The magnitude of the magnetic force acting on the charge is 2.34×10⁻³ N.
What is magnetic force?
A magnetic force is the force that act in a magnetic field.
To calculate the magnetic force, we use the formula below.
Formula:
F = qvB.........Equation 1Where:
F = magnetic forceq = point chargev = Velocity of the the chargeB = Field strengthFrom the question,
Given:
q = 5.0×10⁻⁷ Cv = 2.6×10⁵ m/sB = 1.8×10⁻² TSubstitute these values into equation 2
F = (5.0×10⁻⁷)(2.6×10⁵)(1.8×10⁻²)F = 23.4×10⁻⁴F = 2.34×10⁻³ NHence, the magnitude of the magnetic force acting on the charge is 2.34×10⁻³ N.
Learn more about magnetic force here: https://brainly.com/question/2279150
#SPJ12
as time passes the sound wave
Answer:
Loud to soft while pitch increases
Explanation:
Sound waves shown graphically display their amplitude (height of the graph) and their wavelength (the horizontal distance from peak to peak, or valley to valley... one full cycle).
Instead of wavelength, alternatively, one can observe the frequency of the wave (how many cycles are completed for a given unit of horizontal distance) which is in an inverse relationship with the wavelength (as a wavelength gets shorter, the frequency gets higher, and as the wavelength gets longer, the frequency gets lower).
The amplitude of a wave corresponds to how loud the sound is.
The frequency of a wave corresponds to the pitch of the sound.
Notice that on the graph, the height of the graph decreases over time (the peaks get shorter and shorter). So, the sound volume will get quieter and quieter. Using terminology that matches the answer choices, the sound will start loud and get soft.
Notice that on the graph, the wavelength decreases over time (starts with a pretty long distance between peaks, and then the distance between peaks gets shorter and shorter). Alternatively, looking at frequency, notice that the frequency gets higher and higher (on the left, one finger-width doesn't is less than one full cycle, but on the right, the same finger-width is wider than multiple cycles). So, the pitch of the sound will get higher and higher.
Thus, for this graph, the sound goes from loud to soft, and the pitch increases.
Science question! helppppp
Let's take this problem step-by-step:
What does this problem want to solve:
⇒ find two pendulums that will swing back and forth in the least amount
of time
Therefore:
⇒ must find the equation that calculates that period or swing time of a
pendulum
Equation: [tex]T = 2\pi \sqrt{\frac{L}{g} }[/tex]
L: length of the pendulumg: gravitational accelerationBased on the equation:
⇒ the longer the string is ⇒ the greater the swing time
Thus:
⇒ pendulum Y and Z will have the least amount of swing time
Answer: (B)
Hope that helps!
#LearnwithBrainly
what is periscope ? where it is used?
Explanation:
The periscope is used in the submarines to see what is going on the water surface.
It is also used in some gun turrets and it is used in armed vehicles.
✨Hope it helps.✨
a A load of 1000 N can be lifted by applying
the force) effort of 250 N.If the load
arm is 25 cm, calculate the effort arm.
Answer:
Explanation:
[tex]\text{Since the fulcrum lies in between the load and effort, it is class I lever.}[/tex]
[tex]\text{Mechanical advantage (M.A.) of levers is given by,}[/tex]
[tex]\text{M.A.=effort armload arm=50cm,10cm}[/tex]
[tex]\text{Thus, mechanical advantage , M.A. = 5.}[/tex]
[tex]\text{Given, effort (E)=10N, Load(L)=?}[/tex]
∴ [tex]L=E \times M.A.[/tex]
[tex]=10\times5=50N[/tex]
Answer:
[tex]\fbox {100 cm}[/tex]
Explanation:
Finding Mechanical Advantage :
MA = Load / Effort
MA = 1000/250
MA = 4
Finding length of effort arm :
Load arm = Effort arm / 4
Effort arm = 25 cm x 4
Effort arm = 100 cm
A woman takes her dog rover for a walk on a leash. She pulls on the leash with a force of 30.0 N at an angle of 29° above the horizontal sidewalk. What force is tending to lift Rover vertically off the ground?
Please help I'm stuck.
