

This is because all the components of the human body are interconnected, and any disturbance in one part may have repercussions on other parts as well.

When there is a negative effect or disturbance in one area of the body, it can indeed have repercussions on other areas. Here are a few reasons why this occurs:

Physiological Systems: The human body is composed of several physiological systems, such as the cardiovascular system, respiratory system, digestive system, and nervous system, among others.

These systems work in harmony to maintain homeostasis and support each other's functions. Disruption or dysfunction in one system can affect the functioning of other systems, as they are interdependent.

Communication Pathways: The body relies on complex communication pathways to transmit signals and information between different organs and tissues. Hormones, neurotransmitters, and electrical impulses are examples of the communication mechanisms involved.

When there is an issue in one area, it can interfere with the signaling pathways and disrupt the communication network, potentially impacting other areas that rely on these signals.

Compensation Mechanisms: The body often has built-in compensation mechanisms to adapt and maintain balance when faced with challenges or disturbances.

However, if a negative effect persists or overwhelms the compensatory abilities, it can lead to imbalances or compromises in other areas that are trying to compensate. This can manifest as symptoms or further complications.

Blood Circulation: Blood circulation plays a vital role in distributing oxygen, nutrients, and various substances throughout the body.

Any disruption in blood flow, such as blockages or decreased perfusion, can affect multiple organs and tissues, as they rely on a steady supply of oxygen and nutrients for proper functioning.

To learn more about circulation, refer below:

https://brainly.com/question/16144348

#SPJ11

Two uniform solid spheres have the same mass, 1.75 kg, but one has a radius of 0.206 m while the other has a radius of 0.834 m. for each of the spheres, find the torque required to bring the sphere from rest to an angular velocity of 327 rad/s in 15.5 s. each sphere rotates about an axis through its center. torque on sphere with the smaller radius.

Answers

The torque required for the sphere with the smaller radius is approximately 0.622 N*m.

To find the torque required for each sphere, we need to first calculate the moment of inertia (I) for each sphere, and then use the formula for torque (τ) which is τ = I * α, where α is the angular acceleration.

The moment of inertia for a solid sphere is given by I = (2/5) * M * R^2, where M is the mass and R is the radius.

For the smaller sphere (radius = 0.206 m):
I₁ = (2/5) * 1.75 kg * (0.206 m)^2 ≈ 0.0295 kg*m^2

For the larger sphere (radius = 0.834 m):
I₂ = (2/5) * 1.75 kg * (0.834 m)^2 ≈ 0.5093 kg*m^2

Next, we need to find the angular acceleration (α) using the formula α = Δω/Δt, where Δω is the change in angular velocity and Δt is the time interval.

Δω = 327 rad/s (final angular velocity) - 0 rad/s (initial angular velocity) = 327 rad/s
Δt = 15.5 s

α = 327 rad/s / 15.5 s ≈ 21.1 rad/s^2

Now, we can find the torque (τ) for each sphere using τ = I * α.

Torque for smaller sphere:
τ₁ = 0.0295 kg*m^2 * 21.1 rad/s^2 ≈ 0.622 N*m

Torque for larger sphere:
τ₂ = 0.5093 kg*m^2 * 21.1 rad/s^2 ≈ 10.76 N*m

So, the torque required for the sphere with the smaller radius is approximately 0.622 N*m.

To learn more about acceleration, refer below:

https://brainly.com/question/12550364

#SPJ11

A spaceship has four thrusters for movement. Each thruster can fire exhaust gases away from the ship, causing it to move. Firing which pairs of thrusters together would cause the ship to remain stationary?

Thrusters 1 and 2

, Thrusters 1 and 2 , ,

Thrusters 1 and 3

, Thrusters 1 and 3 , ,

Thrusters 3 and 4

, Thrusters 3 and 4 , ,

Thrusters 2 and 3

, Thrusters 2 and 3 , ,

Thrusters 1 and 4

, Thrusters 1 and 4 , ,

Thrusters 2 and 4

Answers

The two pairs of thrusters that would cause the spaceship to remain stationary when fired together are: Thrusters 1 and 2, and Thrusters 3 and 4.

Thrust is the force that propels an object forward, and it is created by the expulsion of gas or liquid out of a nozzle. In the case of a spaceship, the thrusters create thrust by expelling exhaust gases away from the ship, which propels it forward.

Now, let's consider the thrusters on this spaceship. There are four thrusters available for movement, which means that there are six possible pairs of thrusters that can be fired together. However, not all of these pairs will result in the ship remaining stationary.

To keep the spaceship stationary, the thrusters need to create an equal and opposite force to cancel out the movement created by the other thrusters. This means that the pairs of thrusters that need to be fired together are those that are opposite each other.

we need to consider the opposite forces acting on the ship. If two thrusters generate equal and opposite forces, the net force will be zero, and the spaceship will remain stationary.

