A turntable rotates with a constant 1.85 rad/s2 clockwise angular acceleration. After 4.00 s it has rotated through a clockwise angle of 30.0 rad . Part A What was the angular velocity of the wheel at the beginning of the 4.00 s interval?

Answer: 10m

Explanation:

The magnitude of the vector would be 10

[tex]\sqrt{6^{2}+8^{2} } =10[/tex]

Answer:

a) 463.29 K

b) 8065.65 Pa

c) 0 J

Explanation:

The parameters given are;

Volume of the tank, V = 3.72 m³

Number of moles of gas present in the tank, n = 22.1 moles

Temperature of the gas before heating, T₁ = 300 k

Heat added to the gas, ΔQ = 4.5 × 10⁴ J

Specific heat capacity at constant volume, [tex]c_v[/tex], for monatomic gas = 12.47 J/K/mole

Avogadro's number = 6.022 × 10²³ particles per mole

a) ΔQ = n × [tex]c_v[/tex] × ΔT

Where:

ΔT = T₂ - T₁

T₂ = Final temperature of the gas

Hence, by plugging in the values, we have;

4.5 × 10⁴ = 22.1 × 12.47 × (T₂ - 300)

[tex]T_{2} - 300 = \frac{4.5\times 10^{4}}{22.1\times 12.47}[/tex]

T₂ = 300 + 163.29 = 463.29 K

b) The pressure of the gas is found from the relation;

P×V = n×R×T

[tex]P = \dfrac{n \times R \times T}{V}[/tex]

Where:

P = Pressure of the gas

R = Universal gas constant = 8.3145 J/(mol·K)

T = Temperature of the gas

V = Volume of the gas = 3.72 ³ (constant)

n = Number of moles of gas present = 22.1 moles (constant)

Hence the change in pressure is given by the relation;

[tex]\Delta P = \dfrac{n \times R \times (T_2 - T_1)}{V} = \dfrac{n \times R \times \Delta T}{V}[/tex]

Plugging in the values, we have;

[tex]\Delta P = \dfrac{22.1 \times 8.3145 \times 163.29}{3.72} = 8065.65 \, Pa[/tex]

c) Work done, W, by the gas is given by the area under the pressure to volume graph which gives;

W = f(P) × ΔV

The volume given in the question is constant

∴ ΔV = 0

Hence, W =  f(P) × 0 = 0 J

No work done by the gas during the process.

Answer:

Mg or your weight.

Explanation:

When your velocity is constant, the net force acting on you is 0. That means the upwards force of air resistance must fully balance the downwards force of gravity on you, which is Mg.

Explanation:

The first equation of motion in kinematics is given by :

[tex]v=u+at[/tex] .....(1)

u is initial speed

a is acceleration

v is final speed

t is time

Equation (1) is valid when the object is moving with constant acceleration. This equation gives relation between velocity and time.

Answer:

D

Explanation:

Now the net force is the applied force minus the frictional force; this is expressed mathematically as:

Fnet= Fappplied - Ffrictional

Now the frictional force is given as ;

Coefficient of friction × normal reaction

Normal reaction is the weight of the human acting in opposite direction.

Normal reaction of the human is ;

35 × 9.8 = 343N { note that weight = m× g and g= 9.8m/S2, a known standard }

Hence the Frictional force =343×0.4 =137.20N

Hence Fnet = 200-137.20 = 62.8N

Fnet = 63N to the nearest whole

The net force on the couch as it slides is  63N.

What is frictional force?

When an object is moving on a rough surface, it experiences opposition. This opposing force is called the friction force.

The friction force is given by

f = coefficient of friction x Normal force

Given, the coefficient of kinetic friction between a couch and the floor is 0.4. If the couch has a mass of 35 kg and you push it with a force of 200 N.

Normal reaction is the weight of the human acting in opposite direction.

Normal reaction N =35 × 9.8 = 343N

Frictional force f =0.4 x 343

                          f =137.20N

The net force will be

Fnet= Fappplied - Ffrictional

Fnet = 200-137.20 = 62.8N

Fnet = 63N

Thus,  the net force on the couch as it slides is  63N.

Learn more about friction force.

https://brainly.com/question/1714663

#SPJ2

Answer:

Vf = 0.0017 m³ = 1.7 L

Explanation:

The work done by the system on the surrounding at constant pressure is given by the following formula:

W = PΔV

W = P(Vf - Vi)

where,

W = Work done = 288 J

P = Constant Pressure = (2 atm)(101325 Pa/atm) = 202650 Pa

Vf = Final Volume f Cylinder = ?

