Alanine is also a non-polar amino acid and would have similar Protein structure of leucine. Thus, enzyme activity should be maintained because the polar basic should not undergo major change.
Alanine is an amino acid this is used to make proteins. It is used to interrupt down tryptophan and nutrition B-6. It is a supply of power for muscular tissues and the principal frightened gadget. It strengthens the immune gadget and allows the frame use sugars. Alanine is a nonacidic α-amino acid. Its aspect chain (a methyl group) is neither acidic (it isn't greater acidic than water) nor basic (it does now no longer have a nitrogen atom lone pair that isn't delocalized via way of means of resonance).
To learn more about amino acid check the link below-
https://brainly.com/question/14351754
#SPJ4
If we began the experiemtn with 0.70 g of cucl2 x 2 h2o, according to the stoichiometry o the reaction, how much al should be used to complete the reaction withtout either reactant being in excess
0.70 g of CuCl₂ • 2 H₂O reacts completely with 0.48 g of Al. The molar ratio of CuCl₂ • 2 H₂O to Al is 1:2. The reaction completes without any excess reactant.
The balanced chemical equation for the reaction between CuCl₂ • 2 H2O and Al is:
3CuCl₂ • 2 H₂O + 2Al → 3Cu + 2AlCl₃ + 6H₂O
From the equation, we can see that 3 moles of CuCl₂ • 2 H₂O react with 2 moles of Al. We need to find the amount of Al required to react completely with 0.70 g of CuCl₂ • 2 H₂O.
1 mole of CuCl₂ • 2 H₂O has a mass of (63.55 + 2 x 35.45 + 2 x 18.02) g = 170.48 g
0.70 g of CuCl₂ • 2 H₂O is equal to 0.70/170.48 = 0.0041 moles of CuCl₂ • 2 H₂O
From the balanced equation, we can see that 3 moles of CuCl₂ • 2 H₂O react with 2 moles of Al.
Therefore, the moles of Al required is (2/3) x 0.0041 = 0.0027 moles.
The molar mass of Al is 26.98 g/mol. Therefore, the mass of Al required is:
0.0027 moles x 26.98 g/mol = 0.073 g
Therefore, 0.073 g of Al should be used to complete the reaction without either reactant being in excess.
To know more about the molar ratio refer here :
https://brainly.com/question/17920577#
#SPJ11
Complete question :
If we began the experiment with 0.70 g of CuCl₂ • 2 H₂O, according to the stoichiometry of the reaction, how much Al should be used to complete the reaction without either reactant being in excess? Show your calculations.
A gas sample occupies a volume of 155 mL at a temperature of 316 K and a pressure of 0. 989 atm. How many moles of gas are there?
2Points
Show your work
There are approximately 0.00614 moles of gas in the sample.
To find the number of moles of gas in the sample, we will use the Ideal Gas Law formula: PV = nRT.
Given:
Volume (V) = 155 mL = 0.155 L (converted to liters)
Temperature (T) = 316 K
Pressure (P) = 0.989 atm
Gas constant (R) = 0.0821 L atm / K mol
We need to find the number of moles (n).
Rearranging the formula for n: n = PV / RT
1. Convert the volume to liters: 155 mL = 0.155 L
2. Plug in the given values into the formula: n = (0.989 atm) x (0.155 L) / (0.0821 L atm / K mol) x (316 K)
3. Simplify the equation and solve for n: n ≈ 0.00614 mol
To know more about Ideal Gas Law click on below link:
https://brainly.com/question/28257995#
#SPJ11
Question 1 options: calculate the energy, in joules, of a photon that has a frequency of 3.73 x 1014 s-1.
The energy of a photon can be calculated using the equation E = hf, where E is the energy of the photon, h is Planck's constant, and f is the frequency of the photon.
Substituting the given values, we get:
E = (6.626 x 10⁻³⁴ J s) x (3.73 x 10¹⁴ s⁻¹)
E = 2.47 x 10⁻¹⁹ J
Therefore, the energy of the photon with a frequency of 3.73 x 10¹⁴ s¹ is 2.47 x 10⁻¹⁹ J.
This value may seem small, but it is consistent with the fact that photons with higher frequencies (and thus higher energies) are required to cause certain types of chemical reactions and ionization processes.
The energy of a photon with a frequency of 3.73 x 1010¹⁴ s¹ is calculated using the equation E = hf, where h is Planck's constant. The energy of the photon is found to be 2.47 x 1010⁻¹⁹ J.