Assuming the thrusters are arranged symmetrically around the spaceship, firing Thrusters 1 and 2 together or Thrusters 3 and 4 together would likely create equal and opposite forces. This is because the forces generated by these pairs would cancel each other out, keeping the ship stationary.

Therefore, the two pairs of thrusters that would cause the spaceship to remain stationary when fired together are Thrusters 1 and 2, and Thrusters 3 and 4.

To know more about thrusters, refer here:

https://brainly.com/question/30154005#

#SPJ11

Complete question:

A spaceship has four thrusters for movement. Each thruster can fire exhaust gases away from the ship, causing it to move. Firing which pairs of thrusters together would cause the ship to remain stationary?

Select two that apply

Thrusters 3 and 4

Thrusters 1 and 2

Thrusters 1 and 3

Thrusters 2 and 4

Thrusters 2 and 3

Thrusters 1 and 4

whats the sum of (8+3m)+(-2+4x)+(9+8d)

Answers

Answer:

15 + 3m + 4x + 8d

Explanation:

in an rlc series circuit as shown, there is a phase angle between the instantaneous current through the circuit and the instantaneous voltage vad across the entire circuit. for what value of the phase angle is the greatest power delivered to the resistor? group of answer choices 900 2700 zero 1800

Answers

The phase angle that maximizes the power delivered to the resistor is zero degrees. So, correct option is C.

In an RLC series circuit, the impedance Z is given by the equation Z = R + j(XL - XC), where R is the resistance, XL is the inductive reactance, and XC is the capacitive reactance. The current in the circuit is given by the equation I = V/Z, where V is the voltage across the circuit.

The power delivered to the resistor in the circuit is given by the equation P = I^2R. To maximize this power, we need to maximize the current I in the circuit.

The phase angle between the current and voltage is given by the equation tan(phi) = (XL - XC)/R, where phi is the phase angle. This means that the phase angle is zero when XL = XC, or when the reactances cancel out.

At this point, the impedance of the circuit is purely resistive and is equal to R. This means that the current is at its maximum value, which maximizes the power delivered to the resistor.

Therefore, correct option is C.

To learn more about phase angle click on,

https://brainly.com/question/29331145

#SPJ4

Complete question is:

in an rlc series circuit , there is a phase angle between the instantaneous current through the circuit and the instantaneous voltage vad across the entire circuit. for what value of the phase angle is the greatest power delivered to the resistor? group of answer choices

A)90

B)270

C) zero

D) 180

A certain one-dimensional conservative force is given as a function of x by the expression F =-kx^3, where F is in newtons and x is in meters. A possible potential energy function U for this force is

Answers

Option (D) is correct.

The relation between potential energy(U(x)) and the associated force(F(x)) can be given as,

F(x) = (-)(dU/dx)

Therefore,

[tex]dU = (-) \int\limits^x_0{F(x)} .\, dx[/tex]

On putting, F(x) = (-)kx^3, and integrating, we have

[tex]U = \frac{1}{4}.k.x^{4}[/tex]

So, a possible energy function U for this force is, U = ((k.x^4)/4).

Thus, option (D) is correct.

Read more about force and potential energy at:
https://brainly.com/question/29998972

Titan Tommy and the Test Tubes at a night club this weekend. The lead


instrumentalist uses a test tube (closed-end air column) with a 17. 2 cm air column. The


speed of sound in the test tube is 340 m/sec. Find the frequency of the first harmonic


played by this instrument.

Answers

The frequency of the first harmonic played by the instrument is approximately 990.7 Hz.

The frequency of the first harmonic played by the instrument can be calculated using the formula:

f = v / (2L)

where f is the frequency, v is the speed of sound in the test tube, and L is the length of the air column in the test tube.

The speed of sound in test tube is, 340 m/s.

In this case, L = 17.2 cm = 0.172 m. Substituting the given values into the formula, we get:

f = 340 m/s / (2 * 0.172 m)

f = 990.7 Hz

To know more about frequency, here

brainly.com/question/5102661

#SPJ4


Please it due today need help!!!



Gender shifts are actually a common phenomenon in public roles (employment,
entertainment, or otherwise). Identify a role and explain if there is a status change
in the role - as in how these women or non binary folks are treated by the others
in the situation (still treated as women/non-binary or as if they are men-explain).

Answers

One example of a role where gender shifts occur is politics. Women and non-binary individuals who enter the political sphere often experience a shift in their status and how they are treated by others. They may be viewed as less competent or capable than their male counterparts, or face discrimination and bias based on their gender identity. However, as more women and non-binary individuals are elected to political positions, there is a growing recognition of their abilities and contributions, and a shift towards greater gender equality in the political realm. Despite this progress, there is still much work to be done to address the systemic barriers that prevent women and non-binary individuals from fully participating in politics and achieving equal status and treatment.

One example of a role where gender shifts have occurred is in the field of politics, particularly in positions of political leadership. In many countries around the world, women are increasingly being elected to high-level political positions traditionally held by men, such as heads of state, prime ministers, and cabinet ministers.