Vi = Initial Volume of Cylinder = (0.25 L)(0.001 m³/ 1 L) = 0.00025 m³

Therefore,

288 J = (202650 Pa)(Vf - 0.00025 m³)

Vf = 288 J/202650 Pa + 0.00025 m³

Vf = 0.0017 m³ = 1.7 L

Answer:

The ratio is  [tex]\frac{F_{T1}}{F_{T2}} = 2[/tex]

Explanation:

The diagram for this question is shown on the first uploaded image

Here we are assume the acceleration of the train is a

which makes the acceleration of each car a

From the question we are told that

      Considering the second car

 The force causing it s movement  is mathematically represented as

       [tex]F_{T2} = ma[/tex]

 Considering the first car

 The force causing it s movement  is mathematically represented as

      [tex]F = F_{T1} -F_{T2} = ma[/tex]

=>   [tex]F_{T1} -ma = ma[/tex]

=>   [tex]F_{T1} = 2 ma[/tex]

=> [tex]\frac{F_{T1}}{ma} = 2[/tex]

=> [tex]\frac{F_{T1}}{F_{T2}} = 2[/tex]

Answer: it's weight decreases

Explanation:

Question:

A particle moving along the x-axis has a position given by x=(24t - 2.0t³)m, where t is measured in s. What is the magnitude of the acceleration of the particle at the instant when its velocity is zero

Answer:

24 m/s

Explanation:

Given:

x=(24t - 2.0t³)m

First find velocity function v(t):

v(t) = ẋ(t) = 24 - 2*3t²

v(t) = ẋ(t) = 24 - 6t²

Find the acceleration function a(t):

a(t) = Ẍ(t) = V(t) = -6*2t

a(t) = Ẍ(t) = V(t) = -12t

At acceleration = 0, take time as T in velocity function.

0 =v(T) = 24 - 6T²

Solve for T

[tex] T = \sqrt{\frac{-24}{6}} = \sqrt{-4} = -2 [/tex]

Substitute -2 for t in acceleration function:

a(t) = a(T) = a(-2) = -12(-2) = 24 m/s

Acceleration = 24m/s

The correct answer is D. electric current being forced uphill by the battery back to the positive terminal.

What is Electric Current?

Electric current is the flow of electric charge through a conducting medium, such as a wire, due to the movement of electrons or ions. The flow of charge is typically caused by the presence of an electric field that creates a potential difference (voltage) between two points in a circuit

In an electrical circuit, pipes are analogous to wires or conductive paths that allow the flow of electric current. The flow of electric current is from the positive terminal of the battery to the negative terminal, which is opposite to the direction of conventional current flow. Therefore, option C is incorrect.

Learn more about Electric Current

https://brainly.com/question/1100341

#SPJ1

Answer:

ΔE = ‒0.271 kJ

Explanation:

Let's begin by listing out the given variables:

q = -0.653 kJ, w = 0.389 kJ

Using the formula ΔE = q + w

ΔE = -0.653 + 0.388

ΔE = (‒0.655 + 0.382) kJ

ΔE = ‒0.271 kJ

Therefore, the change in internal energy is -271 J or -0.271 kJ which implies that the system is exothermic

Answer:

a. 900 J

b. 0.383

Explanation:

According to the question, the given data is as follows

Horizontal force = 150 N

Packing crate = 40.0 kg

Distance = 6.00 m

Based on the above information

a. The work done by the 150-N force is

[tex]W = F x = \mu N x = \mu\ m\ g\ x[/tex]

[tex]W = 150 \times 6[/tex]

= 900 J

b. Now the coefficient of kinetic friction between the crate and surface is

[tex]\mu = \frac {F}{m\timesg}[/tex]

[tex]= \frac{150}{40\times 9.8}[/tex]

= .383

We simply applied the above formulas so that each one part could calculate

We want to find the work and kinetic friction for the given situation. The solutions are:

Here we have a horizontal force of 150N pushing a 40.0 kg packing crate a distance of 6.00m at a constant speed.

a) First we want to find the work, it is given by the force applied times the distance moved, so the work is just:

W = 150N*6.00m = 900 N*m

b) Now we want to find the coefficient of kinetic friction, it must be such that the kinetic friction force is equal to the pushing force, in this way there is no net force, and then there is no acceleration.