To know more about the energy of a photon refer here :
https://brainly.com/question/2393994#
#SPJ11
20. 0 g of Potassium reacts with water to produce Potassium hydroxide and hydrogen gas.
2 K + 2 H2O —> 2 KOH + H2
How many miles of hydrogen are there?
When 20.0 g of Potassium reacts with water, 0.256 moles of hydrogen gas are produced.
To determine the moles of hydrogen produced when 20.0 g of potassium reacts with water to form potassium hydroxide and hydrogen gas, follow these steps:
1. Determine the molar mass of potassium (K): The atomic weight of potassium is 39.1 g/mol.
2. Calculate the moles of potassium (K) used: moles = mass / molar mass
moles of K = 20.0 g / 39.1 g/mol ≈ 0.512 moles
3. Use the stoichiometry of the balanced equation to find the moles of hydrogen (H₂) produced: 2 moles K produce 1-mole H₂, so the ratio is 1:0.5.
4. Calculate the moles of H₂ produced: moles of H2 = moles of K * (1 mole H₂ / 2 moles K)
moles of H₂ = 0.512 moles * (1/2) ≈ 0.256 moles
So, when 20.0 g of potassium reacts with water to produce potassium hydroxide and hydrogen gas, there are approximately 0.256 moles of hydrogen.
Learn more about moles at https://brainly.com/question/29367909
#SPJ11
A 2. 50g sample of zinc is heated, then placed in a calorimeter containing 60. 0g of water. The temperature of water increases from 20. 00 degrees C. The specific heat of Zinc is 0. 390J/g Degree C. What was the initial temperature of the zinc metal sample?
We can use the equation:
q(zinc) = -q(water)
where q(zinc) is the heat lost by the zinc and q(water) is the heat gained by the water.
q(zinc) = m(zinc) × C(zinc) × ΔT
where m(zinc) is the mass of zinc, C(zinc) is the specific heat of zinc, and ΔT is the temperature change of the zinc.
The heat gained by the water :
q(water) = m(water) × C(water) × ΔT
where m(water) is the mass of water, C(water) is the specific heat of water, and ΔT is the temperature change of the water.
Since the calorimeter is assumed to be perfectly insulated, we can assume that the heat lost by the zinc is equal to the heat gained by the water:
m(zinc) × C(zinc) × ΔT = m(water) × C(water) × ΔT
m(zinc) × C(zinc) = m(water) × C(water)
2.50 g × 0.390 J/g°C = 60.0 g × 4.184 J/g°C
ΔT = q(water) / (m(water) × C(water))
= (2.50 g × 0.390 J/g°C) / (60.0 g × 4.184 J/g°C)
= 0.00916°C
Since we know the initial temperature of the water is 20.00°C, we can use the formula for temperature change:
ΔT = final temperature - initial temperature
Rearranging this formula, we get:
initial temperature = final temperature - ΔT
Substituting the given values, we get:
initial temperature = 20.00°C - 0.00916°C
= 19.99084°C
Therefore, the initial temperature of the zinc metal sample was approximately 19.99°C.
To know more about temperature change refer here:
https://brainly.com/question/28884653
#SPJ11
To determine experimentally if a reaction is exthermic a student should use a
To determine experimentally if a reaction is exothermic, a student should use a calorimeter. A calorimeter is a device used to measure the heat exchange during a chemical reaction, enabling the student to identify if the reaction is exothermic or endothermic. In an exothermic reaction, heat is released, causing the temperature of the surroundings to increase.
To perform the experiment, follow these steps:
1. Choose the appropriate chemical reaction to test.
2. Prepare the calorimeter by placing a known amount of water in the calorimeter's inner container.
3. Measure and record the initial temperature of the water.
4. Add the reactants (in their appropriate amounts) to the water, and quickly seal the calorimeter to minimize heat loss to the surroundings.
5. Stir the mixture gently to ensure proper mixing and heat distribution.
6. Monitor the temperature change of the water over time, recording the highest temperature reached.
7. Calculate the amount of heat released or absorbed by the reaction using the formula: q = mcΔT, where q is heat, m is the mass of water, c is the specific heat capacity of water, and ΔT is the change in temperature.
8. If the heat calculated is positive and the temperature increased, the reaction is exothermic; if negative and the temperature decreased, the reaction is endothermic.
In conclusion, a student should use a calorimeter to experimentally determine if a reaction is exothermic, as it allows for the accurate measurement of heat exchange and can indicate whether heat is released or absorbed during the reaction.
