a. The convection heat transfer coefficient for a similar bar with L = 1 m when V = 15 m/s is 0.7756.
b. The the convection heat transfer coefficient for a similar bar with L=1 m when V = 30 m/s is 34.24W/m²K.
c. The convective coefficient is 58.6W/m²K.
How to calculate the valuesConsider the correlation for Nusselt's number.
Nu= C Re" Pr"
hL k VL = Pr"
Here, k is thermal conductive coefficient, v is the viscosity, and Pr is the Prandtl number.
Following parameter will remain unchanged:
k, L, Pr, C, v, m, and n.
Calculate the ratio of Nusselt's numbers,
Nu hL VL
= Nu h = VL
50 40 20×0.5 15×0.5
1.25 = 20 15
m=0.7756
Part (b)
Calculate the convective coefficient. 0.7756
hL h₂L₂ VL VL2
h=50x 0.5 15×1 1 20×0.5 0.7756
h=34.24 W/m² K
Part (c)
Calculate the convective coefficient.
h, L, = VL
h=50x 0.5 30×1 1 20×0.5 0.7756.
h=58,6 W/m2 K
Part (d) When characteristics length is taken as a side instead of diagonal. the value of constant C will change. But result will not change.
Learn more about Correlation on
https://brainly.com/question/28175782
#SPJ4
Which cast-in-place concrete systems are the easiest to penetrate with large holes?
Cast-in-place concrete systems refer to the process of pouring and setting concrete at the construction site, as opposed to precast systems, where concrete is produced off-site and transported to the location. When it comes to penetrating large holes, the easiest cast-in-place concrete systems to work with are those with lower concrete strength and higher porosity.
For example, lightweight concrete or cellular concrete would be easier to penetrate due to their lower density and higher porosity compared to regular or high-strength concrete. These materials have a less compact structure, allowing for easier drilling or cutting to create large holes.
To penetrate a cast-in-place concrete system with large holes, follow these steps:
1. Identify the type of concrete system (e.g., lightweight or cellular concrete).
2. Select the appropriate tools for penetration, such as a core drill or concrete saw.
3. Mark the location and size of the hole on the concrete surface.
4. Set up the drilling or cutting equipment, ensuring proper safety precautions are in place.
5. Begin the penetration process, applying steady pressure and maintaining control of the tool.
6. Remove the cut or drilled material from the hole and clean the area.
7. Inspect the hole for accuracy and make any necessary adjustments.
Remember that proper safety measures, such as wearing protective gear and using the correct equipment, are essential when working with cast-in-place concrete systems.
to know more about concrete:
https://brainly.com/question/28903866
#SPJ11
What type of development model(s) allow users to select the make and model of the mobile device?
The type of development model that allows users to select the make and model of the mobile device is typically the agile development model. This model emphasizes frequent iterations and customer involvement throughout the development process, allowing for flexibility and adaptation to changing user needs. Additionally, user-centered design principles are often incorporated into agile development to ensure that the mobile application is optimized for the specific make and model of device being used.
Recognition of multiple racial identities: Multiracial identity development models recognize that individuals may identify with more than one racial group and may experience unique challenges in reconciling their multiple identities. In contrast, monoracial identity development models typically assume a single racial identity and do not address the experiences of individuals with multiple racial identities.
To know more about development model
https://brainly.com/question/10560579?
#SPJ11
7. In the absence of a specific designee, the ____ shall be considered the Impairment Coordinator?
(Designee) a person who has been designated.
In the absence of a specific designee, the chief engineer or equivalent position shall be considered the Impairment Coordinator.
The Impairment Coordinator is responsible for coordinating and overseeing the procedures related to the temporary shutdown or impairment of fire protection and life safety systems, equipment, or devices in a building or facility.
The Impairment Coordinator ensures that appropriate measures are taken to maintain the level of fire and life safety during the temporary shutdown or impairment, and that all affected parties are notified of the situation and the procedures that will be followed.
Learn more about designee, here
https://brainly.com/question/30038926
#SPJ4
The driving force for a diffusion process that is described by Fick's first law is the:
concentration gradient. Fick's first law of diffusion states that the rate of diffusion of a substance through a medium is directly proportional to the concentration gradient of that substance.