Despite this progress, however, there are still some challenges that women and non-binary folks face in these roles. They may face discrimination or prejudice from others who believe that women or non-binary individuals are not suited for positions of power or leadership. There may also be a tendency to view their actions and decisions through a lens of gender stereotypes or biases, which can affect how they are perceived and treated by others in political settings.

However, as more women and non-binary individuals assume leadership roles, there is a growing recognition of their ability to lead effectively and make significant contributions to society. Over time, this can help to shift societal attitudes and perceptions about gender and leadership, paving the way for greater gender equality in politics and other public roles.

which of the following choices gives the amount of power used by a capacitor in an ac circuit? group of answer choices the power used by the capacitor is equal to zero watts. vrmsirms2 irmsxc irmsxc2 vrmsxc

Answers

The power used by a capacitor in an AC circuit is equal to zero watts. Option 3 is correct.

This is because the power used by a capacitor is reactive power, which means that it is not dissipated as heat but is rather stored and released in the circuit. In an AC circuit, the capacitor alternately charges and discharges as the voltage and current change direction, respectively, but the net power used over a complete cycle is zero.

The other choices refer to different formulas for calculating other aspects of an AC circuit, such as the impedance of a capacitor (IrmsXC), the product of the voltage and the impedance (VrmsXC), or the total power in the circuit (VrmsIrms^2). However, none of these formulas give the amount of power used by a capacitor in an AC circuit. Option 3 is correct.

The complete question is

Which of the following choices gives the amount of power used by a capacitor in an ac circuit?

1. IrmsXC^2

2. IrmsXC

3. The power used by the capacitor is equal to zero watts.

4. VrmsXC

5. VrmsIrms^2

To know more about the Capacitor, here

https://brainly.com/question/15088605

#SPJ4


_______ assisted Anton Raphael Mengs with the iconography of his ceiling fresco, Parnasus, in the Villa Albani.

A) Johann Winckelmann
B) Cardinal Albani
C) Jacques Louis David
D) Joshua Reynolds

Answers

A johann winckelmann

A small block sits at one end of a flat board that is 4.00 m
long. The coefficients of friction between the block and the board are μs
= 0.550 and μk
= 0.400. The end of the board where the block sits is slowly raised until the angle the board makes with the horizontal is α0
, and then the block starts to slide down the board.

Answers

The block will slide down the board with an acceleration of 0.426 m/s^2 when the board is at an angle of 30 degrees.

To solve this problem

We can solve this problem using the concepts of static and kinetic friction, and the relationship between force, mass, and acceleration.

The maximum angle α0 at which the block remains stationary is given by the equation:

tan(α0) = μs

Where μs is the coefficient of static friction.

We can solve for α0 as:

α0 = tan^-1(μs) = tan^-1(0.550) = 29.0 degrees

When the angle of the board is greater than α0, the block will begin to slide down the board. The force of friction acting on the block will change from static friction to kinetic friction. The force of friction is given by:

Ff = μk * Fn

Where

μk is the coefficient of kinetic friction Fn is the normal force acting on the block

The normal force is equal to the weight of the block, which is given by:

Fn = mg

Where

m is the mass of the blockg is the acceleration due to gravity (9.81 m/s^2)

We can now calculate the force of friction as:

Ff = μk * Fn = μk * mg

Once the block begins to slide down the board, the acceleration of the block is given by:

a = (sin(α) - μk*cos(α)) * g

Where α is the angle of the board with respect to the horizontal. We can solve for α by setting the force of friction equal to the component of the weight of the block acting parallel to the board:

Ff = m * g * sin(α) = m * a

Substituting Ff and solving for α, we get:

sin(α) = (μk*cos(α) + a/g)

Using the given values of μk and the length of the board, we can calculate the acceleration of the block for a given angle α. For example, if we set α = 30 degrees, we get

a = (sin(30) - μkcos(30)) * g = (0.5 - 0.4sqrt(3)/2) * 9.81 m/s^2 = 0.426 m/s^2

Therefore, the block will slide down the board with an acceleration of 0.426 m/s^2 when the board is at an angle of 30 degrees.

Learn more about kinetic friction here : brainly.com/question/20241845

#SPJ1

two riders on bicycles, 100 miles apart. o each of these series. o begin traveling toward each other at the same time, one traveling at 10 miles a) acbdfe gal per hour and the other at is miles per hour. a fly named paul revere begins b) b~dwf fly~ng between the bicycles, starting from the front wheel of the slower c) h~f~dc~ beycle. if the fly travels at 20 miles per hour flying back and forth between 2 adam dropped a rubber ball from a bicycles, being able to reverse o window 40 feet above the sidewalk. directions without losing any time. how the ball always bounces half of the far will paul revere travel before the height that it drops. how far will the ball bicycles meet?

Answers

Paul Revere will travel a distance of 80 miles before the bicycles meet, and the rubber ball will bounce a distance of 20 feet.