To know more about exothermic refer here
https://brainly.com/question/31214950#
#SPJ11
A sample of iron with a mass of 250.0 grams underwent a change in thermal energy of 5250
joules. Determine the change in temperature of the iron that occurred during this process.
If you have 500 ml of a 0.10 m solution of the acid, what mass of the corresponding sodium salt of the conjugate base do you need to make the buffer with a ph of 2.08 (assuming no change in volume)
The mass of the corresponding sodium salt of the conjugate base needed to make a buffer with a pH of 2.08.
To determine the mass of the corresponding sodium salt of the conjugate base needed to make a buffer with a pH of 2.08, you can follow these steps:
1. Identify the given information:
- Initial volume of acid solution: 500 mL
- Initial concentration of acid solution: 0.10 M
- Desired pH: 2.08
2. Use the Henderson-Hasselbalch equation:
pH = pKa + log ([conjugate base]/[acid])
3. Assuming the acid is a weak monoprotic acid (HA) and its conjugate base is A-, determine the pKa:
pKa = pH - log ([A-]/[HA])
4. Calculate the ratio of [A-] to [HA]:
[A-]/[HA] = 10^(pH-pKa)
5. Calculate the moles of HA in the 500 mL of 0.10 M solution:
moles of HA = (volume x concentration) = 500 mL x 0.10 mol/L = 0.050 mol
6. Calculate the moles of A- needed:
moles of A- = moles of HA x ([A-]/[HA]) ratio
7. Determine the molar mass of the sodium salt of the conjugate base (A-) using the molecular formula.
8. Calculate the mass of the sodium salt of the conjugate base:
mass = moles of A- x molar mass of A-
By following these steps, you will be able to determine the mass of the corresponding sodium salt of the conjugate base needed to make a buffer with a pH of 2.08.
To know more about conjugate base refer here: https://brainly.com/question/30086613#
#SPJ11
Drag and drop the words that accurately complete the chart below. Example a lion and a cheetah mistletoe on a tree a coyote eating a rabbit a remora and a shark clownfish and anemone parasitism friendship competition Type of Symbiosis mutualism 1:10 predation relationship commensalism collaboration alliance
Answer:
Lion and cheetah - Competition
Mistletoe on a tree - Parasitism
Coyote eating rabbit- Predatation
Remora and Shark - Mutualism
Clownfish and Anemone - Relationship
Explanation:
A solution is 0.010 m in ba2+ and 0.020 m in ca2+
required:
a. if sodium sulfate is used to selectively precipitate one of the cations while leaving the other cation in solution, which cation will precipitate first? what minimum concentration of na2so4 will trigger the precipitation of the cation that precipitates first?
b. what is the remaining concentration of the cation that precipitates first, when the other cation begins to precipitate?
a. In a solution that is 0.010 M in Ba²⁺ and 0.020 M in Ca²⁺, when sodium sulfate (Na₂SO₄) is used to selectively precipitate one of the cations, the cation that will precipitate first is Ba²⁺. The minimum concentration of Na₂SO₄ that trigger the precipitation of the cation that precipitates first is 5.5 x 10^-9 M Na₂SO₄.
b. The remaining concentration of the cation that precipitates first, when the other cation begins to precipitate is 2.0 x 10^-2 M.
Let us discuss this in detail.
a. To determine which cation will precipitate first, we need to compare the solubility product constants (Ksp) of their respective sulfates. The Ksp for BaSO₄ is 1.1 x 10^-10 and the Ksp for CaSO₄ is 2.4 x 10^-5. Since the Ksp for CaSO₄ is much larger, it means that CaSO₄ is more soluble than BaSO₄. Therefore, Ba²⁺ will precipitate first.