19.8 N force is tending to lift Rover vertically off the ground.
What is horizontal and vertical component?The horizontal velocity component ([tex]v_{x}[/tex]) describes the influence of the velocity in displacing the projectile horizontally. The vertical velocity component ([tex]v_{y}[/tex]) describes the influence of the velocity in displacing the projectile vertically.
According to the question,
The women pulls the dog with a force of 30 N at an angle of 29° from the horizontal.
Horizontal component= 30cos(29°) = 22.2 N
Vertical component = 30sin(29°) = 19.8 N
Therefore,
The horizontal component would tend to make the dog move forward and the vertical component would tend lift it off the ground.
Hence,
19.8 N force is tending to lift Rover vertically off the ground.
Learn more about horizontal and vertical component here:
https://brainly.com/question/11776718
#SPJ1
Why is it important to have a closed circuit?
A. It prevents a circuit from working.
B. It prevents components from overheating.
C. It increases the resistance in the circuit.
D. It allows an electric current in the circuit.
D. It allows the flow of an electric current in the circuit.
Why is it important to have a closed circuit?Closed circuit allows the flow of current in the circuit from the battery to the bulb. If the circuit is open then the current will not reach to the bulb or other appliances.
So we can conclude that It is important to have a closed circuit because it allows the flow of an electric current in the circuit.
Learn more about circuit here: https://brainly.com/question/2969220
#SPJ1
This state that the work done on a body by a net force is equal to the change is kinetic energy of the body
Answer:
that's true The work-energy theorem states that
Calculate the mass of an object whose weight is 400n and accleration due to gravity is 10 m/ s
Answer:
40kg
Explanation:
w=m×
w=400n
g=10
m=?
400/10=m×10/10
m=40
ons: READ each question below and ANSWER each part of the question.
Questions:
1. Ms. Woodard walks 1 m between each desk in her classroom. She walks
from desk 1 to desk 3, from desk 3 to desk 4, and finally from desk 4 back to
desk 2.
a. DRAW Ms. Woodard's path to all the desks here:
a.
a.
What DISTANCE has Ms. Woodard traveled? CONVERT (change) your answer to
millimeters.
What is Ms. Woodard's DISPLACEMENT?
Ms. Woodard has traveled a distance of 5 m.
Ms. Woodard's displacement is 1 m.
What type of facility has a frequency of 108.15 MHz?
ILS is a type of facility that has a frequency of 108.15 Megahertz.
What is an ILS?ILS is an acronym for instrument landing system and it can be defined as a precision radio navigation system that is designed and developed to provide an aircraft (airplane) with short-range guidance, so as to enable it approach a runway during bad weather or at night.
Generally, ILS uses two main directional radio signals and these include:
The localizer: it uses a frequency of 108 to 112 MHz for horizontal guidance.The glideslope: it uses a frequency of 329.15 to 335 MHz for vertical guidance.Read more on instrument landing system here: https://brainly.com/question/19091395
#SPJ12
You are trying to measure the mass of several different objects when you realize that there is a large wad of gum stuck to the underside of the balance pan. Removing the gum will improve the __________ of your measurements.
Answer:
accuracy
Explanation:
You are trying to measure the mass of several different objects when you realize that there is a large wad of gum stuck to the underside of the balance pan. Removing the gum will improve the accuracy of your measurements.
NEED ANSWER ASAP!!! Angela has a bucket of mass 2 kg tied to a string. She places a drinking glass of mass 0.5 kg in the bucket. She spins the bucket in a vertical circle of radius 1.5 m. You want to find out how fast she must swing the bucket to keep the glass from falling out.
a. Draw the free-body diagram for the glass when it is at the top of the circle.
b. What is the equation for the net force on the glass at the top of the circle in terms of w, Fn, m, v, and r?
c. The glass will fall out of the bucket if the normal force between the glass and bucket equals zero. How fast must she spin the bucket to prevent this from happening?
d. The string will break if the tension on it is more than 100 N. Over what range of speeds can she keep the glass in the bucket and prevent the string from breaking?
a. The free-body diagram for the glass when it is at the top of the circle is attached below.
b. The equation for the net force on the glass at the top of the circle in terms of w, Fn, m, v, and r is mg x g + N - mg x Vtop² /R =0
c. The glass will fall out of the bucket if the normal force between the glass and bucket equals zero. The speed with which she spin the bucket to prevent this from happening is 3.83 m/s.
d. The string will break if the tension on it is more than 100 N. The range of speeds can prevent the string from breaking is 3.83< Vtop<4.99 m/s
What is Net force?When two or more forces are acting on the system of objects, then the to attain equilibrium, net force must be zero.