In other words, the driving force behind the diffusion process is the difference in concentration between two regions, with the substance moving from an area of high concentration to an area of low concentration. The greater the concentration gradient, the faster the diffusion rate. This principle is commonly used to describe various diffusion processes in physics, chemistry, and biology, such as the movement of gases in and out of cells, the spread of pollutants in the environment, and the release of aroma from food.
learn more about diffusion here:
https://brainly.com/question/20843145
#SPJ11
5. Pipes filled with water or compressed air, and equipped with automatic devices are called.
Pipes filled with water or compressed air and equipped with automatic devices are called "fire sprinkler systems".
Fire sprinkler systems are designed to detect and respond to fires in their early stages by discharging water or other extinguishing agents onto the affected area to control or extinguish the fire.
The automatic devices in the sprinkler system, known as sprinkler heads, are designed to open and release water or other extinguishing agents when the temperature in the area exceeds a predetermined threshold.
The water or other agent is then distributed through a network of pipes and delivered to the affected area, helping to control or extinguish the fire.
Learn more about "fire sprinkler systems", here
https://brainly.com/question/30777999
#SPJ4
Bytecode is understood, and executed, by a Java interpreter, called a _______ _______ _______.
Hi! Your question is: Bytecode is understood, and executed, by a Java interpreter, called a _______ _______ _______.
My answer: Bytecode is understood, and executed, by a Java interpreter, called a Java Virtual Machine (JVM).
Learn more about Java interpreter: https://brainly.com/question/31561197
#SPJ11
Transfers files with a remote host (typically requires authentication of user credentials) (Wallace 52)
Transferring files with a remote host is a common practice in today's digital age, especially with the increasing use of cloud-based storage solutions. This process typically requires authentication of user credentials, ensuring that only authorized users can access and transfer files.
The authentication process involves providing login credentials such as a username and password or a public and private key combination. Once authenticated, users can transfer files securely between the remote host and their local machine.There are several ways to transfer files with a remote host, including using File Transfer Protocol (FTP), Secure Copy (SCP), and Secure File Transfer Protocol (SFTP). FTP is a standard protocol used to transfer files between two computers on the internet, while SCP and SFTP are secure alternatives that encrypt data during transfer. SFTP is preferred over FTP because it provides secure data transfer through an encrypted SSH tunnel.Regardless of the method used, it is important to ensure that the remote host is secure and that proper security measures are in place to protect against unauthorized access. This includes using strong passwords, enabling two-factor authentication, and regularly updating software and security patches.In summary, transferring files with a remote host is a crucial process that requires proper authentication of user credentials. Using secure transfer protocols such as SFTP and implementing proper security measures can help ensure that data is transferred safely and securely between the remote host and local machine.For such more question on protocol
https://brainly.com/question/28811877
#SPJ11
Template functions may also have reference parameters. Write the function template consume which reads a value from standard input, and returns the value. Complete the following file: consumer. H #ifndef CONSUMER_H #define CONSUMER_H #include 1 2. 3 4 5 6 7 8 // Add your function template here #endif Submit Use the following file:
Demo. Cpp #include
#include #include #include using namespace std; #include "consumer. H" int main() { int a; cout << consume(a) * 2 << endl; double b; cout << sqrt(consume(b)) << endl; string s; cout << consume(s). Size() << endl; }
The template function when completed is
template <typename my_value>
my_value& consume(my_value& x) {
cin>>x;
return x;
}
Completing the template functionFrom the question, we have the following parameters that can be used in our computation:
The incomplete function from the question the following definitions:
#include #include #include
using namespace std;
#include "consumer. H"
int main() {
int a;
cout << consume(a) * 2 << endl;
double b;
cout << sqrt(consume(b)) << endl;
string s;
cout << consume(s). Size() << endl;
}
To complete the template function, we write the following coed segment which accepts an input value x and retuns it back to the user
The templaete function would call the consume method defined in the main function
Note that template functions begin with the definiton template <typename variable>
So, we have
template <typename my_value>
my_value& consume(my_value& x) {
cin>>x;
return x;
}
Read more about code segments at
https://brainly.com/question/26497128
#SPJ1
What is most likely the situation if a pilot asks for an OROCA?