To calculate the minimum concentration of Na₂SO₄ needed to trigger the precipitation of Ba²⁺, we need to use the common ion effect. This means that we need to add enough sulfate ions to the solution to exceed the solubility product constant of BaSO₄. The equation for the dissociation of Na₂SO₄ is:
Na₂SO₄(s) → 2 Na⁺(aq) + SO₄²⁻(aq)
Since we have 0.010 M Ba²⁺ in the solution, we need to add enough SO₄²⁻ ions to exceed the Ksp of BaSO₄. This can be calculated using the equation:
Ksp = [Ba²⁺][SO₄²⁻]
1.1 x 10^-10 = (0.010 M)(x)
x = 1.1 x 10^-8 M
This means that we need to add at least 1.1 x 10^-8 M SO₄²⁻ ions to trigger the precipitation of Ba²⁺. Since Na₂SO₄ dissociates to give 2 SO₄²⁻ ions for every formula unit, we need to add:
(1.1 x 10^-8 M) / 2 = 5.5 x 10^-9 M Na₂SO₄
b. Once Ba²⁺ starts to precipitate, the concentration of Ba²⁺ ions in the solution will decrease until it reaches a new equilibrium. At this point, the concentration of Ca²⁺ will still be 0.020 M. To calculate the new concentration of Ba²⁺ at this equilibrium, we need to use the equation:
Ksp = [Ba²⁺][SO₄²⁻]
1.1 x 10^-10 = (x)(5.5 x 10^-9 M)
x = 2.0 x 10^-2 M
Therefore, the remaining concentration of Ba²⁺ at equilibrium will be 2.0 x 10^-2 M.
Learn more about cations at https://brainly.com/question/14309645
#SPJ11
If the balloon was filled up to a volume of 2. 0 L at room temperature (25oC), what will the new volume be if the balloon is placed in the freezer for a few hours at -20oC?Gay-Lussac’s Law.
The new volume, by using Gay-Lussac's Law, of the balloon after being placed in the freezer would be 1.3 L.
Gay-Lussac’s Law, also known as the pressure-temperature law, states that the pressure and temperature of a gas are directly proportional to each other, provided that the volume and the amount of gas remain constant.
This law is represented mathematically as P1/T1 = P2/T2, where P1 and T1 represent the initial pressure and temperature, and P2 and T2 represent the final pressure and temperature.
In this case, we can use Gay-Lussac’s Law to determine the new volume of the balloon after being placed in the freezer. Since the amount of gas and the volume remain constant, we can rearrange the equation to solve for the new volume.
First, we need to convert the temperatures to Kelvin (K) since the equation requires absolute temperature. To do this, we add 273.15 to the given temperatures. Therefore, the initial temperature (25oC) is 298.15 K, and the final temperature (-20oC) is 253.15 K.
Using the equation P1/T1 = P2/T2, we can solve for the new pressure at the final temperature:
P2 = P1(T2/T1) = (1 atm)(253.15 K/298.15 K) = 0.85 atm
Now that we have the final pressure, we can use the ideal gas law to determine the new volume:
PV = nRT
V2 = (nRT2)/P2
Assuming that the amount of gas and the gas constant (R) remain constant, we can simplify the equation to:
V2/V1 = T2/T1(P2/P1)
Plugging in the given values, we get:
V2/2.0 L = (253.15 K)/(298.15 K)(0.85 atm)/(1 atm)
Simplifying this equation, we get:
V2 = 1.3 L
Therefore, the new volume of the balloon after being placed in the freezer would be 1.3 L.
To know more about Gay-Lussac's Law, visit:
https://brainly.com/question/1358307#
#SPJ11
Find the mass of a sample of water if its temperature dropped 24. 8°C
when it lost 870 J of heat. Hint. Which formula are you going to use? See
interactive PPT. Don't forget the unit. Show your work.
How much heat is required to warm a 135g cup of water from 15 °C to
35°C? Hint: the water is in a cup so what state of matter and specific heat?
Show your work.
1. The mass of the water sample is approximately 8.77 grams.
2. Approximately 11,322 Joules of heat are required to warm a 135g cup of water from 15°C to 35°C.
We're given the values:
Q = -870 J (lost heat, so negative value)
ΔT = -24.8°C (temperature dropped)
c = 4.18 J/(g°C) (specific heat capacity of water)
Rearrange the formula to solve for mass:
m = Q / (cΔT)
Plug in the values:
m = -870 / (4.18 × -24.8)
m ≈ 8.77 g
The mass of the water sample is 8.77 grams.
We're given the values:
m = 135 g
ΔT = 35°C - 15°C = 20°C
c = 4.18 J/(g°C) (specific heat capacity of water)
Now, use the formula Q = mcΔT to find the heat required:
Q = 135 × 4.18 × 20
Q ≈ 11322 J
Approximately 11,322 Joules of heat are required to warm a 135g cup of water from 15°C to 35°C.
To know more about specific heat capacity click on below link:
https://brainly.com/question/29766819#
#SPJ11
Part D
Press the yellow reset button at the bottom of the simulation screen. Under Constant Parameter, select Volume. Again,
pump the pump handle once to introduce 40 to 50 gas molecules. Record the pressure in the data table.