Given, Angela has a bucket of mass 2 kg tied to a string. She places a drinking glass of mass 0.5 kg in the bucket. She spins the bucket in a vertical circle of radius 1.5 m. She must swing the bucket to keep the glass from falling out.
a. The free body diagram of the bucket and glass is attached below.
b. Bucket will undergo centrifugal force
Fb = mVtop² /R
From the equilibrium of forces, we have
For bucket,
T +mb xg - N = mb x Vtop² /R..............(1)
For glass,
mg x g + N = mg x Vtop² /R..............(2)
Thus, this is the net force equation on the glass.
c. On adding both the equations. we have
T + (mb + mg) xg = (mb + mg) Vtop² /R
Substituting the values, T = 0 and from the question, we get
0 + (2+0.5) 9.81 = (2+0.5)(Vtop²/0.5)
Vtop = 3.83 m/s
Thus, the speed of spin to prevent glass from falling out is 3.83 m/s
d. The string will break if the tension on it is more than 100 N
100 + (2+0.5) 9.81 = (2+0.5)(Vtop²/0.5)
Vtop = 4.99 m/s
Thus, the range of velocity is 3.83< Vtop<4.99 m/s
Learn more about net force.
https://brainly.com/question/18031889
#SPJ1
8. An electrical resistor immersed in a liquid produces 65.0 W of electrical energy for 120
specific heat capacity of the liquid in this temperature range. Assume that negligible h
O
O
O
2.51 x 10³ J/(kg. C°)
1.67 x 106 J/(kg C°)
2.02 x 104 J/(kg. C°)
The specific heat capacity of the liquid is 2.51 x 10³ J/kg⁰C.
Specific heat capacity of the liquidThe specific heat capacity of the liquid is calculated as follows;
Q = mcΔФ
where;
Q is quantity of heat c is specific heat capacitym is mass of the liquidΔФ is change in temperature = 22.54 - 18.55 = 3.99 ⁰Cc = Q/mΔФ
c = (65 x 120)/(0.78 x 3.99)
c = 2.51 x 10³ J/kg⁰C
The complete question is below:
An electrical resistor immersed in a liquid produces 65.0 W of electrical energy for 120 s. The mass of the liquid is 0.780 kg and its temperature increases from 18.55°C to 22.54°C. a) Find the average specific heat capacity of the liquid in this temperature range.
Learn more about specific heat capacity here: https://brainly.com/question/16559442
#SPJ1
What is the term for producing a current by moving a wire through a magnetic field?.
You should switch your headlights from high beam to low beam when a vehicle approaching from the opposite direction gets no closer than____ feet away from you.
You should switch your headlights from high beam to low beam when a vehicle approaching from the opposite direction gets no closer than 492.126 feet away from you.
What is a low beam?Low beams, often known as dipped beams have a close-range focus. The most crucial and commonly utilized beam in an automobile is the low beam.
When a car coming from the other direction is no closer than 492.126 feet away from you, you should lower your headlights from high to low beam.
Hence, a vehicle approaching from the opposite direction gets no closer than 492.126 feet away from you.
To learn more about the low beam refer;
https://brainly.com/question/11531917
#SPJ1
what is the speed of a wave that has a frequency of 11.5Hz and a wavelength of 1.7m?
Answer:
19.55 m/s
Explanation:
Here is HOW to get the answer:
Speed = wavelength * freq
= 1.7 * 11.5 = 19.55 m / s
When the inferior angle of the scapula moves in the superior and lateral direction, the motion is called:
The motion of the inferior angle of the scapula in the superior and lateral direction is called upward rotation.
What are the possible motions of the scapula?The scapula or the shoulder blade has about six different types of motion it undergoes.
The six ways of movement of the scapula are:
protraction,retraction,elevation,depression,upward rotation, anddownward rotationWhen the inferior angle of the scapula moves in the superior and lateral direction, the motion is called upward rotation.
