The normal force exerted on the crate by the elevator is 294 N. The normal force is the force exerted by a surface perpendicular to an object in contact with it.
In this case, the crate is in contact with the floor of the elevator. To solve the problem, we need to find the weight of the crate, which is given by its mass (60 kg) multiplied by the acceleration due to gravity (9.8 m/s2).
So the weight of the crate is 588 N. The force exerted on the crate by the elevator is the normal force.
According to Newton's second law, the sum of the forces acting on the crate is equal to its mass multiplied by its acceleration.
The crate is slowing down at 6 m/s2, so the net force on it is its weight minus the force exerted by the elevator.
Thus, the normal force is equal to the weight of the crate minus the net force acting on it, which is (60 kg)(9.8 m/s2) - (60 kg)(6 m/s2) = 294 N. Therefore, the normal force exerted on the crate by the elevator is 294 N.
To know more about Newton's second law, refer here:
https://brainly.com/question/13447525#
#SPJ11
The ultraviolet catastrophe is good evidence for the:
neither the wave nor the particle nature of quanta
wave nature of quanta
both particle and wave nature of quanta
particle nature of quanta
The ultraviolet catastrophe is good evidence for the (B).wave nature of quanta is correct option.
The ultraviolet catastrophe was a problem in classical physics that arose when attempting to explain the spectral distribution of blackbody radiation. According to classical physics, the energy of radiation should increase without limit as the frequency of the radiation increases. However, experiments showed that this was not the case, and there was a maximum frequency beyond which the energy decreased.
This problem was resolved by Max Planck in 1900, who proposed that energy is quantized and can only exist in discrete packets or "quanta". This led to the development of quantum mechanics, which describes the behavior of matter and energy at the atomic and subatomic level.
The wave-particle duality is a fundamental concept in quantum mechanics that describes the dual nature of particles, which can exhibit both wave-like and particle-like behavior depending on the experimental setup. However, the ultraviolet catastrophe is specifically related to the wave nature of quanta, as it was the wave-like behavior of energy that led to the resolution of the problem.
To know more about wave nature
https://brainly.com/question/27077956
#SPJ4
A small truck is moving at 20 m/s. A large truck, with twice the mass, is traveling at half the speed. How does the momentum of the larger truck compare to the smaller truck?
The momentum of an object is directly proportional to its mass and velocity. Therefore, the momentum of the larger truck can be calculated as follows:
Momentum of larger truck = (2 x mass of smaller truck) x (1/2 x velocity of smaller truck)
Momentum of larger truck = (2 x m) x (0.5 x 20)
Momentum of larger truck = m x 20
This shows that the momentum of the larger truck is equal to the momentum of the smaller truck, as the increased mass is balanced by the decreased velocity.
In other words, the momentum of an object depends on both its mass and velocity, and changes in one factor can be compensated by changes in the other factor to maintain the same momentum.
To know more about Momentum, refer here:
https://brainly.com/question/30677308#
#SPJ11
If the protons were not held together by the strong nuclear force, what would be their initial acceleration due to the electric force between them
Using Newton's second law, F = ma, and the known mass of a proton, 1.673 x [tex]10^{27}[/tex] kg, the initial acceleration of the protons would be approximately 1.38 x [tex]10^{1}[/tex] [tex]m/s^{2}[/tex].
If the protons were not held together by the strong nuclear force, they would experience an electric force due to their positive charges.
According to Coulomb's law, the electric force between two charges is proportional to the product of the charges and inversely proportional to the square of the distance between them.
Therefore, the initial acceleration of the protons would depend on their separation distance and the magnitude of their charges.
Assuming a separation distance of 1 angstrom ([tex]10^{-10}[/tex] m), the electric force between two protons with charges of 1.602 x [tex]10^{-19}[/tex] C would be approximately 2.31 x [tex]10^{-28}[/tex] N.
Using Newton's second law, F = ma, and the known mass of a proton, 1.673 x [tex]10^{-27}[/tex] kg, the initial acceleration of the protons would be approximately 1.38 x [tex]10^{1}[/tex] [tex]m/s^{2}[/tex].
To know more about Newton's second law, refer here:
https://brainly.com/question/13447525#
#SPJ11
Help me!
in your own words, describe how the marble-jar experiment explains newton's law of inertia.
The marble-jar experiment is a classic demonstration of Newton's Law of Inertia. The experiment consists of a jar filled with marbles and a card covering the jar's opening.
When the jar is inverted quickly, the card falls, and the marbles remain in place.