First, we need to find the time it takes for the bicycles to meet. Using the formula d = rt, we can find that:

time = distance / rate

time = 100 miles / (10 mph + 15 mph)

time = 4 hours

During this time, Paul Revere will fly back and forth between the bicycles at a speed of 20 mph, so the total distance he travels will be:

distance = speed x time

distance = 20 mph x 4 hours

distance = 80 miles

Therefore, Paul Revere will travel a distance of 80 miles before the bicycles meet.

Next, we can find how far the rubber ball will bounce. Since the ball always bounces half the height that it drops, we can use the formula:

distance = initial height / 2

distance = 40 feet / 2

distance = 20 feet

Therefore, the ball will bounce a distance of 20 feet.

To know more about bicycle, here

brainly.com/question/13795395

#SPJ4

--The complete question is, Two riders on bicycles, 100 miles apart, begin traveling towards each other at the same time, one traveling at 10 miles per hour and the other at 15 miles per hour. A fly named Paul Revere begins flying between the bicycles, starting from the front wheel of the slower bicycle. If the fly travels at 20 miles per hour flying back and forth between the bicycles, how far will Paul Revere travel before the bicycles meet? Also, Adam dropped a rubber ball from a window 40 feet above the sidewalk. How far will the ball bounce if it always bounces half of the height that it drops?--

Two blocks of masses 1. 0 kg and 2. 0 kg, respectively, are pushed by a constant applied force f across a horizontal frictionless table with constant acceleration such that the blocks remain in contact with each other, as shown above. The 1. 0 kg block pushes the 2. 0 kg block with a force of 2. 0 n. The acceleration of the two blocks is.

Answers

The acceleration of the two blocks is approximately [tex]0.67 m/s^2.[/tex]

Since the two blocks are in contact and moving together, they are considered as a single system.

The net force on the system is the force applied to the 1.0 kg block minus the force of friction between the two blocks. According to Newton's second law, the net force is equal to the mass of the system times its acceleration:

Net force = (mass of system) x (acceleration)

We can set up an equation for the net force as follows:

Net force = F - f

where F is the applied force, and f is the force of friction between the two blocks. Since the table is assumed to be frictionless, there is no frictional force, so f = 0.

Therefore, the net force is simply equal to the applied force F:

Net force = F

We can now substitute the values given in the problem:

F = 2.0 N (the force applied to the 1.0 kg block)

m = 1.0 kg + 2.0 kg = 3.0 kg (the total mass of the system)

Using the equation for the net force, we can find the acceleration of the system:

Net force = (mass of system) x (acceleration)

F = m x a

a = F / m

a = 2.0 N / 3.0 kg

[tex]a =0.67 m/s^2[/tex]

To know more about acceleration refer here

https://brainly.com/question/12550364#

#SPJ11

(b) The aluminium wire will break if the tension in the wire exceeds 350N.


The wire is attached to the flagpole at B, 0. 8 m from the wall.


The wire is at an angle of 20° to the flagpole.


Assess whether the wire will break. You should use the principle of moments, taking


moments about 0.


length of flagpole = 1. 2m


mass of flagpole and flag = 15 kg

Answers

The wire won't break because the tension is less than 350N. To assess whether the wire will break, we need to calculate the tension in the wire using the principle of moments to do this, taking moments about point 0.

First, we need to calculate the weight of the flagpole and flag. We know that mass = 15 kg, so we can use the formula weight = mass x gravity, where gravity = 9.8 m/s^2. Therefore, weight = 15 x 9.8 = 147 N.

Next, we need to calculate the force exerted by the wire. We can use trigonometry to find the horizontal and vertical components of this force. The horizontal component is given by F_h = F x cos θ, where F is the tension in the wire and θ is the angle between the wire and the flagpole. In this case, F_h = F x cos 20°.

The vertical component is given by F_v = F x sin θ. In this case, F_v = F x sin 20°.

Now, we can take moments about point 0. The weight of the flagpole and flag acts vertically downwards at a distance of 0.8 m from point 0, so its moment is 147 x 0.8 = 117.6 Nm (clockwise).

The force exerted by the wire acts at an angle of 20° to the flagpole, so its horizontal component acts perpendicular to the flagpole and its vertical component acts parallel to the flagpole. The horizontal component has no moment about point 0, so we only need to consider the vertical component. This acts at a distance of 1.2 m from point 0, so its moment is F_v x 1.2 (anticlockwise).

Setting the moments equal to each other, we get:

147 x 0.8 = F_v x 1.2 x  sin 20°

Simplifying this equation, we get:

F_v = 78.7 N

To find the tension in the wire, we can use Pythagoras' theorem:

F = √(F_h^2 + F_v^2) = √((F x cos 20°)^2 + 78.7^2)

Simplifying this equation, we get:

F = 87.6 N

Since the tension in the wire is less than 350N, the wire will not break.