If a pilot asks for an OROCA (Off-Route Obstacle Clearance Altitude), it is most likely because they are flying off-route or outside of designated airspace and want to ensure they have a safe altitude that will keep them clear of any potential obstacles or terrain. This could be due to weather conditions, traffic congestion, or other factors that require them to deviate from their original flight plan. By requesting an OROCA, the pilot is taking proactive measures to ensure their safety and the safety of their passengers while navigating through unfamiliar or unpredictable airspace.
To know more about OROCA
https://brainly.com/question/14253823?
#SPJ11
When shall measurements be taken to verify tolerances of reconstructed tanks?
A) After hydrostatic testing
B) Before hydrostatic testing
C) After lay out of all plates
D) After fit-up and tack welding used for alignment purposes
D) After fit-up and tack welding used for alignment purposes.
Measurements should be taken after fit-up and tack welding to verify tolerances of reconstructed tanks before proceeding with further welding and hydrostatic testing. This ensures that the tank is aligned and within the verified tolerances before proceeding with further construction.
Learn more about verify tolerances: https://brainly.com/question/20066466
#SPJ11
What low level networking feature will facilitate a segmentation-based approach to containing intrusion events?
One low level networking feature that can facilitate a segmentation-based approach to containing intrusion events is VLAN (Virtual Local Area Network). By using VLANs, the network can be divided into multiple logical segments, each with its own set of access controls and security policies. This allows for better containment of intrusion events, as any compromised device will be isolated to its own segment, preventing lateral movement throughout the network. Additionally, VLANs can be configured to limit broadcast traffic, further enhancing security by reducing the attack surface.
To know more about VLAN
https://brainly.com/question/30770746?
#SPJ11
How does VSS assist a backup solution?
VSS, or Volume Shadow Copy Service, assists a backup solution in the following ways:
1. Creating point-in-time snapshots: VSS captures the state of a file system at a specific moment, allowing the backup solution to create a consistent backup without interrupting user activities or locking files.
2. Reducing backup time: By creating snapshots, VSS enables the backup solution to copy only changed data, rather than the entire file system, thus reducing the time needed to complete the backup process.
3. Minimizing data loss: VSS helps minimize data loss by ensuring that open files and applications are properly backed up, preserving the integrity of the data.
4. Simplifying data recovery: VSS makes it easier to restore individual files or entire volumes from a backup, as the snapshots represent consistent points in time that can be easily accessed and restored.
In summary, VSS assists a backup solution by creating consistent point-in-time snapshots, reducing backup time, minimizing data loss, and simplifying data recovery.
To know more about VSS
https://brainly.com/question/30893184?
#SPJ11
In the event of an alarm for fire in an Office building, who shall ascertain the location of the fire or cause?
A. Fire Brigade
B. Deputy Fire Safety Director
C. Fire Warden
D. The owner
In the event of an alarm for fire in an Office building, Fire Warden shall ascertain the location of the fire or cause. Thus, option C is the correct option.
The Fire Warden is responsible for determining where the fire is located and directing the evacuation of the floor in compliance with any instructions given and the following rules: The fire floor and the floors directly above it require quick evacuation more than any other places.
In conclusion, when the fire alarm goes off, it's crucial to maintain your composure and move promptly. Go to the appropriate assembly spot right away and exit the building. Avoid attempting to use the elevator, re-enter the building, or put out big fires.
Learn more about Fire Warden here:
https://brainly.com/question/20595654
#SPJ4
Nanomaterials may be metallic or ceramic but never polymeric. True or false?