Use the heat control to heat the gas to each of the other temperatures in the data table, and record the new pressure.
Answer from Edmentum :)
The instruction is to use the PhET simulation to perform an experiment where the constant parameter is set to volume, and then to pump 40 to 50 gas molecules into the simulation.
The pressure of the gas is recorded in a data table. Next, the heat control is used to heat the gas to each of the other temperatures in the data table, and the corresponding new pressure values are recorded in the data table. This experiment demonstrates the relationship between pressure and temperature, which is known as the ideal gas law.
By holding the volume constant and changing the temperature, we can observe how the pressure of the gas changes. This experiment is useful in understanding real-world phenomena such as how temperature affects the pressure of gas inside a container, such as a tire or a balloon.
To know more about the Pressure, here
https://brainly.com/question/15813117
#SPJ4
What volume of 0. 125 m kmno4 is required to yield 0. 180 mol of potassium permanganate, kmno4?.
1.44 liters of 0.125 M [tex]KMnO4[/tex] solution is required to yield 0.180 mol of [tex]KMnO4[/tex].
To determine the volume of 0.125 M [tex]KMnO4[/tex] solution required to yield 0.180 mol of [tex]KMnO4[/tex], we can use the following formula:
moles = concentration x volume
We can rearrange this formula to solve for volume:
volume = moles / concentration
First, we can calculate the volume of 0.125 M [tex]KMnO4[/tex] solution that contains 0.180 moles of [tex]KMnO4[/tex]:
volume = moles / concentration
volume = 0.180 mol / 0.125 mol/L
volume = 1.44 L
Therefore, 1.44 liters of 0.125 M [tex]KMnO4[/tex] solution is required to yield 0.180 mol of [tex]KMnO4[/tex].
To know more about yield refer to-
https://brainly.com/question/30700754
#SPJ11
If you started with 20. 0 g of a radioisotope and waited for 3 half-lives to pass, then how much would remain? 1. 25g
5. 00g
10. 0g
2. 50g
Answer: The answer is 2.50g.
I hope this helps and have a great day!
If 450.5 calories of heat energy are added to a 89.6 gram sample of aluminium (specific heat of 0.215 calories per gram degree celsius) and the initial temperature of the sample is 25.7 degrees celsius then what is the final temperature in degrees celsius?
The final temperature is 49.2 degrees Celsius.
To find the final temperature, we can use the formula:
Q = mcΔT
where Q represents the amount of heat energy measured in calories (450.5 calories), m represents the mass of the substance in grams (89.6 grams), c represents the specific heat capacity in calories per gram per degree Celsius (0.215 calories/gram degree Celsius), and ΔT represents the change in temperature.
First, we need to find the change in temperature (ΔT):
450.5 calories = (89.6 grams) * (0.215 calories/gram degree Celsius) * ΔT
Now, we can solve for ΔT:
ΔT = 450.5 calories / [(89.6 grams) * (0.215 calories/gram degree Celsius)] ≈ 23.5 degrees Celsius
Since we know the initial temperature (25.7 degrees Celsius), we can find the final temperature:
Final temperature = Initial temperature + ΔT = 25.7 degrees Celsius + 23.5 degrees Celsius ≈ 49.2 degrees Celsius
Know more about Heat Energy here:
https://brainly.com/question/25384702
#SPJ11
Benzene at 20°C has a viscosity of 0. 000651 Pa. S. What shear stress is required to deform this fluid at a velocity gradient of 4900 s-1 ?
To calculate the shear stress required to deform benzene at a velocity gradient of 4900 s-1, we can use the equation:
Shear stress = viscosity x velocity gradient
Plugging in the given values, we get:
Shear stress = 0.000651 Pa. S x 4900 s-1
Shear stress = 3.19 Pa
Therefore, a shear stress of 3.19 Pa is required to deform benzene at a velocity gradient of 4900 s-1.
What is Shear stress?
Shear stress is a type of stress that occurs when a force is applied parallel to a surface or along a plane within a material. It is the result of the force causing the material to deform or change shape, with one part of the material sliding or shearing over another part.
Shear stress is often described in terms of the shear force per unit area, or shear strength, that is required to cause the material to shear or deform. The unit of measurement for shear stress is typically in pascals (Pa) or pounds per square inch (psi).