Remember that the friction force is:

F = m*g*μ

Where:

Then we must solve:

150N = 40kg*(9.8 m/s^2)*μ = 392N*μ

150N/392N = 0.38

So the coefficient of kinetic friction between the crate and the surface is 0.38

If you want to learn more about forces, you can read:

https://brainly.com/question/13370981

Answer:

4.09 MeV

Explanation:

Find the given attachment

Answer:

v = 7.67 m/s

Explanation:

The equation for apparent weight in the situation of weightlessness is given as:

Apparent Weight = m(g - a)

where,

Apparent Weight = 360 N

m = mass passenger = 61.2 kg

a = acceleration of roller coaster

g = acceleration due to gravity = 9.8 m/s²

Therefore,

360 N = (61.2 kg)(9.8 m/s² - a)

9.8 m/s² - a = 360 N/61.2 kg

a = 9.8 m/s² - 5.88 m/s²

a = 3.92 m/s²

Since, this acceleration is due to the change in direction of velocity on a circular path. Therefore, it can b represented by centripetal acceleration and its formula is given as:

a = v²/r

where,

a = centripetal acceleration = 3.92 m/s²

v = speed of roller coaster = ?

r = radius of circular rise = 15 m

Therefore,

3.92 m/s² = v²/15 m

v² = (3.92 m.s²)(15 m)

v = √(58.8 m²/s²)

v = 7.67 m/s

Answer:

b and e

Explanation:

r x F is the formula for torque.

The "turning effect" or torque happens when concentric forces rotate an object along said center.

a) False because T = Fr = Ia (a = angular acceleration)

b) True

c) False. L = Iw (w = angular velocity), which does not equal Ia

d) False. It is torque, not the product of torque and something else

e) True.

Answer:

Thus, the energy stored by a 50 Ampere minute battery is found to be  36 KJ.

Explanation:

The power delivered by a battery is given by the formula:

P = VI

where,

P = Power Delivered by battery in 1 second

V = Voltage of battery = 12 volt

I = Current stored in battery

But, if we multiply both sides of equation by time (t), then:

Pt = VIt

where,

Pt = Power x Time = E = Energy Stored = ?

It = Rating of Battery = (50 A.min)(60 sec/min) = 3000 A.sec

Therefore,

E = (12 volt)(3000 A.sec)

E = 36000 J = 36 KJ

Thus, the energy stored by a 50 Ampere minute battery is found to be  36 KJ.

Answer:

24 Newtons

Explanation:

The force exerted in the middle cube needs to be enough to move the middle cube and the right cube with an acceleration of 2 m/s2.

The mass of those two cubes combined is 6 + 6 = 12 kg

So, using the following equation, we can find the force:

Force = mass * acceleration

Force = 12 * 2

Force = 24 Newtons

Answer:

normal force = 10 N

Explanation:

Given data

frictional force = 0.400 N

coefficient of kinetic friction = 0.04

Solution

we get here normal force that is express as

normal force = [tex]\frac{Frictional\ force}{coefficient\ of\ friction}[/tex]        ............1

put here value and we will get value

normal force = [tex]\frac{0.400}{0.04}[/tex]  

solve it we get

normal force = 10 N

Answer:

13.9 kJ

Explanation:

Given that

Length of the side, l = 1.8 m

Drag coefficient, C(d) = 1.4

Distance of run, d = 200 m

Velocity of run, v = 5 m/s

Density, ρ = 1.23

Using the Aerodynamics Drag Force formula. We have

F(d) = 1/2.ρ.A.C(d).v²

The Area, A needed is 1.8 * 1.8 = 3.24 m². So that,

F(d) = 1/2 * 1.23 * 3.24 * 1.4 * 5²

F(d) = 139.482/2

F(d) = 69.74

recall that, energy =

W = F * d

W = 69.74 * 200

W= 13948

W = 13.9kJ

Therefore, the thermal energy added to the air by the drag force is 13.9kJ

Answer:

v = 3.33 m/s

Explanation:

In the position of 45 degrees, all the energy of the rock is gravitational, then we have:

E = m*g*L*cos(angle)

and in the vertical position of the string, all the energy is kinetic, so we have:

E = m*v^2/2

If there is no dissipation, both energies are equal, so we have:

m*g*L*cos(45) = m*v^2/2

9.81 * 0.8 * 0.7071 * 2 = v^2

v^2 = 11.0986

v = 3.33 m/s

Answer:

10 metres

Explanation:

So, we are given the following data or parameters or information which is going to assist us in solving this particular problem or Question efficiently.