Know more about Tension here:
https://brainly.com/question/30470948

#SPJ11

A 0. 068-kg ball strikes a wall with a velocity of 22. 1 m/s. The wall stops the ball in 0. 63 s. What is the magnitude of the
force applied by the wall on the ball?

a. 5. 3n
b. 4. 2n
c. 12n
d. 2. 4n

Answers

The correct answer is (d) 2.4 N. We can use the impulse-momentum theorem to solve this problem. The impulse of the force is equal to the change in momentum of the ball.

The initial momentum of the ball is: p1 = mv = (0.068 kg)(22.1 m/s) = 1.5038 kg*m/s

Since the wall stops the ball, the final momentum of the ball is zero: p2 = 0 kg*m/s

The change in momentum is: Δp = p2 - p1 = -1.5038 kg*m/s

The time interval for the force to act is 0.63 s.

So, the magnitude of the force applied by the wall on the ball is: F = Δp / Δt = (-1.5038 kg*m/s) / (0.63 s) ≈ 2.4 N

Therefore, the correct answer is (d) 2.4 N.

To know more about impulse-momentum, refer here:

https://brainly.com/question/904448#

#SPJ11

Which one of the following instrument is most suitable for measuring thickness of

the physics book?

A. Meter rule ⃝ B. Vernier calipers ⃝

C. Measuring tape ⃝ D. Screw gauge ⃝

Answers

The most suitable instrument for measuring the thickness of a physics book is B. Vernier calipers, as they provide a higher degree of accuracy and precision compared to the other options.

One of the key advantages of Vernier calipers is their ability to provide measurements with a high level of precision. The Vernier scale allows for measurements to be read to a fraction of the smallest division on the main scale, significantly increasing the accuracy of the measurement.

This is especially useful when dealing with objects that have small dimensions or require precise measurements, such as the thickness of a book.

Furthermore, Vernier calipers often have a fine adjustment mechanism that enables the user to ensure a tight fit around the object being measured, minimizing any potential errors due to play or movement. This feature contributes to the overall accuracy of the measurements.

In comparison to other measuring instruments, such as a ruler or a tape measure, Vernier calipers provide a greater level of precision. Rulers, for example, typically have larger increments and are better suited for measuring longer distances rather than small thicknesses.

Tape measures, on the other hand, can be flexible and might not provide the same level of accuracy as Vernier calipers, especially when measuring thin objects.

To learn more about calipers, refer below:

https://brainly.com/question/13522392

#SPJ11

Do the Pressure vs. Depth Lab (record Describe how the distance the water
your activity)

•When will the water flow out the farthest: when the water is nearly full, half-full, or nearly empty?

•Hold the bottle over the bucket so that the water will flow out the hole into the bucket and loosen the bottle cap.
Observe the flow of water. PUT THE CAP BACK ON!

•Describe how the distance the water flowed out changed as the depth of the water changed.

fill in the blanks
•The pressure of a fluid _____ as depth increases. So pressure and depth are _____ proportional.
This can be written as _____

Answers

Pressure vs. Depth Lab:

The water will flow out the farthest when the bottle is nearly full.As the depth of the water increased, the distance the water flowed out also increased.The pressure of a fluid increases as depth increases. So pressure and depth are directly proportional.This can be written as P ∝ d, where P is pressure and d is depth.

What is pressure?

Pressure is defined as the force per unit area applied on an object. It is a scalar quantity, which means it only has magnitude and no specific direction.

It is often measured in units of Pascals (Pa), which is equivalent to one Newton of force per square meter of area. Pressure can be caused by the weight of an object, the force applied by a fluid, or the collision of particles with a surface.

Find out more on pressure here: https://brainly.com/question/28012687

#SPJ1

On a planet other than earth, the acceleration due to gravity is more than on earth. if you float in water on this planet, you would
a. find it easier to float on earth.
b. harder to float on earth.
c. same effort to float on earth
d. you would sink on earth
e. have a greater buoyant force on earth

Answers

The buoyant force experienced by an object immersed in a fluid is given by the equation:

Buoyant force = (Density of fluid) x (Volume of fluid displaced) x (Acceleration due to gravity)

Since the density of water is constant, the only factor that changes when we compare floating in water on different planets is the acceleration due to gravity.

If the acceleration due to gravity is more on the other planet, then the buoyant force experienced by the object will also be more compared to the buoyant force experienced on Earth, given the same volume of fluid displaced. Therefore, the object would find it easier to float on the other planet than on Earth.

So the correct answer is: a. find it easier to float on earth.

To know more about buoyant force refer here

https://brainly.com/question/20165763#

#SPJ11

Co-efficient of volume expansion of
aluminium

Answers

The coefficient of volume expansion of a material is a measure of how much its volume changes with a change in temperature. For aluminium, the coefficient of volume expansion is approximately [tex]7.1 \times 10^{-5}[/tex] per degree Celsius ([tex]K^{-1}[/tex]).

For aluminium, the coefficient of volume expansion is approximately [tex]23.1 \times 10^{-6}[/tex] per degree Celsius. This means that for every degree Celsius increase in temperature, the volume of aluminium will increase by approximately 23.1 parts per million (ppm).