Learn more about scapula motion at: https://brainly.com/question/16868917
#SPJ12
2. A kg of iron and a kilo of lead, both at 1000 degrees Celsius, are kept on ice. It is discovered after some time that the iron has melted more ice than the lead. Why? 2 A vonal containing un or in kont in on oron The tomis motor an hoot
The specific heat capacity of iron is greater than that of lead hence the iron will melt the ice more than the lead.
What is the specific heat capacity?
The specific heat capacity refers to the amount of heat that is required to raise the temperature of 1Kg of a body by 1 K.
We know that the specific heat capacity of iron is greater than that of lead hence the iron will melt the ice more than the lead.
Learn more about heat capacity:https://brainly.com/question/13499849
#SPJ1
Which statement about polymers is true?
Options below:
-Polymers are substances that have relatively large molecules.
-Oil and gas are the starting materials for making all polymers.
-Fabrics such as cotton and silk are synthetic polymers.
-All polymers are obtained from living organisms.
Answer:
a
Explanation:
Polymers are large molecules which form long chains
Answer: A. Polymers are substances that have relatively large molecules.
Explanation:
Select the correct answer.
Which statement about polymers is true?
A. Polymers are substances that have relatively large molecules.
B. Oil and gas are the starting materials for making all polymers.
C. Fabrics such as cotton and silk are synthetic polymers.
D. All polymers are obtained from living organisms.
The actual mass of a sheet of copy paper is 4.5 g. What must be the actual mass of a 1 cm² plece of copy paper?
Show your calculations.
The mass of 1 cm² piece of copy paper is 0.0072 g.
What is the area of a piece of paper?Assuming the dimensions of a piece of paper is 21.0 x 29.7 cm
The area of the piece of paper = 21.0 * 29.7 = 623.7 cm²
Mass of 623.7 cm² = 4.5 g
Mass of 1 cm² piece of copy paper = 4.5/623.7 cm² = 0.0072 g
Therefore, the mass of 1 cm² piece of copy paper is 0.0072 g.
Learn more about area at: https://brainly.com/question/25965491
#SPJ1
Find the maximum energy stored in the spring bumpers
The maximum energy stored in the spring bumpers is given as ¹/₂kx².
Maximum energy stored in a springThe maximum energy stored in a spring is given by the following equations;
E = ¹/₂kx²
where;
E is the energy stored in the springk is spring constantx is extension of the springThus, the maximum energy stored in the spring bumpers is given as ¹/₂kx².
Learn more about energy stored in spring here: https://brainly.com/question/20762015
#SPJ12
A passenger is running inside a stationary train with some speed and looks at the person standing on the platform. Describe the motion of the person standing on the platform with respect to the running passenger.
Answer:
Doppler effect
Explanation:
this means that at one point when the person running is close to the observer it will appear to run fast but slower as he moves away from the observer
A passenger is running inside a stationary train at some speed and looks at the person standing on the platform, then the person standing on the platform seems to be moving backward relative to the person running inside the stationary train because of the concept of relative velocity.
What is Velocity?The total displacement covered by any object per unit of time is known as velocity. It depends on the magnitude as well as the direction of the moving object.
A passenger is going inside a stationary train at a certain pace when they look at the person standing on the platform, and because of the idea of relative velocity,
The person on the platform appears to be moving backward in relation to the passenger moving inside the stationary train.
By observing from the side of the person standing on the platform the person running inside the stationary train would appear to move in the forward direction because of the relative velocity.
Learn more about Velocity from here
brainly.com/question/18084516
#SPJ2
A body at rest is given an initial uniform acceleration of 8m/s2 for 30s after which the acceleration is reduced to 5m/s2 for the next twenty seconds. The body maintains the speed attained for 60s, after which it is brought to rest in 20s.
Explanation:
v=u+at, where v,u,a and t are the final velocity, initial velocity, acceleration and time, respectively.
For t=0 s to t=30 s , a =8 m/s 2.
For t=30 s to t=50 s , a = 5 m/s 2.
For t=50 s to t=110 s , a = 0 m/s 2.
For t=110 s to t=130 s , a is such that the body comes to rest at the end of this period.
For t=0 s to t=30 s ,v=0+8t⇒v=8t m/s.