According to Newton's Law of Inertia, an object at rest will remain at rest, and an object in motion will continue to move in a straight line at a constant velocity unless acted upon by an external force.
In this experiment, the marbles' inertia keeps them in place when the jar is inverted, while the card falls due to the external force of gravity.
This experiment provides a simple and tangible way to understand Newton's Law of Inertia.
To know more about Law of Inertia, refer here:
https://brainly.com/question/1830739#
#SPJ11
Suppose the book-printing industry is competitive and begins in a long-run equilibrium. Then hi-tech printing company invents a new process that sharply reduces the cost of printing books.
The new process will cause the demand for book printing services to increase, and this will cause the price of book printing services to fall.
The long-run equilibrium will shift to a new equilibrium, where the new cost structure will be reflected in the price of book printing services. The new process will result in lower prices and higher demand for book printing services, leading to an increase in the number of firms in the book printing industry, as well as an increase in the size of the market.
The cost savings due to the new process will be passed on to consumers, resulting in lower prices for books. This will benefit both the book printing companies as well as the consumers.
Know more about equilibrium here
https://brainly.com/question/30807709#
#SPJ11
Which isotope of carbon has the strongest nuclear and electrostatic forces? Explain your reasoning
The electrostatic forces are the same for all isotopes of carbon, but carbon-14 has the strongest nuclear forces due to the additional neutrons in its nucleus.
All isotopes of carbon have the same number of protons in their nucleus, which determines the electrostatic forces between the positively charged protons and negatively charged electrons. Therefore, the electrostatic forces are the same for all isotopes of carbon.
The strength of nuclear forces depends on the number of protons and neutrons in the nucleus. Generally, the more protons and neutrons an isotope has, the stronger the nuclear forces.
Carbon has three naturally occurring isotopes: carbon-12, carbon-13, and carbon-14. Carbon-12 has 6 protons and 6 neutrons, carbon-13 has 6 protons and 7 neutrons, and carbon-14 has 6 protons and 8 neutrons.
Therefore, carbon-14 has the strongest nuclear forces because it has the most neutrons in its nucleus. However, it is important to note that the difference in nuclear forces between carbon-12 and carbon-14 is relatively small and not significant in most everyday situations.
In summary, the electrostatic forces are the same for all isotopes of carbon, but carbon-14 has the strongest nuclear forces due to the additional neutrons in its nucleus.
To know more about forces refer here:
https://brainly.com/question/26115859#
#SPJ11
What does a fission reaction require to be sustainable?.
A fission reaction requires three main components to be sustainable: a sufficient amount of fissile material, a moderator to control the reaction, and a method of removing heat generated during the reaction.
1. Fissile material: To sustain a fission reaction, there needs to be a sufficient amount of fissile material, such as uranium-235 or plutonium-239. These materials have nuclei that are more likely to split when struck by a neutron, releasing energy and more neutrons in the process.
The critical mass is the minimum amount of fissile material required to maintain a self-sustained chain reaction.
2. Moderator: A moderator is a substance that slows down the neutrons released during fission. This is crucial for sustaining the reaction, as slower neutrons are more likely to be captured by fissile material and induce further fission events. Common moderators include water, heavy water, and graphite.
3. Heat removal: During a fission reaction, a large amount of heat is generated due to the release of energy. In order to maintain a sustainable reaction, it's necessary to remove this heat, typically by transferring it to a coolant, such as water or gas.
The coolant circulates through the reactor core, absorbing heat, and then transfers the heat to a heat exchanger or directly to a steam generator for power production.
In summary, a sustainable fission reaction requires a sufficient amount of fissile material to maintain a chain reaction, a moderator to control the reaction by slowing down neutrons, and an effective method of removing heat generated during the reaction.
To know more about sustainable refer here
https://brainly.com/question/29355708#
#SPJ11
Suppose that you wanted to travel to the next closest star to earth. proxima
centauri is the closest star to our solar system at a distance of 4.3 light years.
knowing that the space shuttle's typical speed is 28,000km/hr. how long
would it take you to get there?
It is equivalent to approximately 60.5 million days, or 165,850 years. The distance to Proxima Centauri is 4.3 light-years, which is equivalent to 4.068 x [tex]10^{13}[/tex] km.
To calculate how long it would take to travel that distance at a speed of 28,000 km/hr, we can divide the distance by the speed: 4.068 x [tex]10^{13}[/tex] km ÷ 28,000 km/hr = 1.452 x [tex]10^{9}[/tex] hours
That is equivalent to approximately 60.5 million days, or 165,850 years.