This coefficient of volume expansion is an important property of aluminium, as it affects its behaviour in a variety of applications. For example, in the aerospace industry, aluminium is used extensively in the construction of aircraft because of its low weight and high strength-to-weight ratio. However, as the temperature of the aircraft changes during flight, the volume of the aluminium components will also change, potentially affecting the structural integrity of the aircraft.

Understanding the coefficient of volume expansion is therefore essential for engineers and designers working with aluminium in a variety of fields, from aerospace to construction to electronics.

To learn more about volume expansion

https://brainly.com/question/31456049

#SPJ4

A cannonball is fired horizontally from the top of a cliff. The cannon is at height H = 70.0 m above ground level, and the ball is fired with initial horizontal speed v0 . Assume acceleration due to gravity to be g = 9.80 m/s2 .

A)Assume that the cannon is fired at time t=0 and that the cannonball hits the ground at time tg . What is the y position of the cannonball at the time tg/2 ? Answer numerically in units of meters.

Answers

The vertical position of the cannonball at the time tg/2 is 87.5 meters above ground level.

What is the vertical position of the cannonball?

The horizontal motion of the cannonball is independent of its vertical motion. Since the cannonball is fired horizontally, its initial vertical velocity is zero, and it only experiences a downward acceleration due to gravity.

We can use the following kinematic equation to determine the time it takes for the cannonball to hit the ground:

h = v₀_y * t + (1/2) * g * t²,

where;

h is the initial height of the cannonball, v₀_y is the initial vertical velocity of the cannonball (which is zero), and t is the time it takes for the cannonball to hit the ground.

Solving for t, we get:

t = √(2*h/g)

Plugging in the given values, we get:

t = √(2*70/9.8) = 3.78 s

Therefore, the cannonball hits the ground at time t = 3.78 s.

Now, let's consider the vertical motion of the cannonball. At the time tg/2, the time elapsed since the cannon was fired is tg/2.

The vertical position of the cannonball at this time can be calculated using the following kinematic equation:

y = h + v₀_y * t + (1/2) * g * t²,

Since v₀_y is zero, we have:

y = h + (1/2) * g * (tg/2)²

Plugging in the given values, we get:

y = 70 + (1/2) * 9.8 * (3.78/2)² = 87.5 m (rounded to one decimal place)

Learn more about vertical position here: https://brainly.com/question/21026296

#SPJ1

which statement must be true for a rocket to travel from earth to another planet? group of answer choices it must have large engines. it must attain escape velocity from earth. it must carry a lot of extra fuel. it must be launched from space, rather than from the ground.

Answers

For a rocket to travel from Earth to another planet, it must attain escape velocity from Earth. Option B is correct.

This is the minimum velocity needed to escape the gravitational pull of Earth and enter into space. Once a rocket achieves escape velocity, it can continue on its trajectory toward the other planet without the need for extra fuel or engines. While having large engines and carrying extra fuel can certainly be beneficial for a rocket's journey, they are not absolute requirements for traveling from Earth to another planet.

Additionally, launching from space rather than from the ground is not a requirement, as many successful missions have been launched from Earth's surface. Therefore, the key requirement for a rocket to travel from Earth to another planet is to attain escape velocity from Earth's gravitational pull. Option B is correct.

To know more about the Rocket, here

https://brainly.com/question/10488794

#SPJ4

Suppose you can jump 1 m on earth. how high would you be able to jump on
mars? the mass of mars is 6.4181023kg and its radius is 3.38106m.

Answers

To determine how high you would be able to jump on Mars compared to Earth, we can use the concept of gravitational potential energy.

On both Earth and Mars, the gravitational potential energy (PE) is given by the equation:

PE = mgh

where m is your mass, g is the acceleration due to gravity, and h is the height.

The acceleration due to gravity can be calculated using Newton's law of universal gravitation:

g = (G * M) / (r^2)

where G is the gravitational constant, M is the mass of the celestial body (in this case, Mars), and r is the distance from the center of the celestial body to the surface (in this case, the radius of Mars).

Let's assume your mass is the same on both Earth and Mars.

On Earth, the acceleration due to gravity (g_Earth) is approximately 9.8 m/s^2, and the height (h_Earth) is 1 m.

PE_Earth = m * g_Earth * h_Earth

On Mars, we need to calculate the acceleration due to gravity (g_Mars) using the given mass and radius of Mars. The gravitational constant (G) is approximately 6.67430 × 10^(-11) m^3/(kg s^2).

g_Mars = (G * M) / (r^2)

g_Mars = (6.67430 × 10^(-11) m^3/(kg s^2) * 6.418 * 10^(23) kg) / (3.38106 m)^2

Now we can calculate the height (h_Mars) you would be able to jump on Mars:

PE_Mars = m * g_Mars * h_Mars

Since we are assuming the same mass on both Earth and Mars, we can set the potential energies on Earth and Mars equal to each other and solve for h_Mars:

m * g_Earth * h_Earth = m * g_Mars * h_Mars

h_Mars = (g_Earth / g_Mars) * h_Earth

Now we can substitute the values and calculate the height you would be able to jump on Mars:

h_Mars = (9.8 m/s^2 / g_Mars) * 1 m

To know more about potential energy refer here

https://brainly.com/question/14294569#

#SPJ11

If charge X has a magnitude of 5x10^-9 C, charge Y would have


an approximate charge of ____________________ C

Answers

Assuming charge Y has the same magnitude as charge X (5x10^-9 C), the approximate charge of Y would also be 5x10^-9 C.