False. Nanomaterials can be metallic, ceramic, polymeric, or even composite materials. The term "nanomaterials" refers to materials that have nanoscale dimensions,
typically with at least one dimension (such as length, width, or height) in the nanometer range (1-100 nanometers). These materials can exhibit unique properties and behaviors at the nanoscale due to their small size and high surface-to-volume ratio. Metallic nanomaterials can include nanoparticles, nanocomposites, and nanostructured materials made of metals or metal alloys, which can have enhanced properties such as improved electrical conductivity, increased strength, and unique optical properties. Ceramic nanomaterials can include nanoparticles, nanocomposites, and nanostructured materials made of ceramics, which can exhibit properties such as high hardness, high melting points, and excellent thermal stability. Polymeric nanomaterials are nanoscale materials made of polymers, which are large molecules made up of repeating units. Polymeric nanomaterials can have properties such as high flexibility, light weight, and biocompatibility, making them suitable for a wide range of applications including drug delivery, coatings, and sensors.
learn more about Nanomaterials here:
https://brainly.com/question/14910031
#SPJ11
here is a branched water distribution system: j-1 (x,y,z): 0,0,100 ft j-2 (x,y,z): 500,200,70 ft j-3 (x,y,z): 1000,200,50 ft j-1 is connected to j-2 and j-2 is connected to j-3. pressure at j-1 is 110 psi. all pipes are 6 inch with c value of 130. flow rate is 1 cfs in all pipes. analyze the system. what is pressure at j-3? use your calculator to solve this problem.
It should be noted that evidence implies that the pressure at J-3 is nearly ninety-eight point seven three psi.
How to explain the pressureTo begin, all pipes must be assigned with flow directions; therefore, let us presume the stream to progress from J-1 through J-2 and finish in J-3.
Consequently, an initial approximation of pressure at each connector can be initiated. Thus, we shall assume that J-2 has a pressure of one hundred psi and J-3 has ninety psi.
Moving forward, we can compute the head loss and quantity of air flowing in every pipe by utilizing the Darcy-Weisbach equation which reads as follows: hL = f * (L/D) * (V^2/2g) and Q = V * A. Taking into consideration the roughness coefficient of zero point one five times ten-to-the-negative-four foot and Colebrook's equation for calculating friction factor, the eventual pressure at junction three can be identified as about ninety-eight point seven three psi.
Therefore, evidence implies that the pressure at J-3 is nearly ninety-eight point seven three psi.
Learn more about pressure on
https://brainly.com/question/28012687
#SPJ4
Query the names of all the Japanese cities in the CITY table. The COUNTRYCODE for Japan is JPN.
To query the names of all the Japanese cities in the CITY table, you can use the SELECT statement in SQL. The COUNTRYCODE for Japan is JPN, which means you will need to use this code to filter out only the cities in Japan.
For such more question on criteria
https://brainly.com/question/1788910
#SPJ11
TRUE OR FALSE:
Linearizing circuit techniques are used for LEDs. State whether the given statement is true or false.
The given statement is true. Linearizing circuit techniques are used for LEDs.
LEDs are non-linear devices and their brightness and color output are not proportional to the input current. Thus, in order to obtain a linear relationship between the input current and the output brightness and color, linearizing circuit techniques such as feedback control, pulse-width modulation, and current regulation are used. These techniques allow for a consistent and accurate level of light output from the LED.
Therefore, the statement "Linearizing circuit techniques are used for LEDs" is true
Learn more about LEDs, here:
https://brainly.com/question/31586957
#SPJ4
9. At what temperature must any substance be raised to burn freely in air?
The combustible substances cannot catch fire as long as its temperature is lower than its ignition temperature. For example the ignition temperature of phosphorous is 35°C and that of petrol is 220°C.
The minimum temperature of a substance which is required to start or cause combustion is defined as the ignition temperature. The ignition temperature is also known as the ignition point.
So the ignition temperature represents the temperature at which any substance may catch fire and start burning freely in air. It is the lowest temperature at which an explosive atmosphere can ignite.
To know more about ignition temperature, visit;
https://brainly.com/question/7582375
#SPJ4
Following a loss of critical IP exfiltrated from the local network to a public cloud storage network, you decide to implement a type of outbound filtering system. Which technology is most suitable for implementing the filter?
The most suitable technology for implementing an outbound filtering system in this scenario would be a cloud access security broker (CASB). A CASB allows organizations to monitor and control access to cloud resources, including public cloud storage networks, from their local network. It can provide visibility into all cloud activity, enforce security policies, and prevent unauthorized access and data exfiltration. With a CASB in place, organizations can prevent future losses by monitoring and filtering all outbound traffic to public cloud storage networks.
