Answer:
[tex]K = \frac{h'}{8 m \ \Delta x^2}[/tex]K
Explanation:
The Heisenberg uncertainty principle is
Δx Δp ≥ h' / 2
h’ =[tex]\frac{h}{2\pi }[/tex]
The kinetic energy of a particle is
K = ½ m v²
p = mv
v = [tex]\frac{p}{m}[/tex]
substitute
K = [tex]\frac{1}{2} \frac{p^2}{m}[/tex]
from the uncertainty principle,
Δp = [tex]\frac{h'}{2 \ \Delta x}[/tex]
we substitute
K = [tex]\frac{1}{2m} ( \frac{h'}{2 \ \Delta x})^2[/tex]
[tex]K = \frac{h'}{8 m \ \Delta x^2}[/tex]
Assuming 84.0% efficiency for the conversion of electrical power by the motor, what current must the 13.0-V batteries of a 716 kg electric car be able to supply to climb a 3.00 x 102 m high hill in 2.00 min at a constant 22.0 m/s speed while exerting 7.00 x 102 N of force to overcome air resistance and friction
Answer:
[tex]\mathbf{ current(I) =1766.67 \ A}[/tex]
Explanation:
Given that:
The air resistance and friction = 700 N
The gravity caused force = 716 × 9.8 = 7016.8
Total force = (7016.8 + 700) N
Total force = 7716.8 N
∴
[tex]13 \times current(I) \times 0.84 = \dfrac{7716.8 \times 300}{2 \times 60}[/tex]
[tex]current(I) \times 10.92= 19292[/tex]
[tex]current(I) = \dfrac{19292}{10.92}[/tex]
[tex]\mathbf{ current(I) =1766.67 \ A}[/tex]
Which image represents a transverse mechanical wave?
Answer:
A
Explanation:
It is kinda like a spring.
The image which represents a transverse mechanical wave is A.
What is a mechanical wave?The wave has motion if all points on a wave vibrate at right angles to the direction of the wave propagation.
A transverse wave is a mechanical wave which is much like sinusoidal wave which has particles vibrating about their equilibrium position perpendicular to the direction of the motion of the wave.
Hence, the image which represents a transverse mechanical wave is A.
Learn more about mechanical wave.
https://brainly.com/question/3101711
#SPJ2
What are regular and irregular reflection of light? plz help its
urgent..
Explanation:
Regular reflection: It is the reflection from a smooth surface such that the light rays are evenly parallel to each other and an image is formed. ... Irregular reflection: It is the diffused reflection from uneven surface such that the light rays are not parallel to each other and do not form an image.
Q5. Use Superposition to V. in the circuit below? (5 points)
4 mA
12V
2 ΚΩ
2 mA
1 ΚΩ
2 ΚΩ
Answer:
4va
12va
2jk
1jk
2jk
1. Three centimeters of water evaporated from a 200-hectare vertical walled reservoir during 24 hours. Storm water was added to the reservoir at a constant rate of 3 m3/s during this period. Determine the volume in ha-cm of water released during the period (through the bottom of the reservoir) if the water level was the same at the beginning and the end of the day.
Answer:
25920 ha-cm
Explanation:
Since water evaporates from the reservoir at a rate of 3 cm in 24 hours, its height changes at a rate of 3 cm/24 × 3600 s = 3 cm/86400s = 3.472 10⁻⁵ cm/s.
Now, the volume loss is dV/dt = dV/dh × -dh/dt
= dV/dt × -3.472 × 10⁻⁵ cm/s
= -3.472 × 10⁻⁵ cm/sdV/dh
The reservoir increases in volume at a rate of 3 m³/s = 3 × 10⁶ cm³/s in 24 hours.