In this assumption, we are considering that charge Y has the same magnitude as charge X, which is 5x10^-9 C. This means that both charges carry the same amount of electric charge. The notation "C" represents coulombs, which is the unit of electric charge.

By assuming that charge Y has the same magnitude as charge X, we are implying that both charges are equal in strength but may have opposite polarities.

Charges can either be positive or negative, and their interactions depend on their polarity. If charge X is positive, then charge Y would also be positive in order for them to have the same magnitude. Similarly, if charge X is negative, then charge Y would also be negative.

It's important to note that this assumption is based on the given information and does not take into account any specific context or additional factors that may affect the charges.

In real-world scenarios, the charges of different objects or particles can vary, and their interactions depend on various factors such as distance, medium, and other electric fields present in the surroundings.

Therefore, the approximate charge of Y is 5x10^-9 C, assuming that it has the same magnitude as charge X.

To learn more about magnitude, refer below:

https://brainly.com/question/14452091

#SPJ11

The resistance in a series rcl circuit is doubled. (a) does the resonant frequency increase, decrease, or remain the same

Answers

The resonant frequency will also remain the same.

The resonant frequency of a series RLC circuit is given by the formula f = 1/(2π√(LC)), where L is the inductance of the circuit, C is the capacitance of the circuit, and π is a mathematical constant approximately equal to 3.14.

Doubling the resistance in the circuit will not change the inductance or capacitance, so these values will remain the same.

Therefore, the resonant frequency will also remain the same.

In other words, the circuit's ability to store and transfer energy at its resonant frequency will not be affected by the change in resistance.

To know more about resonant frequency, refer here:

https://brainly.com/question/28168823#

#SPJ11

On its highest power setting, a certain microwave oven projects 1.00kW of microwaves onto a 30.0 by 40.0 cm area. (A) what is the intensity in W/m^2 ? (B) calculate the peak electric field srength E0 in these waves. (C) what is the peak magnetic field strength B0?we use the equation I=P/A. which gives us the answer 8.33 * 10^3 W/m^2 and then moves on to give us 2I average = 1.67 * 10^4.i dont understand how they got the 2Iave=1.67×10^4

Answers

On its highest power setting, a certain microwave oven projects 1.00kW of microwaves onto a 30.0 by 40.0 cm area. Intensity is 8.33 × 10^3 W/m^2, Peak electric field strength is 4.84 × 10^4 V/m, Peak magnetic field strength is 1.61 × 10^-4 T

(A) To find the intensity (I) in W/m^2, we use the formula I = P/A, where P is power and A is area.

Power (P) = 1.00 kW = 1000 W
Area (A) = 30.0 cm × 40.0 cm = 0.3 m × 0.4 m = 0.12 m^2
I = P/A = 1000 W / 0.12 m^2 = 8.33 × 10^3 W/m²

(B) The average intensity (I_average) is related to the peak electric field strength (E0) by the formula:
I_average = (1/2) × ε0 × c × E0^2
where ε0 is the vacuum permittivity (8.85 × 10^-12 C^2/N·m^2), c is the speed of light (3 × 10^8 m/s), and E0 is the peak electric field strength.
To find the peak electric field strength, first, we'll rearrange the formula to isolate E0:
E0^2 = (2 × I_average) / (ε0 × c)
E0 = sqrt((2 × I_average) / (ε0 × c))
Now, let's plug in the values:
E0 = sqrt((2 × 8.33 × 10^3 W/m^2) / (8.85 × 10^-12 C^2/N·m^2 × 3 × 10^8 m/s))
E0 ≈ 4.84 × 10^4 V/m

(C) To find the peak magnetic field strength (B0), we use the formula:

B0 = E0 / c
B0 = (4.84 × 10^4 V/m) / (3 × 10^8 m/s)
B0 ≈ 1.61 × 10^-4 T

Learn more about microwave oven here:-

https://brainly.com/question/29944171

#SPJ11

For what values of h and k does the linear system have infinitely many solutions?.

Answers

A linear system of equations has infinitely many solutions when the equations are dependent, meaning that one equation can be obtained by scaling or combining the other equations. In general, this occurs when the equations represent parallel lines or overlapping lines.

Consider a linear system of two equations:

Equation 1: ax + by = c

Equation 2: dx + ey = f

If these equations have infinitely many solutions, it means that the slopes of the lines represented by the equations are equal (a/b = d/e) and the y-intercepts are also equal (c/b = f/e).