Therefore, it is currently not possible to travel to Proxima Centauri with the technology available to us. We would need to develop much faster spacecraft and propulsion systems to make interstellar travel feasible.
To know more about Proxima Centauri, refer here:
https://brainly.com/question/21107590#
#SPJ11
a guitar string 61 cm long vibrates with a standing wave that has three antinodes. part a which harmonic is this?
This standing wave corresponds to the third harmonic. The fundamental frequency of a guitar string is determined by the length of the string, which in this case is 61 cm.
When a standing wave is produced on the string, the nodes (points where the wave has zero displacement) and antinodes (points of maximum displacement) can be counted to determine the harmonic number. In this case, the number of antinodes is 3, which corresponds to the third harmonic.
The fundamental frequency of the string is determined by the equation f = 1/2L√T/m, where L is the length of the string, T is the tension, and m is the mass per unit length of the string. The third harmonic frequency is three times the fundamental frequency, which is calculated by multiplying the fundamental frequency by 3. Therefore, the third harmonic frequency of the guitar string is three times the fundamental frequency.
In addition, the wavelength of the third harmonic is one-third of the wavelength of the fundamental frequency. This is because the wavelength of a wave is inversely proportional to its frequency. The wavelength of the third harmonic is one-third of the wavelength of the fundamental frequency, and the distance between the antinodes is one-third of the wavelength. Therefore, the standing wave with three antinodes corresponds to the third harmonic.
Know more about displacement here
https://brainly.com/question/11934397#
#SPJ11
Assuming a total mass of 80 kg (bicycle plus rider), what must be the cyclist's power output to climb the same hill at the same speed?
The cyclist's power output must be equal to 784 N x speed. To climb the same hill at the same speed, the cyclist's power output must be equal to the gravitational force acting on the system (bicycle plus rider) multiplied by the speed at which they are moving.
The gravitational force can be calculated using the formula F = mg, where m is the total mass of the system (80 kg) and g is the acceleration due to gravity (9.8 [tex]m/s^{2}[/tex]). Therefore, the gravitational force acting on the system is 784 N (80 kg x 9.8 [tex]m/s^{2}[/tex]).
Assuming that the speed at which they are moving is constant, the power output required by the cyclist can be calculated using the formula P = F x v, where P is power, F is force, and v is velocity (speed). Therefore, the cyclist's power output must be equal to 784 N x speed.
For example, if the speed is 5 m/s, then the power output required by the cyclist would be 3920 watts (784 N x 5 m/s). However, it's important to note that this is a theoretical calculation and in reality, the power output required may be different due to factors such as air resistance, friction, and the gradient of the hill.
To know more about gravitational force, refer here:
https://brainly.com/question/12528243#
#SPJ11
when light enters a material of higher index of refraction, its speed select one: a. first increases then decreases. b. increases. c. first decreases then increases. d. decreases.
When light enters a material of higher index of refraction, its speed decreases. Option D is correct.
This phenomenon is known as refraction and is a result of the change in the speed of light as it passes through a material with a different refractive index. The refractive index is a measure of how much a material can bend light, compared to the speed of light in a vacuum. When light passes from a medium with a lower refractive index, such as air or vacuum, to a medium with a higher refractive index, such as water or glass, it slows down and bends towards the normal line, an imaginary line perpendicular to the surface of the material.
The amount of refraction that occurs depends on the angle of incidence, or the angle at which the light strikes the surface, as well as the difference in refractive indices between the two materials. The change in speed and direction of the light as it passes through a material of higher refractive index can be described by Snell's law. Option D is correct.
To know more about the Refraction, here
https://brainly.com/question/23750645
#SPJ4
A proton moving eastward with a velocity of 5. 0 km/s enters a magnetic field of 0. 20 T pointing northward. What are the magnitude and direction of the force that the magnetic field exerts on the proton
The magnitude of the force that a magnetic field exerts on a charged particle is given by the equation:
F = qvB sin(theta)
where q is the charge of the particle, v is its velocity, B is the magnetic field strength, and theta is the angle between the velocity vector and the magnetic field vector.
In this case, the proton has a positive charge of +1.6 x 10^-19 C, and it is moving eastward with a velocity of 5.0 km/s. The magnetic field is pointing northward with a strength of 0.20 T.
The angle between the velocity vector and the magnetic field vector is 90 degrees, since the velocity is eastward and the magnetic field is northward.