So, the net rate of volume change per unit time of the reservoir is
3 × 10⁶ cm³/s - 3.472 × 10⁻⁵ cm/sdV/dh = Adh/dt where A = area of vertical walled reservoir and dh/dt = change in height of the reservoir with respect to time
So, 3 × 10⁶ cm³/s - 3.472 × 10⁻⁵ cm/sdV/dh = Adh/dt
Since dh/dt = 0 in 24 hours(since the water level remains the same after 24 hours, that is dh = 0)
3 × 10⁶ cm³/s - 3.472 × 10⁻⁵ cm/sdV/dh = Adh/dt
3 × 10⁶ cm³/s - 3.472 × 10⁻⁵ cm/sdV/dh = A × 0
3 × 10⁶ cm³/s - 3.472 × 10⁻⁵ cm/sdV/dh = 0
3.472 × 10⁻⁵ cm/sdV/dh = 3 × 10⁶ cm³/s
dV/dh = 3 × 10⁶ cm³/s ÷ 3.472 × 10⁻⁵ cm/s
dV/dh = 8.64 × 10¹¹ cm²
dV = (8.64 × 10¹¹ cm²)dh
Integrating both sides with V from 0 to V and h from h = 0 to h = 3 cm, we have
∫dV = ∫(8.64 × 10¹¹ cm²)dh
∫dV = (8.64 × 10¹¹ cm²)∫dh
V = (8.64 × 10¹¹ cm²)[h]₀³
V = (8.64 × 10¹¹ cm²)[3 cm - 0 cm]
V = (8.64 × 10¹¹ cm²)(3 cm)
V = 25.92 × 10¹¹ cm³
V = 2.592 × 10¹² cm³
V = 2.592 × 10¹² cm² × 1 cm
Since 1 ha = 10⁸ cm²,
V = 2.592 × 10¹² cm² × 1 ha/10⁸ cm² × 1 cm
V = 2.592 × 10⁴ ha-cm
V = 25920 ha-cm
The electric field 30cm from a van de Graaff generator is measured to be 28,300N/C. What is the charge of the van de Graaf?
Answer:
14
Explanation:
EWAN KO LANG DIN BASTA YAN ALAM KO
The physics of wind instruments is based on the concept of standing waves. When the player blows into the mouthpiece, the column of air inside the instrument vibrates, and standing waves are produced. Although the acoustics of wind instruments is complicated, a simple description in terms of open and closed tubes can help in understanding the physical phenomena related to these instruments. For example, a flute can be described as an open-open pipe because a flutist covers the mouthpiece of the flute only partially. Meanwhile, a clarinet can be described as an open-closed pipe because the mouthpiece of the clarinet is almost completely closed by the reed.
Consider a pipe of length 80.0 cm open at both ends. What is the lowest frequency f of the sound wave produced when you blow into the pipe?
Answer:
Explanation:
Lowest frequency will be the fundamental frequency . For fundamental note
λ /2 = L where λ is wavelength of sound produced and L is length of open end pipe .
Given L = 80 cm
λ /2 = 80
λ = 160 cm .
= 1.6 m
frequency of note = velocity of sound / wavelength
= 330 / 1.6
= 206.25 Hz .
206 Hz approx.
Someone help please
Answer:
it would be downwards due to gravitational force
What is the weight of a 44.5 kg object?
Answer:
98.11 I think
Explanation:
I really hope this helps have a wonderful day
Plzzz answer this question correctly
Answer:
changing the direction in which a force is exerted
If 0.5 C charge passes through a wire in 10 seconds, what will be the value of the current flowing through the wire? *
20 mA
30 mA
50 mA
60 mA
Answer:
electric current passing through it will be 50mA
Explanation:
electric current = charge / time
I = Q / TI = 0.5 / 10 I = 0.05 amperecurrent = 0.05 A = 50mA
If 0.5C charge passes through a wire in 10 seconds, then 50mA current is flowing through the wire. Thus, the correct option is C.
What is Electric current?
Electric current is the flow of electricity in an electronic circuit. It is the amount of electricity flowing through a electronic circuit. It is generally measured in amperes (A). The larger the value in amperes, the more electricity is flowing in that circuit.
The formula for calculation of Electric current is:
I = Q/T
where, I = electric current,
Q = amount of charge,
T = time required
Therefore, the current flowing in the wire is:
I = 0.5C/ 10 seconds
I = 0.05 A or 50mA (1mA = 10⁻³A)
Therefore, the correct option is C.