=> The speed of the space ship can be found from this relationship: ✓(1 - [v^2/c^2] ) = 1/2.

=> The length of the space ship = 20 m.

=> Assumption = '' If the length of the ship is measured by the inertial earth-bound observer".

Thus, from the speed of the space ship can be found from this relationship we can determine the value;

✓(1 - [v^2/c^2] ) = 1/2.

V = 20 × 1/2 = 10 metres.

Note that we use the contraction formula to solve for V.

Answer:

a. 200 m

b. 100 m

Explanation:

Solution:-

- We will first draw three points marked A,B and Q from left most to right most.

- We are told that the antennas at A and B radiate in phase. This means the radio-waves emitted by each antenna are synchronous in terms of ( frequency and wavelength ).

- We will denote the common wavelength of coherent sources of radio-waves ( A and B ) with λ.

- The relation between the wavelength ( λ ) and the path difference between the source and observation point ( Q ) for the case of destructive interference is:

                             AQ - BQ = n*λ/2

Where,

             n: The order of wavelength

             AQ: The distance between antenna A and point Q

             BQ: The distance between antenna B and point Q

- The point Q is positioned ( 100 + 50 ) m away from antenna A and 50 m from antenna B. Hence,

                            150 - 50 = n*λ/2

- To determine the longest wavelength ( λ ) to meet destructively at point Q with the given path difference. The order of wavelength ( n ) must be minimum ( 1 ). Therefore,

                           100 = λ/2

                           λ = 200 m  .... Answer

- The relation between the wavelength ( λ ) and the path difference between the source and observation point ( Q ) for the case of constructive interference is:

                             AQ - BQ = n*λ

Where,

             n: The order of wavelength

             AQ: The distance between antenna A and point Q

             BQ: The distance between antenna B and point Q

- The point Q is positioned ( 100 + 50 ) m away from antenna A and 50 m from antenna B. Hence,

                            150 - 50 = n*λ

- To determine the longest wavelength ( λ ) to meet constructively at point Q with the given path difference. The order of wavelength ( n ) must be minimum ( 1 ). Therefore,

                           100 = λ

                           λ = 100 m  .... Answer

Answer:

The angle of refraction of sheet 3 when sheet 1 is on top of it is [tex]\theta_{r_s } = 23.1 ^o[/tex]

Explanation:

From the question we are told that

     The angle of incidence is  [tex]\theta _i = 26.50 ^o[/tex]

      The angle of refraction angle for  sheet 1 is  [tex]\theta _{r_1}} = 31.70 ^o[/tex]

       The angle of refraction for sheet 3 is  [tex]\theta _{r_3}} = 36.70 ^o[/tex]

According to Snell's  law  

       [tex]\frac{n_2}{n_1} = \frac{sin (\theta_1)}{sin (\theta_{r_1})}[/tex]

Where  [tex]n_1 \ and \ n_2[/tex]  are refractive index of sheet 1  and  sheet 2  

       =>   [tex]n_2 = n_1 \frac{sin(\theta_i)}{sin (\theta _{r_1})}[/tex]

Also  when sheet 3 in on top of sheet 2

       [tex]\frac{n_2}{n_3} = \frac{sin \theta_i}{sin \theta_{r_3}}[/tex]

substituting for  [tex]n_2[/tex]

      [tex]n_1 \frac{sin(\theta_i)}{sin (\theta _{r_1})} = n_3 \frac{sin \theta_i}{sin \theta_{r_3}}[/tex]

      [tex]n_1 \frac{sin(\theta_i)}{sin (\theta _{r_1})} = n_3 \frac{sin \theta_i}{sin \theta_{r_3}}[/tex]

=>    [tex]n_3 = n_1 * \frac{sin(\theta_{r_3})}{sin(\theta_{r_1})}[/tex]

when sheet 1 in on top of sheet 3

        [tex]\frac{n_3}{n_1} = \frac{sin(\theta_i)}{\theta_{r_s}}[/tex]

where [tex]r_s[/tex] is the angle of refraction when sheet 1 is on top of sheet 3

substituting for  [tex]n_3[/tex]

         [tex]\frac{ n_1 * \frac{sin(\theta_{r_3})}{sin(\theta_{r_1})}}{n_1} = \frac{sin(\theta_i)}{\theta_{r_s}}[/tex]

=>   [tex]sin (\theta _{r_s}) = n_1 * sin (\theta_i) * \frac{sin (\theta_{r_1})}{ n_1 * sin(\theta_{r_3})}[/tex]

substituting values

      [tex]sin (\theta _{r_s}) = n_1 * sin (26.50) * \frac{sin (31.70)}{ n_1 * sin(36.70)}[/tex]

=>     [tex]\theta_{r_s } = sin^{-1} (0.3923)[/tex]

=>   [tex]\theta_{r_s } = 23.1 ^o[/tex]

Complete question is;

Assuming 100% efficient energy conversion how much water stored behind a 50 centimeter high hydroelectric dam would be required to charge the battery with power rating, 12 V, 50 Ampere-minutes.