Plugging these values into the equation, we get:
F = (1.6 x 10^-19 C)(5.0 x 10^3 m/s)(0.20 T) sin(90)
F = 1.6 x 10^-19 N
So the magnitude of the force that the magnetic field exerts on the proton is 1.6 x 10^-19 N.
The direction of the force can be determined using the right-hand rule. If you point your right thumb in the direction of the proton's velocity (eastward), and your fingers in the direction of the magnetic field (northward), then the direction of the force vector is perpendicular to both, pointing downward. Therefore, the direction of the force on the proton is southward.
A 2 ω resistor and a 8.0 mh inductor are used in an lr circuit. if the initial current in the circuit is 2.0 a when a switch is thrown that allows the current in the circuit to decay, at what time will the current be 1.0 a?
The initial current is 2A, resistance is 2Ω, and inductance is 0.008H. The time for current decay to 1A is found to be around 2.1ms using the natural logarithm.
The current in an LR circuit can be modeled by the equation:
[tex]I(t) = I0e^{(-Rt/L)}[/tex]
where I(t) is the current at time t, I0 is the initial current, R is the resistance, L is the inductance, and e is the mathematical constant e.
We are given that the initial current is 2.0 A, the resistance is 2 Ω, and the inductance is 8.0 mH (or 0.008 H). We want to find the time it takes for the current to decay to 1.0 A.
Substituting the given values into the equation, we get:
[tex]1.0 A = 2.0 A \times e^{(-2\Omega t/0.008H)}[/tex]
Simplifying, we can divide both sides by 2.0 A and take the natural logarithm of both sides:
[tex]ln(0.5) = -2\Omega t/0.008H[/tex]
Solving for t, we get:
[tex]t = -0.008H \times ln(0.5) / 2\Omega[/tex]
Plugging in the given values, we get:
[tex]t \approx 0.0021 s[/tex] or 2.1 ms
Therefore, it will take approximately 2.1 ms for the current to decay to 1.0 A.
In an LR circuit, the inductor resists changes in current, so when the switch is thrown and the current starts to decay, the inductor generates a back EMF that opposes the change in current. This causes the current to decay exponentially over time, as described by the above equation.
To know more about resistance refer here:
https://brainly.com/question/30155623#
#SPJ11
The maximum allowable resistance for an underwater cable is one hundredth of an ohm per
meter and the resistivity of copper is 1. 54 x 10-80m.
a) Calculate the smallest cross sectional area of copper cable that could be used.
The smallest cross-sectional area of the copper cable that could be used is approximately 1.54 x 10^-6 square meters.
To calculate the smallest cross-sectional area of the copper cable that could be used, we need to apply Ohm's law and the formula for resistivity.
Ohm's law states that resistance (R) equals resistivity (ρ) multiplied by the length (L) of the conductor, divided by the cross-sectional area (A). In this case, we have:
R = ρ * L / A
We are given the maximum allowable resistance (R) per meter, which is 0.01 ohms/meter, and the resistivity of copper (ρ) as 1.54 x 10^-8 ohm-meter. Since we're considering resistance per meter, the length (L) is 1 meter. We need to find the smallest cross-sectional area (A) that satisfies these conditions.
0.01 ohm = (1.54 x 10^-8 ohm-meter) * 1 meter / A
To find A, we can rearrange the formula:
A = (1.54 x 10^-8 ohm-meter) * 1 meter / 0.01 ohm
A ≈ 1.54 x 10^-6 square meters
So, the smallest cross-sectional area of the copper cable that could be used is approximately 1.54 x 10^-6 square meters.
To learn more about copper, refer below:
https://brainly.com/question/13677872
#SPJ11
Given that a 4 cylinder, 4 stroke engine gave the following test results:
Shaft Speed N = 2600 rev/min
Torque arm R = 16 cm
Net Brake Load F = 220 N
Fuel consumption mf = 2 g/s
Calorific Value (CV) = 42 MJ/kg
Determine the following:
(a) Brake Power;
(b) Fuel Power;
(c) Brake Thermal Efficiency.
By increasing and decreasing the brake thermal efficiency, compare the impact this has on the shaft speed or net brake load
(a) Pb = 2π * N * T
(b) Pf = mf * CV
(c) Brake Thermal Efficiency (ηb) = (Pb / Pf) * 100%
To determine the brake power, fuel power, and brake thermal efficiency, we can use the following formulas:
(a) Brake Power (Pb):
Pb = 2π * N * T
Where N is the shaft speed in revolutions per minute (rpm) and T is the torque.