Learn more about Electric current here:
https://brainly.com/question/2264542
#SPJ6
Tyler and Jim race each other up a mountain on their bicycles. Tyler rides a road bike on the switchbacks of the twisting and turning mountain road. Jim rides a mountain bike and follows a direct, but steeper, straight-line path up the mountain. They start at the same time and place at the bottom of the mountain and finish at the same time and place at the top of the mountain. From start to finish a. whose distance traveled was longer? b. whose displacement was longer? c. which rider had the faster average speed? d. which rider had the faster average velocity? e. who won the race?
Answer:
Explanation:
Displacement is minimum distance between initial and final point .
Distance is total length of path covered in a journey .
a )
Tyler covered a longer distance in the journey because total length of path covered by him is longer due to curved path .
b )
Both have same displacement , because minimum distance between initial and final point in both the case is same .
c )
average speed = distance / time
as time is same for both the case ,
average speed ∝ distance
As distance covered by Tyler is more , his average speed is more .
d )
average velocity = displacement / time
As both displacement and time are same in both the case , average velocity in both the case is same .
e )
They start at the same time and place at the bottom of the mountain and finish at the same time , both have tie and nobody won the race , in spite of speed of Tyler being greater .
A steel cylinder of length 10 cm, mass 160 g and density 8 g/em. The radius of the cylinder is
Answer:
0.8cm
Explanation:
Volume = mass/density = 160/8 = 20cm³
Volume = πr²h
r² = v/πh = 20/10π =0.64
r = √0.64 = 0.8
How long will it take an object traveling at 90 kilometers per hour to travel 910 kilometers?
Explanation:
time = distance / velocity
We know that distance = 910 km and velocity = 90 km/h.
t = d / v
t = 910 km / 90 km/h
t = 10.11 hrs
The object traveled for 10.11 hours long. Hope this helps, thank you !!
Plzzz help me with this
I’ll give brainliest
Answer:
(A) By reducing friction
Answer:
A
Explanation:
4. Kenny Kinematic notes that he is at mile marker 334 on the highway. He travels south to mile marker 181. What is his displacement?
Answer:
153miles
Explanation:
Distance on the highway = +334miles
Distance through south = -181miles (towards the negative direction)
Displacement will be the sum of the distances
Displacement = +334-181
Displacement = 153miles
Hence the displacement is 153miles
How much force is needed to accelerate a Kia Soul with a
mass of 1200 kg to 5 m/s2?
Answer:
[tex]\boxed {\boxed {\sf 6,000 \ Newtons}}[/tex]
Explanation:
Force is the product of mass and acceleration.
[tex]F=ma[/tex]
The mass of the Kia Soul is 1200 kilograms and its acceleration is 5 meters per square second.
[tex]m= 1200 \ kg \\a= 5 \ m/s^2[/tex]
Substitute the values into the formula.
[tex]F= 1200 \ kg * 5 \ m/s^2[/tex]
Multiply.
[tex]F= 6000 \ kg*m/s^2[/tex]
1 kilgram meter per square second is equal to 1 Newton. Our answer of 6000 kg*m/s² equals 6000 N[tex]F= 6000 \ N[/tex]
Answer:
Given :-Mass = 1200 kgAcceleration = 5 m/s²To Find :-Force
Solution :-We know that
F = ma
F = Force
m = mass
a = acceleration
F = 1200 × 5
F = 6000 N
[tex] \\ [/tex]
A vertical wire carries a current straight up in a region of the magnetic field directed north. What is the direction of the magnetic force on the current due to the magnetic field
Answer:
The direction of the force on the vertical wire is towards the East or right.
Explanation:
Using Fleming's right hand rule, the current is the middle finger pointing straight up, the magnetic field is the fore-finger pointing Northwards and then the thumb is the direction of the force on the vertical wire.
Following these conventions, the thumb points towards the East. So, the direction of the force on the vertical wire is towards the East or right.