To know more about Shear stress:
https://brainly.com/question/12910262
#SPJ11
Any atom that has 13 protons is an aluminum atom. Which statement best describes what would happen if a proton were added to an aluminum atom?.
If a proton were added to an aluminum atom, it would result in the formation of a new atom with 14 protons, which is a Silicon atom.
The addition of a proton would increase the atomic number of the aluminum atom by one, changing it to 14, which is the atomic number of silicon. This would result in a change in the electronic configuration of the atom, leading to different chemical properties. The new atom would have one more electron than the original aluminum atom, which would occupy a new orbital. This would result in a change in the valence shell electronic configuration and reactivity of the atom.
To know more about Silicon atoms, here
brainly.com/question/13568870
#SPJ1
1. Albertans experience extreme temperature ranges from summer months to winter months.
The air pressure inside a car tire in summer at 25.0 °C is 310 kPa. If the volume remains
fixed, what is the pressure in the winter at -30.0 °C?
Assuming ideal gas behavior, the pressure in the winter at -30.0 °C would be approximately 166.3 kPa.
The pressure of a gas is directly proportional to its temperature, according to the ideal gas law.
Therefore, if the temperature of the gas inside a car tire changes, the pressure will change as well, assuming the volume remains constant.
To solve this problem, we can use the combined gas law, which relates the pressure, temperature, and volume of a gas. The formula is:
[tex]P1/T1 = P2/T2[/tex]
where P1 and T1 are the initial pressure and temperature, respectively, and P2 and T2 are the final pressure and temperature.
Using this formula, we can solve for the final pressure as follows:
[tex]P2 = (P1*T2)/T1[/tex]
Plugging in the values given in the problem, we get:
[tex]P2 = (310 kPa * (-30.0 + 273.15) K) / (25.0 + 273.15) K[/tex]
P2 = 166.3 kPa
Therefore, the pressure inside the car tire in winter at -30.0 °C is 166.3 kPa. This represents a decrease in pressure compared to the summer pressure of 310 kPa.
It is important to note that the ideal gas law assumes that the volume remains constant, which may not be the case in real-world situations where the volume of a tire can change due to various factors such as wear and tear.
For more such questions on pressure, click on:
https://brainly.com/question/24719118
#SPJ11
write the net ionic equation for the equilibrium that is established when sodium cyanide is dissolved in water. This solutions is: (acid, base, neutral)
The net ionic equation for the equilibrium that is established when sodium cyanide (NaCN) is dissolved in water is:
NaCN + H2O ⇌ CN- + Na+ + H2O
In this equation, the cyanide ion (CN-) is produced by the dissociation of NaCN in water. The sodium ion (Na+) and water (H2O) are spectator ions and do not participate in the reaction. Therefore, they are not included in the net ionic equation.
This solution is basic because the cyanide ion is a weak base and can hydrolyze water to produce hydroxide ions (OH-) according to the following reaction:
CN- + H2O ⇌ HCN + OH-
The equilibrium constant for this reaction is relatively small, but it is enough to make the solution basic.
Visit here to learn more about ionic equation brainly.com/question/29299745
#SPJ11
A decomposition of hydrogen peroxide into water and oxygen gas is an exothermic reaction. If the temperature is initially 28˚ C, what would you expect to see happen to the final temperature? Explain what is happening in terms of energy of the system and the surroundings.
If the decomposition of hydrogen peroxide into water and oxygen gas is an exothermic reaction, we would expect the final temperature to be lower than the initial temperature of 28˚C.
This is due to the fact that energy is released from the system during an exothermic reaction in the form of heat into the surroundings. In other words, the energy of the reactants is more than that of the products, and the excess energy is released into the environment.
As a result, the environment's temperature will rise, while the system's temperature will fall. This indicates that the reaction's final temperature will be lower than its 28° C starting point.
To learn more about an exothermic reaction, follow the link:
https://brainly.com/question/10373907
#SPJ1
Three students are asked to discuss whether Gibbs Free Energy was positive or
negative for each dissolution. Select the student that employs correct
scientific reasoning.
. Student 1: The Gibbs Free Energy was negative for both reactions because the reactions were
spontaneous, the reactions happened.
• Student 2: The Gibbs Free Energy was positive for the first reaction because it got colder and
negative for the second reaction because it got hotter.
• Student 3: The Gibbs Free Energy was positive for both reactions because it is always positive for
dissolutions.
Student 3
Student 2
Student 1
In the next three problems, use the CER format to answer this guiding
Based on scientific reasoning, the correct student is Student 1.