Answer:

Amount of water required to charge the battery = 7.35 m³

Explanation:

The formula for Potential energy of the water at that height = mgh

Where;

m = mass of the water

g = acceleration due to gravity = 9.8 m/s²

h = height of water = 50 cm = 0.5 m

We know that in density, m = ρV

Where;

ρ = density of water = 1000 kg/m³

V = volume of water

So, potential energy is now given as;

Potential energy = ρVgH = 1000 × V × 9.8 × 0.5 = (4900V) J

Now, formula for energy of the battery is given as;

E = qV

We are given;

q = 50 A.min = 50 × 60 = 3,000 C

V = 12 V

Thus;

qV = 3,000 × 12 = 36,000 J

E = 36,000 J

At a 100% conversion rate, the energy of the water totally powers the battery.

Thus;

(4900V) = (36,000)

4900V = 36,000

V = 36,000/4900

V = 7.35 m³

Answer:

They had the same speed.

Explanation:

It won't be velocity, because velocity is a vector quantity. Speed is scalar.

Velocity is the rate of change of displacement. During their periods of travel, the cars definitely had the same velocity.

Velocity is the directional speed of a moving object as an indicator of its rate of change in location as perceived from a certain frame of reference and measured by a specific time standard.

Given that the first car travels 40 meters due east in 5 seconds. Therefore, we can write,

Distance = 40 meters

Time = 5 seconds

Velocity = Distance / Time = 40 meter/ 5 sec = 40 m/sec

Also, given that the second car travels 64 meters due west in 8 seconds. Therefore, we can write,

Distance = 64 meters

Time = 8 seconds

Velocity = Distance / Time = 64 meter/ 8 sec = 8 m/sec

Hence, During their periods of travel, the cars definitely had the same velocity.

Learn more about Velocity here:

https://brainly.com/question/18084516

#SPJ2

Answer:

A.  xmax = 131.49 m

B.  t = 8.74 s

C.  ymax = 220.33 m

Explanation:

A. In order to find the horizontal distance which cannon travels you first calculate the flight time. The flight time can be calculated by using the following formula:

[tex]y=y_o+v_osin\theta-\frac{1}{2}gt^2[/tex]      (1)

yo: height from the projectile is fired = 200m

vo: initial velocity of the projectile = 25m/s

g: gravitational acceleration = 9.8 m/s^2

θ: angle between the direction of the initial motion of the ball and the horizontal = 53°

t: time

You need the value of t when the projectile hits the ground. Then, in th equation (1) you make y = 0m.

When you replace the values of all parameters in the equation (1), you obtain the following quadratic formula:

[tex]0=200+(25)sin53\°t-\frac{1}{2}(9.8)t^2\\\\0=200+19.96t-4.9t^2[/tex] (2)

You use the quadratic formula to obtain the value of t:

[tex]t_{1,2}=\frac{-19.96\pm\sqrt{(19.96)^2-4(-4.9)(200)}}{2(-4.9)}\\\\t_{1,2}=\frac{-19.96\pm65.71}{-9.8}\\\\t_1=8.74s\\\\t_2=-4.66s[/tex]

You use the positive value because it has physical meaning.

Now, you can calculate the horizontal range of the projectile by using the following formula:

[tex]x_{max}=v_ocos\theta t[/tex]      

[tex]x_{max}=(25m/s)(cos53\°)(8.74s)=131.49m[/tex]

The cannon ball travels a horizontal distance of 131.49 m

B. The cannon ball reaches the canon for t = 8.74s

C. The maximum height is obtained by using the following formula:

[tex]y_{max}=y_o+\frac{v_o^2sin^2\theta}{2g}[/tex]     (3)

By replacing in the equation (3) the values of all parameters you obtain:

[tex]y_{max}=200m+\frac{(25m/s)^2(sin53\°)^2}{2(9.8m/s^2)}\\\\y_{mac}=200m+20.33m=220.33m[/tex]

The maximum height reached by the cannon ball is 220.33m

Answer:

Explanation:

During slowing down , initial angular velocity ω₁ = 22 rad /s

final angular velocity ω₂ = 13.5 rad /s

using the law's of motion formula for rotation

ω₂² =  ω₁² + 2 αθ  , α is angular acceleration and θ is angle in radian rotated during this period

13.5² = 22² - 2xα x 13.8

2xα x 13.8 = 484 - 182.25

α  =  10.93 rad / s²

Answer:

C = 44.75 x 10⁻⁸ F

Explanation:

Assuming no loss of energy between capacitor and inductor

energy in inductor initially = 1/2 Li₀² where L is inductance and i₀ is peak current .