A block of mass m = 150 kg rests against a spring with a spring constant of k = 880 N/m on an inclined plane which makes an angle of θ degrees with the horizontal. Assume the spring has been compressed a distance d from its neutral position.
Required:
a. Set your coordinates to have the x-axis along the surface of the plane, with up the plane as positive, and the y-axis normal to the plane, with out of the plane as positive.
b. Denoting the coefficient of static friction by μs, write an expression for the sum of the forces in the x-direction just before the block begins to slide up the inclined plane. Use defined quantities and g in your expression ΣFx = 25%
c. Assuming the plane is frictionless, what will the angle of the plane be, in degrees, if the spring is compressed by gravity a distance 0.1 m?
d. Assuming θ = 45 degrees and the surface is frictionless, how far will the spring be compressed, d in meters?
Answer:
b) k Δx - W cos θ - μ mg cos θ = m a , c) θ = 86.6º, d) Δx = 1.18 m
Explanation:
a) In the attachment we can see a diagram of the forces in this problem and the coordinate axes for its decomposition.
F is the force applied by the spring, while it is compressed, this force disappears when the block leaves the spring
b) Let's apply Newton's second law for when the spring is compressed
let's use trigonometry to break down the weight
sin θ = Wₓ / W
cos θ = W_y / W
Wₓ = W sin θ
W_y = W cos θ
Y axis
N - W_y = 0
N = W_y
N = W cos θ
X axis
F -Wₓ -fr = ma
the force applied by the spring is given by hooke's law
F = k Δx
friction force has the expression
fr = μ N
fr = μ W cos θ
we substitute
k Δx - W cos θ - μ mg cos θ = m a ( 1)
c) If the plane has no friction, what is the angle so that Δx = 0.1m
We write the equation 1, with fr = 0 and since the system is still a = 0
k Δx - W cos θ -0 = 0
cos θ = [tex]\frac{k \Delta x}{ m g}[/tex]
cos θ = [tex]\frac{880 \ 0.1}{ 150 \ 9.8}[/tex]
cos θ = 0.0598
θ = cos⁻¹ 0.0598
θ = 86.6º
d) In this part they give the angle θ = 45º and there is no friction, they ask the compression
the acceleration is zero, we substitute in 1
k Δx - W cos θ - 0 = 0
Δx = [tex]\frac{mg \ cos \ \theta}{k}[/tex]
Δx = [tex]\frac{ 150 \ 9.8 \ cos45}{880}[/tex]
Δx = 1.18 m
Galileo _____.
did not believe friction existed
believed that friction stopped objects in motion
believed that friction kept objects in motion
assumed that in a frictionless environment objects would never move
Answer:
friction help to slow motion in other word it oppose motion, but in a frictionless environment object would move with difficult stopping point.
A football quarterback runs 15.0 m straight down the playing field in 2.30 s. He is then hit and pushed 3.00 m straight backward in 1.74 s. He breaks the tackle and runs straight forward another 28.0 m in 5.20 s.
Calculate his average velocity (in m/s) for each of the three intervals. (Assume the quarterback's initial direction is positive. Indicate the direction with the sign of your answer.)
Answer:
6.52 m/s
1.72 m/s
5.38 m/s
Explanation:
this question requires us to find the average velocity.
1. velocity in straight down direction:
velocity = distance/time
= 15.0/2.30
= 6.52 m/s
2. velocity in straight backward direction:
velocity = distance/time
= 3.00 /1.74
= 1.72m/s
3. velocity in straight forward direction
velocity = distance/time
= 28.0/5.20
= 5.38 m/s
these are the his velocities for each if the intervals.
thank you!
Which of the following choices is the best example of potential energy?
Answer:
A basketball sitting still in a players hands
Explanation:
The other 3 answers have the ball in motion (going towards the basket, bouncing, and rolling) so that would be kinetic energy.
When the basketball is sitting in the player's hands, it has the potential to be in motion.
Answer:
it is D not B it D
Explanation:
what is the relationship between net impulse and change in momentum?