(b) Fuel Power (Pf):
Pf = mf * CV
Where mf is the fuel consumption rate in kilograms per second and CV is the calorific value of the fuel in joules per kilogram.
(c) Brake Thermal Efficiency (ηb):
ηb = (Pb / Pf) * 100%
Let's calculate these values using the given information:
(a) Brake Power:
Shaft Speed N = 2600 rev/min
Torque arm R = 16 cm = 0.16 m
The torque (T) can be calculated using the formula:
T = F * R
Brake Power (Pb) = 2π * N * T
(b) Fuel Power:
Fuel consumption mf = 2 g/s = 0.002 kg/s
Calorific Value (CV) = 42 MJ/kg = 42 × [tex]10^6[/tex] J/kg
Fuel Power (Pf) = mf * CV
(c) Brake Thermal Efficiency:
Brake Thermal Efficiency (ηb) = (Pb / Pf) * 100%
Let's substitute the given values into the equations and calculate the results.
To know more about brake power refer here
https://brainly.com/question/31456389#
#SPJ11
a 193-v battery, an inductor, and a resistor are connected in series as shown in the diagram below. a two-way switch makes it possible to include or exclude the battery. the switch that had been in position 1 for a long time is suddenly moved to position 2. (enter your answers to at least two decimal places.) (a) what is the voltage across the resistor at the end of four time constants? 3.53 correct: your answer is correct. v (b) at this time, what is the voltage across the inductor? .107 incorrect: your answer is incorrect.
As for the Voltage across the inductor, it is equal to zero after four time constants because the current in the circuit has decreased to zero. Therefore, the correct answer for part (b) is zero, not 0.107.
When the switch is in position 1, the circuit is closed and the battery is connected in series with the inductor and resistor. This means that current flows through the circuit, causing a magnetic field to be generated by the inductor. However, when the switch is suddenly moved to position 2, the circuit is opened and the battery is no longer connected.
After the switch is moved, the current in the circuit begins to decrease due to the inductor's opposition to changes in current. The time it takes for the current to decrease to 36.8% of its original value is known as the time constant, which is calculated by dividing the inductance of the inductor by the resistance of the resistor.
After four time constants, the voltage across the resistor can be calculated using the equation V = V0 * e^(-t/RC), where V0 is the initial voltage, t is the time elapsed, R is the resistance, and C is the capacitance. Plugging in the values given, we get V = 193 * e^(-4/RC) = 3.53 volts.
As for the voltage across the inductor, it is equal to zero after four time constants because the current in the circuit has decreased to zero. Therefore, the correct answer for part (b) is zero, not 0.107.
To Learn More About Voltage
https://brainly.com/question/1176850
SPJ11
Horticulture (HURRY) 120 pts
Specialized technology works well in
, where the uniformity of the crop encourages tight-focused machines rather than unspecialized machines that can be adapted for multiple tasks
Horticulture is a field that greatly benefits from specialized technology. This is because the uniformity of crops in horticulture allows for machines that are tightly focused on specific tasks.
These machines are designed to perform specialized functions such as planting, pruning, and harvesting. This specialized equipment ensures that the crops are tended to with precision and care, which results in higher yields and better quality produce.
In contrast, unspecialized machines that can be adapted for multiple tasks may not perform as well in horticulture because they lack the precision and efficiency required for these specialized tasks.
So, in horticulture, specialized technology works well because it allows for precise and efficient handling of crops, which ultimately leads to better yields and higher-quality produce.
To learn more about horticulture, refer below:
https://brainly.com/question/28991945
#SPJ11
A length of copper wire was measured with a tape measure to give a length of 50. 0m with an uncertainty of 1 cm. The thickness of the wire was measured to be 1. 00mm,using a micrometer screw gauge. Calculate the volume of the copper used?
A copper wire was measured to be 50.0m long with an uncertainty of 1cm and had a thickness of 1.00mm measured with a micrometer screw gauge. The volume of copper used was [tex]3.93 \times 10^{-5}\; m^3[/tex] with an uncertainty of [tex]\pm 7.85 \times 10^{-9} m^3[/tex].
The volume of copper used can be calculated by multiplying the length, cross-sectional area, and density of copper. The length is given as 50.0 m with an uncertainty of [tex]\pm 0.01[/tex]m, and the thickness of the wire is given as 1.00 mm, which is equivalent to 0.001 m.
The cross-sectional area of the wire can be calculated using the formula for the area of a circle, which is πr², where r is the radius of the wire.