To know more about CASB
https://brainly.com/question/29510369?
#SPJ11
fill in the blank. The Swedish soil scientist, _____developed a method of quantitatively describing the effect of soil moisture on the consistency of fine-grained soils.
Atterberg,
Answer:
Albert Atterberg
Explanation:
Swedish scientist Albert Atterberg was the first person to define the limits of soil consistency for the classification of fine-grained soils and later, they were refined by Arthur Casagrande.
What is the principal use of grep in relation to log files?
The principal use of grep in relation to log files is to search for specific patterns or keywords within the log files. Grep is a powerful command-line tool used for filtering and searching text. In the context of log files, grep allows you to extract relevant information, find errors, or identify specific events by searching for matching text patterns. Here's a step-by-step explanation:
1. Open a command-line interface or terminal on your computer.
2. Navigate to the directory containing the log files you want to search.
3. Use the "grep" command followed by the pattern or keyword you want to search for, and then specify the log file(s) as an argument. For example: `grep "error" logfile.txt`
4. Grep will display the lines in the log files containing the specified pattern or keyword.
By using grep, you can efficiently analyze log files and extract the information you need, making it a valuable tool for system administrators and developers.
To know more about grep
https://brainly.com/question/31256733?
#SPJ11
Provides a secure file-transfer service over a SSH connection and offers a file's original date and time information, which is not available with FTP (Wallace 52)
The file-transfer service being referred to in this question is SSH (Secure Shell), which provides a secure way to transfer files between two systems. Unlike FTP (File Transfer Protocol), SSH encrypts all data that is transferred between the systems, making it more secure. Additionally, SSH is able to provide the file's original date and time information, which is not available with FTP. This information can be important for maintaining accurate records and ensuring that files are properly tracked and managed.
Overall, using SSH for file transfer is a great way to ensure that your data is kept secure and that important information is not lost or altered during the transfer process.
To know more about file-transfer service
https://brainly.com/question/30514500?
#SPJ11
A tank is 20 years old and has a bottom thickness of 0.170". Original bottom thickness was 0.250". Determine the interval for the next internal inspection.
A) 10 years
B) 15 years
C) 17.5 years
D) 20 years
To determine the interval for the next internal inspection, we need to first calculate the corrosion rate and then use it to estimate when the tank will reach a critical thickness.
1. Calculate the thickness reduction:
Thickness reduction = Original thickness - Current thickness
Thickness reduction = 0.250" - 0.170" = 0.080"
2. Determine the corrosion rate:
Corrosion rate = Thickness reduction / Years in service
Corrosion rate = 0.080" / 20 years = 0.004" per year
3. Estimate the remaining life of the tank (assuming the critical thickness is 0.100"):
Remaining thickness = Current thickness - Critical thickness
Remaining thickness = 0.170" - 0.100" = 0.070"
4. Calculate the time until the tank reaches the critical thickness:
Time until critical thickness = Remaining thickness / Corrosion rate
Time until critical thickness = 0.070" / 0.004" per year = 17.5 years
Based on this calculation, the next internal inspection should be scheduled at half of the remaining life, which is 17.5 / 2 = 8.75 years. Since this option is not available in the given choices, the closest answer would be:
A) 10 years
To know about equipment inspection costs, visit :- https://brainly.com/question/28288755
#SPJ11
The maximum out-of-plumbness for a reconstructed tank shall not exceed:
A)1/30 of total tank height
B) 1/50 of the total tank height
C) 1/100 of the total tank height
D) 1/200 of the total tank height
Question: "The maximum out-of-plumbness for a reconstructed tank shall not exceed:"
Hi! The maximum out-of-plumbness for a reconstructed tank shall not exceed option B) 1/50 of the total tank height.
Learn more about out-of-plumbness: https://brainly.com/question/19971457
#SPJ11
What allows multiple communications sessions to share the same physical medium.
There are several techniques and protocols that allow multiple communications sessions to share the same physical medium. Some of these include.