Answer:
impulse equals the average net external force multiplied by the time this force acts. It is equal to the change in momentum.
Explanation:
1. Clara stops for 10 minutes to catch up with a friend.
Answer:
Clara has speed of 80m/min
Explanation:
Clara was jogging at 600 m in 5 minutes. She stopped suddenly which reduced her velocity and then she waited for 10 minutes so that her friends comes near her. She stopped to catch her friend. During this 10 minutes the velocity of Clara is zero. She started to walk again at a slower speed of 80m/min.
For PN junctions, determine if each statement below is True or False:
a. There can be large net current from p-side to n-side under forward bias.
b. There can be large net current from n-side to p-side under reverse bias if reverse bias is sufficiently high.
c. Electron diffusion current flows from n-side to p-side.
d. Electric field magnitude is higher under reverse bias
e. Electrons in the transition region drift from p-side to n-side.
Answer:
a) True
b) True
c) false
d) True
e) True
Explanation:
a) True
In forward bias, the resistance of the p–n junction reduces and hence the electric charges can flow easily.
b) True
In reverse bias condition, the electric current is due to the minority charge carriers (negative).
c) False
direction of diffusion current is in the direction of movement of positive charge i,e towards n side
d) True
Because the breakdown of charge carriers occur due to which the current increases rapidly
e) True
Find the GCF of each set of numbers.
12, 21, 30
Math
Answer:
3 is the GCF for all these numbers if thats what you're asking
Drag the tiles to the correct boxes to complete the pairs
Match the particles with their characteristics.
subatomic particles with a positive charge
subatomic particles with a negative charge
subatomic particles with no charge
made of atoms
neutrons
electrons
protons
malaria
Answer:
1. Protons.
2. Electrons.
3. Neutrons.
4. Molecules.
Explanation:
1. Protons: subatomic particles with a positive charge. They are bound together in the nucleus of an atom due to strong nuclear forces.
2. Electrons: subatomic particles with a negative charge. Electrons can be defined as subatomic particles that are negatively charged and as such has a magnitude of -1.
3. Neutrons: subatomic particles with no charge. The negative charge of the electrons cancels the positive charge of the protons.
4. Molecules: they are made of atoms.
Generally, molecules attach on the inside of a mineral to give it shape. Therefore, the molecule of a mineral is a crystal three-dimensional regular structure (arrangement) of chemical particles that are bonded together and determines its shape.
Due to the fact that these molecules are structurally arranged or ordered and are repeated by different symmetrical and translational operations they determine the shape of minerals.
Velocity time graph and how to draw it
Answer:
Velocity time graph
Explanation:
Draw on graph paper two straight lines originating at the same point and perpendicular to each other. This is the x-y axis. The x-axis is the horizontal line and the y-axis is the vertical line.
Mark appropriate equally-spaced time intervals on the x-axis so that you can easily graph the time values from the table.
Mark appropriate velocity increments on the y-axis so that you can easily graph the velocity values from the table. If you have negative velocity values, extend the y-axis downward.
Find the first time value from the table and locate it on the x-axis. Look at the corresponding velocity value and find it on the y-axis.
Put a dot where a straight line vertically drawn up through the x-axis value and a straight line horizontally drawn through the y-axis value intersect.
Plot in similar fashion for all other velocity-time pairs in your table.
Draw a straight line with a pencil, connecting each dot you have put down on the graph paper, going from left to right
Tell types of mirros and
each
one
Answer: We can identify the different types of mirrors without touching them by looking at the image it produces. Look into each mirror, the nature of the image produced will tell you the type of mirror it is.
- A plane mirror will produce an image of the same size as your face.
- A concave mirror will produce a magnified image of your face.
- A convex mirror will produce a diminished image of your face.
MARK ME BRAINLIST
Potential energy is energy due to the:
a. motion of an object.
b. height of an object.
c. temperature of an object.
d. speed of an object.
Answer:I will say d
Explanation: because Potential energy is the energy stored within an object, due to the object's position, arrangement or state. Potential energy is one of the two main forms of energy, along with kinetic energy.