At t=30s,v=8×30=240 m/s.
For t=30 s to t=50 s ,v=240+5(t−30)⇒v=90+5t m/s
At t=50s,v=90+5×50=340 m/s.
For t=50 s to t=110 s ,v=340 m/s.
For t=110 s to t=130 s ,v=340+a(t−110).
The body comes to a halt at t=130 s ⇒0=340+a(130−110).
0=340+20a⇒a=−34020=−17 m/s2.
For t=110 s to t=130 s ,v=340−17(t−110)=2210−17t m/s.
A car accelerates from a standstill to 60 km/hr in 10.0 seconds. What is its acceleration?
The acceleration of the car is 1.66 m per sec square.
How to calculate acceleration?The rate at which an item changes its velocity is known as acceleration, a vector quantity. If an object's velocity is changing, it is accelerating.
Initial velocity=0
Final velocity= 60km/hr
To convert it into m/sec
1 km=1000 m
1 hr=3600 sec
So= (60×1000)÷3600=16.66 m/sec
time=10 sec
We know that acceleration is the rate of change of velocity per unit of time.
acceleration=(final velocity-initial velocity)÷ time taken
= (16.66-0)÷10
= 1.66 m per sec square
So, Acceleration will be, 1.66 m per sec square
For more details on acceleration refer to:
brainly.com/question/2437624
#SPJ10
Calculate magnetic field strength current 3a flows in wire 2.5m and produces a force 15n
The magnetic field strength willl be 2 T. A force known as the Lorentz force acts on the charge when it is subject to an electric and magnetic field.
What is Lorentz force?Lorentz force is defined as the force acting on point charge when it is moving in an electric and magnetic field.
The given data in the problem is ;
B is the magnetic field strength =? T.
Current, I =?
L is the length of the wire
The magnetic force is found as;
F= BIL
15 N = B × 3 A × 2.5 m
B = 2 T
Hence, the magnetic field strength willl be 2 T.
To learn more about the Lorentz force refer to the link;
https://brainly.com/question/13791875
#SPJ1
what evidence can you cite that the interstellar medium contains both gas and dust? (select all that apply.)
(a) The gas of interstellar medium can be detected from the radiations of photons of wavelength 21 cm.
(b) The gas of interstellar medium can be detected from the absorption lines present in the light from distant stars, which must be caused by a medium of density and temperature other than that of the stars emitting the lights.
What is interstellar medium?Interstellar medium is the matter and radiation that exist in the space between the star systems in a galaxy.
Evidence that interstellar medium contains both gas and dustThe gas of interstellar medium can be detected from the radiations of photons of wavelength 21 cm.The gas of interstellar medium can be detected from the absorption lines present in the light from distant stars, which must be caused by a medium of density and temperature other than that of the stars emitting the lights.Learn more about interstellar medium here: https://brainly.com/question/4173326
#SPJ11
a cyclist applies a constant forward force of 20 N to maintain a velocity 2.5 m/s. how much power does the cyclist deliver?
The power exerted by the cyclist is determined as 50 W.
Average power exerted by the cyclist
The power exerted by the cyclist is calculated as follows;
P = FV
where;
F is the applied forceV is velocityP = 20 x 2.5
P = 50 W
Thus, the power exerted by the cyclist is determined as 50 W.
Learn more about power here: https://brainly.com/question/25263760
#SPJ1
What is the change of state when magma crystallises to form igneous rock?
Answer:
liquid
Explanation:
due to high temperatures in the magma chamber all solids liquidify on reaching the surface with colder temperatures it now solidify to form igneous rock
HELP ME!!PLEASE ANSWER!!!!!!
How many states of matter are there? Describe each state, and give an example of each
Who is responsible of refraction light 1/3 in eye
The cornea is responsible of refraction light 1/3 in eye.
What is the function of the cornea?In addition to the protective function, it plays a fundamental role in the formation of vision. Transparent, it works like a lens over the iris, focusing light from the pupil towards the retina.
Normally, the cornea and lens deflect (refract) incoming light rays, focusing them on the retina. The shape of the cornea is fixed, but the lens changes shape to focus on objects at different distances from the eye.
See more about cornea at brainly.com/question/2297282
#SPJ12