The radius of the wire can be calculated by dividing its thickness by 2, giving a value of 0.0005 m. Therefore, the cross-sectional area is [tex]\pi (0.0005)^2 = 7.85 \times 10^{-7} m^2[/tex]. The density of copper is 8.96 g/cm³, which is equivalent to [tex]8.96 \times 10^3 \;kg/m^3[/tex].
Using the formula V = L x A, where V is the volume of copper, L is the length of the wire, and A is the cross-sectional area, we get:
[tex]V = (50.0 \pm 0.01 m) \times (7.85 \times 10^{-7} m^2)[/tex]
[tex]V = 3.93 \times 10^{-5} m^3 \pm 7.85 \times 10^{-9} m^3[/tex]
To account for the uncertainties in the measurements, we used significant figures and error propagation rules. The uncertainty in the volume was calculated using the formula for the multiplication of quantities with uncertainties.
In summary, the volume of copper used was found to be [tex]3.93 \times 10^{-5}\; m^3[/tex] with an uncertainty of [tex]\pm 7.85 \times 10^{-9} m^3[/tex].
To know more about volume refer here:
https://brainly.com/question/30347304#
#SPJ11
A solenoid had 1040 turns and is 4.4 cm long. If it carries a current of 31 A, what is the magnetic field it creates?
Answer:
.92 T
Explanation:
This is just a plug-and-chug question.
Here is the formula: B = uni
u = vacuum permeability = 4pi * 10^-7 this is a given constant
n = turns per meter = 1040/ (4.4*10^-2)
i = current = 31 A also given by the problem
so B = .92 T
The unit of the magnetic field is Tesla ("T")
1. Using a block-and-tackle, a mechanic pulls 8. 2 m of chain with a force of 90 N in
order to lift a 320 N motor to a height of 2. 9 m.
a) What is the AMA( Actual mechanical advantage) 10 points
b) What is the IMA (Ideal Mechanical Advantage) 10 points
c. What is the efficiency of the block-and-tackle? (10 points)
The Actual Mechanical Advantage (AMA) is the ratio of the output force to the input force and can be calculated by dividing the output force (320 N) by the input force (90 N). This gives an AMA of 3.556.
What is force?Force is an external influence that causes an object to move, stop, accelerate, or change direction. It is expressed in a variety of ways, such as the push of a hand, the pull of gravity, or a blast of air. It can also be expressed in terms of energy, such as sound waves, radiation, or electrical current. Force is a vector quantity, meaning it has both magnitude and direction. This means that when two forces act on an object, the result is the sum of the forces acting in the same direction, and the difference of the forces acting in opposite directions.
a) The Actual Mechanical Advantage (AMA) is the ratio of the output force to the input force and can be calculated by dividing the output force (320 N) by the input force (90 N). This gives an AMA of 3.556.
b) The Ideal Mechanical Advantage (IMA) is the ratio of the output distance to the input distance and can be calculated by dividing the output distance (2.9 m) by the input distance (8.2 m). This gives an IMA of 0.353.
c) The efficiency of the block-and-tackle can be calculated by dividing the AMA by the IMA and multiplying by 100. This gives an efficiency of 100 x 3.556/0.353 = 1008.8%. This means that the block-and-tackle is able to convert 1008.8% of the input force into output force.
To learn more about force
https://brainly.com/question/12785175
#SPJ4
If I weigh 742. 32 N on Earth at a place where g = 9. 80 m/s2 and 5900. 91 N on the surface of another planet, what is the acceleration due to gravity on that planet?
The acceleration due to gravity on the surface of the other planet is approximately 77.98 m/s².
To find the acceleration due to gravity on another planet, we can use the formula:
Weight = Mass × Acceleration due to gravity
On Earth, your weight is given as 742.32 N, and the acceleration due to gravity is 9.80 m/s².
We can rearrange the formula to solve for mass:
Mass = Weight / Acceleration due to gravity
So, on Earth, your mass would be:
Mass on Earth = 742.32 N / 9.80 m/s²
Mass on Earth = 75.63 kg
Now, let's consider the surface of another planet where your weight is given as 5900.91 N.