The Gibbs Free Energy is negative for both reactions because they are spontaneous, meaning they occur naturally without the need for external input. This indicates that the reactions release energy and are thermodynamically favorable.
Student 2's reasoning is incorrect because the temperature change alone does not determine the Gibbs Free Energy.
Student 3's reasoning is also incorrect because the Gibbs Free Energy can be both positive and negative depending on the reaction conditions. Therefore, Student 1's explanation aligns with the laws of thermodynamics and is scientifically accurate.
To know more about Gibbs Free Energy click on below link:
https://brainly.com/question/13318988#
#SPJ11
Determine the number of moles present in each compound. 6.50 g ZnSO4.
The number of moles present in 6.50g of ZnSO4 is 0.0403 moles.
How to calculate no of moles?The number of moles in a substance can be calculated by dividing the mass of the substance by its molar mass as follows:
no of moles = mass ÷ molar mass
According to this question, 6.50 grams of zinc sulphate is given. The number of moles in the substance can be calculated as follows:
molar mass of zinc sulphate = 161.47 g/mol
no of moles = 6.50g ÷ 161.47 g/mol
no of moles = 0.0403 moles
Learn more about moles at: https://brainly.com/question/20928252
#SPJ1
Calcium Carbonate reacts with HCl to produce Calcium chloride, carbon dioxide and water.(I) calculate the number of moles of CO2 produced from 36.5g of HCl (ii) Calculate the amount of Calcium chloride produced (in g) when 3 moles of calcium Carbonate reacts with HCl
Answer:
i. 0.50 mol CO2
ii. 332.94g CaCl2
Explanation:
CaCO3 + 2HCl -> CaCl2 + CO2 + H2O
i. 36.5g HCl * 1 mol HCl/36.46g HCl * 1 mol CO2/2 mol HCl = 0.50 mol CO2
ii. 3 mol CaCO3 * 1 mol CaCl2/1 mol CaCO3 * 110.98g CaCl2/1 mol CaCl2 = 332.94g CaCl2
How can you determine the specific heat capacity of 1. 0g of yam
Specific heat capacity is the amount of heat required to raise the temperature of a substance by one degree Celsius per unit of mass.
To determine the specific heat capacity of 1.0g of yam, we can use a simple equation:
q = m × c × ΔT
where q is the amount of heat required, m is the mass of the substance, c is the specific heat capacity, and ΔT is the change in temperature.
To measure the specific heat capacity of yam, we would first need to heat the yam to a known temperature, and then measure the amount of heat required to raise its temperature by a certain amount.
For example, we could heat 1.0g of yam to 25°C and then place it in a known amount of water at a lower temperature, such as 20°C. We could then measure the change in temperature of the water and calculate the amount of heat required to heat the yam.
By rearranging the equation above, we can solve for c:
c = q / (m × ΔT)
We can then substitute in the values we measured and calculate the specific heat capacity of the yam. This process can be repeated several times to obtain an average value for the specific heat capacity of yam.
To know more about Specific heat capacity, visit:
https://brainly.com/question/29766819#
#SPJ11
How do people tend to use land as the human population increases?
A. Developed land is converted to wetlands.
B. More land becomes available for wildlife habitats.
C. Urban land becomes cropland.
D. Grasslands are used for cropland
D. Grasslands are converted to cropland
As the human population grows, individuals use land in a variety of ways to suit their requirements, including housing, agriculture, industry, and transportation.
This usually results in more urbanization and the change of natural habitats to human-dominated environments. Some examples of common land-use shifts are:
D. Grasslands are converted to cropland: As food need grows, grasslands are frequently converted to cropland for agricultural production. This can result in soil degradation, biodiversity loss, and other environmental consequences.
As the human population expands, so does the need for resources and space, resulting in a variety of changes in land usage. The conversion of natural habitats such as forests and grasslands into human-dominated landscapes is one of the major land-use shifts.
This process, referred to as urbanization, frequently includes the creation of buildings, roads, and other infrastructure to support human activity. Furthermore, as the demand for food and other agricultural products grows, more land is converted to agriculture.
These land-use changes can have serious environmental consequences, such as habitat loss, soil degradation, and biodiversity loss. As a result, it is critical to think about the potential repercussions of land usage and design sustainable practices that balance human demands with environmental conservation.
learn more about the population here
https://brainly.com/question/29367909
#SPJ1
Calculate the equilibrium constant at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen. The data refer to
25°C.