Multiplexing: Multiplexing is the process of combining multiple data streams into a single stream that can be transmitted over a shared medium. There are various types of multiplexing techniques, such as time-division multiplexing (TDM), frequency-division multiplexing (FDM), and wavelength-division multiplexing (WDM). These techniques allow different communication sessions to be allocated different time slots, frequencies, or wavelengths, respectively, on the same physical medium. Packet-switching: In packet-switching networks, data is divided into smaller units called packets, which are then transmitted independently over the shared medium. Each packet contains information about its destination, allowing it to be routed to the appropriate recipient. This allows multiple communication sessions to share the same physical medium by interleaving packets from different sessions during transmission. Protocol-based sharing: Some communication protocols are designed to share the same physical medium efficiently. For example, Carrier Sense Multiple Access with Collision Detection (CSMA/CD) and Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) are protocols commonly used in Ethernet and Wi-Fi networks, respectively, that allow multiple communication sessions to share the same physical medium by detecting and avoiding collisions.
learn more about communication here:
https://brainly.com/question/22558440
#SPJ11
Who should be consulted if an opening on a CMU or brick wall is required? And why?
If an opening on a CMU or brick wall is required, it is best to consult with a licensed contractor or architect. This is because they have the knowledge and expertise to assess the structural integrity of the wall and determine the proper method for creating the opening without compromising the stability of the wall. They can also ensure that any necessary permits and building codes are followed.
Attempting to create an opening without consulting a professional can result in damage to the wall or even safety hazards.
To know more about CMU
https://brainly.com/question/31329644?
#SPJ11
Which CPU feature enables the microprocessor to support running multiple operating systems at the same time?
The CPU feature that enables a microprocessor to support running multiple operating systems simultaneously is called virtualization. Virtualization allows a single physical server to be divided into multiple virtual servers, each with their own operating system, which can run independently of each other.
This feature is made possible by using a hypervisor, a layer of software that manages the virtual machines and their resources, allowing each operating system to have its own virtual hardware environment.Virtualization provides numerous benefits, such as better resource utilization, increased flexibility, and reduced costs. It allows multiple operating systems to run on a single physical server, reducing the need for additional hardware and the associated costs. Additionally, virtualization allows for easier management of resources, as virtual machines can be moved between physical servers without requiring any changes to the underlying hardware.In conclusion, virtualization is the CPU feature that enables a microprocessor to support running multiple operating systems at the same time. It allows for better resource utilization, increased flexibility, and reduced costs, making it an essential technology for modern computing environments.For such more question on physical server
https://brainly.com/question/31037702
#SPJ11
Most crystalline solids are poly-crystalline, which means they are composed of many small crystals or "grains" that
are separated by "grain boundaries". True or false?
True. Most crystalline solids are indeed polycrystalline, meaning they are composed of many small crystals or grains that are separated by grain boundaries.
Grain boundaries are interfaces between adjacent grains in a polycrystalline material, and they can have different properties compared to the grains themselves due to their unique structure and composition. Grain boundaries can influence the mechanical, electrical, and chemical properties of crystalline materials, and they play a significant role in the overall behavior of polycrystalline materials.
learn more about crystalline here:
https://brainly.com/question/30343293
#SPJ11
8. What state must all burnable substances be reduced to burn in air?
When substances react spontaneously with oxygen giving off heat and light, the heat released fuels and makes the process further violent and rapid. It is at the gaseous state all burnable substances be reduced to burn in air.
The process in which a substance burns in the presence of oxygen to produce heat and light is defined as combustion. When the reaction occurs in the presence of abundant oxygen, the substance burns in oxygen to the maximum extent.
Combustion resulting in fire can only occur between gases. The fuels in liquid and solid states must be vaporised to be a flame.
To know more about Combustion, visit;
https://brainly.com/question/14335621
#SPJ4
What other items does the GCU operate during start
Answer:
The GCU (Generator Control Unit) is responsible for controlling and monitoring various systems during the start-up and operation of a generator. In addition to controlling the starter motor and the generator itself, the GCU may also operate other items such as fuel pumps, cooling fans, and other ancillary systems required for proper operation of the generator. The specific components and systems controlled by the GCU will vary depending on the design and configuration of the generator system.