We'll use the same formula and solve for the acceleration due to gravity on that planet:
5900.91 N = Mass × Acceleration due to gravity on the other planet
Substituting the value of mass we calculated earlier:
5900.91 N = 75.63 kg × Acceleration due to gravity on the other planet
Now, we can solve for the acceleration due to gravity on the other planet:
Acceleration due to gravity on the other planet = 5900.91 N / 75.63 kg
Acceleration due to gravity on the other planet ≈ 77.98 m/s²
To know more about acceleration refer here
https://brainly.com/question/9415862#
#SPJ11
3. Compute the force of a small car, weighing 2,205 pounds, traveling 60 mph, that crashes into a steel pole and comes to a stop in 0. 05 second? dont know what to do
A small car weighing 2,205 pounds and traveling at 60 mph crashes into a steel pole and stops in 0.05 seconds. The force of the impact is calculated to be -53,600 N.
To calculate the force of a car that crashes into a steel pole, we need to use the formula F = m*a, where F is the force, m is the mass, and a is the acceleration.
To find the acceleration, we can use the formula[tex]a = (v_f - v_i) / t[/tex], where [tex]v_f[/tex] is the final velocity, [tex]v_i[/tex] is the initial velocity, and t is the time it takes to stop.
First, we need to convert the weight of the car from pounds to mass in kilograms, which is 1000 kg. Then, we need to convert the speed from miles per hour to meters per second, which is 26.8 m/s.
Using the formula a = (0 - 26.8) / 0.05, we get an acceleration of -536 m/s². Finally, we can use the formula F = m*a to find the force, which is -53,600 N.
The negative sign indicates that the force is in the opposite direction of the car's motion, meaning the car experiences a deceleration force. The force is very high due to the short stopping time, which can cause severe damage to the car and its occupants.
In summary, the force of a car crashing into a steel pole and coming to a stop in 0.05 seconds can be calculated using the formula F = m*a. Converting the weight to mass and the speed to meters per second, we can find the acceleration and use it to calculate the force.
To know more about force refer here:
https://brainly.com/question/26115859#
#SPJ11
Vibration of an object about an equilibrium point is called simple harmonic motion when the restoring force is proportional to:.
Vibration of an object about an equilibrium point is called simple harmonic motion when the restoring force is proportional to the displacement from the equilibrium point and is directed towards the equilibrium point.
This is known as Hooke's Law, which states that the force exerted by a spring is directly proportional to the displacement of the spring from its equilibrium position.
Mathematically, this can be expressed as F = -kx, where F is the restoring force, x is the displacement from the equilibrium point, and k is the spring constant, a measure of the stiffness of the spring.
To know more about Hooke's Law refer here
https://brainly.com/question/29126957#
#SPJ11
You produce a wave by oscillating one end of the rope up and down 2.0 times a second .what is the frequency of this wave?
The frequency of the wave produced by oscillating one end of the rope up and down 2.0 times a second is also 2.0 Hz (Hertz).
Frequency is defined as the number of oscillations or cycles that a wave completes in one second. In this case, each oscillation of the rope creates one complete cycle of the wave.
Therefore, if the rope is oscillating 2.0 times per second, it is completing 2.0 cycles of the wave each second, which is equivalent to a frequency of 2.0 Hz.
To know more about oscillations, refer here:
https://brainly.com/question/31472633#
#SPJ11
A motorcyclist traveling due north at 50km/h. the wind appears to come from north west at 60km/h . what is the true velocity of the wind
The true velocity of the wind is approximately 43.10 km/h.
To find the true velocity of the wind when a motorcyclist is traveling due north at 50 km/h, and the wind appears to come from the northwest at 60 km/h, we can use vector addition.
Step 1: Break the wind's apparent velocity into its north and west components. Since the wind is coming from the northwest, the north and west components will be equal.
Using the Pythagorean theorem (a² + b² = c²) to find the components:
North component:
a = 60 * cos(45°)
= 60 * 0.707
= 42.43 km/h
West component:
b = 60 * sin(45°)
= 60 * 0.707
= 42.43 km/h
Step 2: Subtract the motorcyclist's northward velocity from the north component of the wind's apparent velocity:
True north component of the wind:
42.43 - 50 = -7.57 km/h (southward)
Step 3: Combine the true north and west components of the wind's velocity using the Pythagorean theorem:
True wind velocity = √((-7.57)² + (42.43)²)
= √(57.36 + 1800.06)
= √1857.42
≈ 43.10 km/h
The true velocity of the wind is approximately 43.10 km/h.
To know more about velocity refer here
brainly.com/question/17127206#
#SPJ11
10. A thin beam of laser light of wavelength 514 nm passes through a diffraction grating having 3952 lines/cm. The resulting pattern is viewed on a distant curved screen that can show all bright fringes up to and including ±90. 0° from the central spot. What is the TOTAL number of bright fringes that will show up on the screen? A) 4 B) 5 C) 8 D) 9 E) 10
The TOTAL number of bright fringes that will show up on the screen is B) 5.