Therefore, for the linear system to have infinitely many solutions, the coefficients of x and y in the equations must be proportional and the constants on the right side of the equations must also be proportional.

In terms of the variables h and k:

Equation 1: hx + ky = c1

Equation 2: dx + ey = c2

For the system to have infinitely many solutions, the coefficients h and d must be proportional (h/d = k/e) and the constants c1 and c2 must be proportional (c1/d = c2/e).

This condition can be simplified to:

h/d = k/e

So, for the linear system to have infinitely many solutions, h and k must be proportional to the respective coefficients d and e.

To know more about linear system refer here

https://brainly.com/question/26544018#

#SPJ11

Other Questions
I need help finding the answers to questions 1 through 9 PLEASE HELP IVE BEEN TAKING THIS MATH TEST FOR 5 HOURSA 154-lb person burns 420 calories per hour riding an exercise bicycle at a rate of 15 mi/hr. Write a function rule to represent the total calories burned over time by that person. Explain how the information in the problem relates to the function. Commercial banks can create money by(A) transferring depositors' accounts at the Federal Reserve for conversion to cash(B) buying Treasury bills from the Federal Reserve(C) sending vault cash to the Federal Reserve(D) maintaining a 100 percent reserve requirement(E) lending excess reserves to customers Declan is grocery shopping and notes that there are nutritional facts labels on most of the products he has in his shopping cart. he picks up a pack of salmon fillets but cannot find nutritional facts listed. which best explains the reason declans fish is missing the nutrition label? a. an employee in the seafood department forgot to include the label. b. fish do not weigh the same so it would be hard to calculate facts for each. c. the fda only requires nutritional facts labels on snack foods or canned items. d. because salmon is a refrigerated item, the fda does not require a nutrition label. During an excursion, an archeologist finds an ecologically important area. which organization should the archeologist approach to conserve the land? Is the triangle similar to PQR? State whether each triangle similar to PQR by answering yes or no how is loudness different from intensity One hundred kilograms of an aqueous solution of p-chlorophenol at a concentration of 1 g per kgwater is to be treated with 2 kg of an adsorbent to recover the compound from the solution by a twostage crosscurrent contact. calculate the maximum percentage recovery of the solute if theequilibrium relation at the operating temperature of 298k is given by: = . where x = kg solute (p-chlorophenol) per 1000 kg water and y = kg solute per kg adsorbent What produces electricity from a chemical reaction and cannot be run in reverse Maggie places cells of Elodea, a freshwater plant, on a wet-mount microscope slide. She uses a saltwater solution to prepare the slide. When she observes the cells under the microscope, what is she most likely to see?A. The cell walls have dissolved, releasing the cell. B.The cells have remained unchanged. C.The cells will swollen, expanding the cell walls. D.The cells have shrunk within the cell walls. Discuss the presentation of the cat in the following poem.Consider the writer's choice of language, imagery and structure in your answer. What is the molarity of the solution made by dissolving 15.1 g of solid naf in water and diluting it to a finalvolume of 550.0 ml? Question 28(1 mark)Two other minerals can be seen in the photo:galena, a dark grey mineral with the formula PbSiron pyrite, a gold-coloured mineral with the formula FeS2Compare their chemical formulas, by writing down one similarity and one difference between these two minerals.Note: Pb = lead, Fe = iron, S = sulfur.Question 29(1 mark)Wanting to create the beautiful golden colour of iron pyrite, FeS2, in the lab, a student mixes together black powdered iron (Fe) and yellow powdered sulfur (S). The result is a dull, yellowish grey powder. Propose why this attempt failed?Question 30(1 mark)The student can vary the proportions of iron and sulfur by adding more of each powder to the mixture. Clarify why the same thing isn't true for the compound iron pyrite. What is one way secondary succession differs from primary succession?answer choicesA. Secondary succession is typically quicker than primary successionB. Secondary succession is typically slower than primary successionC. Secondary succession only occurs in mountains, primary succession only occurs in wetlandsD. Secondary succession is the gradual change in plant species, while primary succession is the gradual change in animal species PLease help 1 and 2 Pythagorean Theorem and if you can explain please In not less than 500 words worie astory endingwith the statemed it pays to tell the truth The function f(x) = 2x + 7x{-1} has one local minimum and one local maximum. This function has a local maximum at x = with value and a local minimum at x = with value A magazine listed the number of calories and sodium content (in milligrams) for 13 brands of hot dogs. Examine the association, assuming that the data satisfy the conditions for inference. Complete parts a and b On Friday, Jacob planted a pinto bean in science class. When he returned to school on Monday, the bean had sprouted a stem that was 3 millimeters long. At the end of the week, Jacob's bean sprout had a stem that was 42 millimeters long. How many centimeters did Jacob's bean sprout grow during the week? AH = Actual Hours SH = Standard Hours AR = Actual Rate SR = Standard Rate Compute the direct labor rate and efficiency variances for the period and classify each as favorable, unfavorable or no variance