= .5 x 6 x 10⁻³ x .57²

= .97 x 10⁻³ J .

This energy is transferred to capacitor .

energy of capacitor = 1/2 CV²

= .5 x C x 66²

= 2178 C

2178C = .97 x 10⁻³

C = 44.75 x 10⁻⁸ F .

The magnetic energy stored in the inductor is transformed into electrical energy stored in the capacitor. The value of capacitance for the given circuit is 44.75 x 10⁻⁸ F

According to the law of conservation of energy, the magnetic energy stored in the inductor will be gradually lost and this energy will be stored in the capacitor as electrical energy.

Initially, the energy in the inductor is:

E = 1/2 Li₀²

where L is inductance

and i₀ is peak current.

E = 0.5 × 6 × 10⁻³ × (0.57)²

E = 0.97 × 10⁻³J

This energy is transformed into electrical energy stored in the capacitor.

So the capacitor energy is:

E = 1/2 CV²

where C is the capacitance

E = 0.5 × C × 66²

E = 2178 C

0.97 x 10⁻³ = 2178 C

C = 44.75 x 10⁻⁸ F

Learn more about capacitance:

https://brainly.com/question/12356566?referrer=searchResults

Answer:

t = 25.5 min

Explanation:

To know how many minutes does Richard save, you first calculate the time that Richard takes with both velocities v1 = 65mph and v2 = 80mph.

[tex]t_1=\frac{x}{v_1}=\frac{150mi}{65mph}=2.30h\\\\t_2=\frac{x}{v_2}=\frac{150mi}{80mph}=1.875h[/tex]

Next, you calculate the difference between both times t1 and t2:

[tex]\Delta t=t_1-t_2=2.30h-1.875h=0.425h[/tex]

This is the time that Richard saves when he drives with a speed of 80mph. Finally, you convert the result to minutes:

[tex]0.425h*\frac{60min}{1h}=25.5min=25\ min\ \ 30 s[/tex]

hence, Richard saves 25.5 min (25 min and 30 s) when he drives with a speed of 80mph

The average acceleration [tex]\vec a_{\rm ave}[/tex] over some time interval [tex][t_1,t_2][/tex] is equal to the ratio of the change in velocity [tex]\vec v_2-\vec v_1[/tex] over the duration of the interval [tex]t_2-t_1[/tex], or

[tex]\vec a_{\rm ave}=\dfrac{\Delta\vec v}{\Delta t}=\dfrac{\vec v_2-\vec v_1}{t_2-t_1}[/tex]

which can be split into the [tex]x[/tex] and [tex]y[/tex] components as

[tex]a_{\rm{ave},x}=\dfrac{v_{2,x}-v_{1,x}}{t_2-t_1}=\dfrac{-170\frac{\rm m}{\rm s}-90\frac{\rm m}{\rm s}}{30.0\,\mathrm s-0}\approx-8.67\dfrac{\rm m}{\mathrm s^2}[/tex]

[tex]a_{\rm{ave},y}=\dfrac{v_{2,y}-v_{1,y}}{t_2-t_1}=\dfrac{40\frac{\rm m}{\rm s}-110\frac{\rm m}{\rm s}}{30.0\,\mathrm s-0}\approx-2.33\dfrac{\rm m}{\mathrm s^2}[/tex]

The magnitude of this average acceleration is

[tex]\left\|\vec a_{\rm ave}\right\|=\sqrt{{a_{\rm{ave},x}}^2+{a_{\rm{ave},y}}^2}\approx8.98\dfrac{\rm m}{\mathrm s^2}[/tex]

and its direction is [tex]\theta[/tex] such that

[tex]\tan\theta=\dfrac{a_{\rm{ave},y}}{a_{\rm{ave},x}}\implies\theta\approx-164.9^\circ[/tex]

which corresponds to a direction of about 15.1º South of West.