CH4(9) + 2H20(9) = CO2(g) + 4H2(9)
Substance:
AH (kJ/mol)
AGf(kJ/mol)
S (J/K mol):
CH4(g)
-74. 87
-50. 81
186. 1
H2019)
-241. 8
-228. 6
188. 8
CO2(9)
-393. 5
-394. 4
213. 7
H219)
0
0
130. 7
The equilibrium constant (K) at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen is 8.04×10⁻¹³. This indicates that the reaction strongly favors the reactants, and very little of the products will be formed at equilibrium.
To calculate the equilibrium constant at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen, we use the formula:
[tex]Kc = \left(\frac{{[CO_2][H_2]^4}}{{[CH_4][H_2O]^2}}\right)[/tex]
where [ ] denotes concentration in moles per liter. We need to first determine the concentrations of the various species at equilibrium. For this, we use the Gibbs free energy change (ΔG) of the reaction, which is related to the equilibrium constant through the equation:
[tex]\Delta G^\circ = -RT \ln(Kc)[/tex]
where R is the gas constant (8.314 J/K mol), T is the temperature in Kelvin (25°C = 298 K), and ΔG° is the standard free energy change for the reaction, which can be calculated from the standard free energy of formation (ΔGf°) values of the reactants and products:
[tex]\Delta G^\circ = \sum n\Delta G_f^\circ(\text{products}) - \sum m\Delta G_f^\circ(\text{reactants})[/tex]
where n and m are the stoichiometric coefficients of the products and reactants, respectively. Using the given values, we get:
[tex]\Delta G^\circ = [1(-394.4) + 4(0)] - [1(-50.81) + 1(-241.8) + 2(0)][/tex]
ΔG° = -805.37 J/mol
Substituting this value and the other given values into the equation for ΔG°, we get:
[tex]Kc = e^(-ΔG°/RT)[/tex]
[tex]Kc = e^(-805.37/(8.314×298))[/tex]
Kc = 8.04×10⁻¹
Therefore, the equilibrium constant at 25°C for the reaction of methane with water to form carbon dioxide and hydrogen is 8.04×10⁻¹³.
To know more about the equilibrium constant refer here :
https://brainly.com/question/19671384#
#SPJ11
Explain use the tyndall effect to explain why it is more difficult to drive through
fog using high beams than using low beams.
The Tyndall effect is the scattering of light by colloidal particles or suspensions, causing the particles to become visible.
In fog, water droplets act as colloidal particles and scatter light, making it difficult to see clearly. High beams produce a greater amount of light, which causes more scattering and reflection in the fog, resulting in decreased visibility. This is because the water droplets in the fog are closer together and more concentrated in the path of the high beams, causing more light to be reflected back towards the driver's eyes.
Using low beams, on the other hand, produces less light and reduces the amount of scattering and reflection in the fog, resulting in better visibility. Therefore, it is recommended to use low beams when driving in foggy conditions to avoid glare and improve visibility.
To learn more about Tyndall effect, here
https://brainly.com/question/14431922
#SPJ4
Sort the disciptions of open clusters and globular clusters into the correct categories
Open clusters:
Found in the disk of the galaxyYoung starsFew hundred to a few thousand starsLoosely bound by gravityIrregular shapeGlobular clusters:
Found in the halo of the galaxyOld starsTens of thousands to millions of starsTightly bound by gravitySpherical shapeWhat are clusters?Clusters are collections of stars that are gravitationally connected to one another and close to one another in astronomy. Open clusters and globular clusters are the two basic categories into which they can be separated.
While globular clusters are collections of much older stars that are tightly bound together into a spherical shape, open clusters are collections of much younger stars that are relatively loosely bound together.
Find out more on open clusters here: https://brainly.com/question/15222665
#SPJ1
Select the most ideal gas situation:
Hydrogen and steam.
When hydrogen and steam are both present in a gas at the same pressure and temperature, this is the ideal gas condition. This is so because according to the ideal gas law, an ideal gas's pressure, volume, and temperature are all precisely proportional to one another.
This indicates that when the two gases have the same temperature and pressure, the two gases will also have the same volume. As a result, the gases are in their ideal state, having the same volume and pressure but retaining their distinct chemical compositions.
This is perfect because it enables the two gases to interact with one another in a predictable way, allowing for the measurement and prediction of the gases' behaviour.
Learn more about gases at:
https://brainly.com/question/1369730
#SPJ1