To answer this question, we need to use the following terms: wavelength, diffraction grating, lines/cm, and bright fringes.
Step 1: Convert the given data into meters
Wavelength (λ) = 514 nm = 514 * 10^(-9) m
Lines per cm (n) = 3952 lines/cm = 3952 * 10^2 lines/m (since 1 cm = 0.01 m)
Step 2: Calculate the grating spacing (d)
d = 1 / n = 1 / (3952 * 10^2) m
Step 3: Calculate the maximum order (m) using the grating equation
sin(90°) = m * λ / d
Since sin(90°) = 1,
m = d / λ
Step 4: Plug in the values and solve for m
m = (1 / (3952 * 10^2)) / (514 * 10^(-9))
m ≈ 2.09
Since m must be an integer, the maximum order is m = 2.
Step 5: Count the total number of bright fringes
For each order, there are 2 bright fringes (one on each side of the central spot), and one central spot (m = 0). Thus, the total number of bright fringes is:
Total bright fringes = 2 * (number of orders) + 1
Total bright fringes = 2 * (2) + 1
Total bright fringes = 5
So, the correct answer is B) 5.
For more about bright fringes:
https://brainly.com/question/31591286
#SPJ11
Your teacher sets two cups on a bench at the front of the class. One contains water dyed blue and the other clear water. The teacher says one cup is very salty water while the other is fresh water. You must figure out which is which. How would you do this?
Tasting water to identify which cup contains salty water or fresh water may not be reliable, as taste can be subjective and some individuals may have a weaker sense of taste.
Another approach is to use a conductivity meter or a multimeter with conductivity measurement capabilities to test the water in each cup. Salty water has a higher conductivity than fresh water due to the presence of ions, so the cup with higher conductivity would contain the salty water.
A third approach is to use a refractometer to measure the refractive index of the water. Salty water has a higher refractive index than fresh water due to the presence of dissolved salts, so the cup with a higher refractive index would contain the salty water.
In summary, to determine which cup contains salty water and which contains fresh water, one can use taste, a conductivity meter, a multimeter with conductivity measurement capabilities, or a refractometer.
Each of these methods has its own advantages and disadvantages, and the choice of method depends on factors such as the resources available and the specific characteristics of the water being tested.
To know more about salty water refer here:
https://brainly.com/question/29362135?#
#SPJ11
in a football game wanting kicks off to the other at the moment the receiver catches the ball he is 40 m from the nearest Tucker the receiving runs left to right at a speed of 10 m/s the toddler runs right to left at a speed of 6 m/s
Answer: yes
Explanation: good luck
Calculate the weight of an object sitting on the Earth’s surface if the mass of the object is 50 kg? Assuming the force of gravity g = 9. 81 m/s²)
The weight of an object with a mass of 50 kg on Earth's surface is 490.5 N (Newtons).
To calculate the weight of an object on Earth's surface, we need to consider the mass of the object and the force of gravity (g). In this case, the mass is given as 50 kg, and the force of gravity is assumed to be 9.81 m/s².
Step-by-step explanation:
1. Start with the mass of the object (m) which is given as 50 kg.
2. Next, take the force of gravity (g) as 9.81 m/s² (as provided).
3. Now, we need to use the weight formula, which is:
Weight (W) = mass (m) × force of gravity (g)
4. Substitute the values of mass and force of gravity in the formula:
W = 50 kg × 9.81 m/s²
5. Perform the multiplication:
W = 490.5 N
So, the weight of the object sitting on Earth's surface with a mass of 50 kg is 490.5 Newtons.
Know more about force of gravity click here:
https://brainly.com/question/14874038
#SPJ11
Which surface would have more friction?
wooden
glass
paper
sandpaper
Out of the given options, sandpaper would have the highest friction.
Friction depends on two factors - surface roughness and surface area in contact also depends on Normal force. Sandpaper has a very rough, abrasive surface with lots of peaks and valleys. This greatly increases the surface area in contact and mechanical interlocking with any surface it touches. This results in high friction.The other options:• Wooden surface: Depends on the smoothness of the wood, can range from low to medium friction.
• Glass surface: Very smooth so it has low friction.
• Paper surface: Relatively smooth so friction would be low to medium depending on the paper type.
from lowest to highest friction it would be:Glass < Paper < Wooden < SandpaperSandpaper has the roughest surface, so it exhibits the highest friction among the given options.