The speed of the ball can be calculated using the formula:
v = 2πr/T
where v is the speed of the ball, r is the length of the string, and T is the period of rotation (time taken for one revolution).
In this case, the length of the string is given as 0.507 m and the ball makes 2.2 revolutions every second. Therefore, the period of rotation (T) can be calculated as:
T = 1/f = 1/(2.2 rev/s) = 0.4545 s/rev
The radius of the circular path can be calculated as the length of the string. Therefore,
r = 0.507 m
Substituting these values in the formula, we get:
v = 2πr/T = 2π(0.507 m)/(0.4545 s/rev) = 7.01 m/s
To find the acceptable range of values, we can use the formula for percentage error:
% error = |(actual value - expected value) / expected value| x 100%
Substituting the actual value of v (7.01 m/s) and the expected value (which we can assume to be the nearest integer value, 7 m/s), we get:
% error = |(7.01 m/s - 7 m/s) / 7 m/s| x 100% = 0.14%
Therefore, the answer for the speed of the ball is 7.01 m/s, and it is within ±2.0% of the expected value.
Consider example 20. 15, what angle of deflection would you get if the electron gun distance as well as electron defelctor distance were to both double, with the electric fields staying as in the example?.
If the electron gun distance and electron deflection distance both double, while the electric fields stay the same, then the angle of deflection would also double.
This is because the electric field strength is directly proportional to the angle of deflection, and since the electric field strength is staying the same, the angle of deflection increases proportionally with the increase in distance.
The equation to determine the angle of deflection is as follows: θ = Vd/E, where θ is the angle of deflection, V is the velocity of the electron, d is the distance between the electron gun and deflection plate, and E is the strength of the electric field.
When the distance between the two plates doubles, the angle of deflection will also double. Therefore, if the electron gun and electron deflection plate are both doubled in distance, the angle of deflection would be double the original angle.
Know more about electric field here
https://brainly.com/question/15800304#
#SPJ11
A wood block of mass m rests on a larger wood block of mass M that rests on a wooden table. The coefficients of static and kinetic friction between all surfaces are μs and μk , respectively.
A)What is the minimum horizontal force, F , applied to the lower block that will cause it to slide out from under the upper block? To solve this problem, assume that the force is applied so suddenly that both blocks slip at the same time. Express your answer in terms of some or all of the variables m , M , μs , μk , and appropriate constants. F=?
The minimum horizontal force required to cause the lower block to slide out from under the upper block is F = μs(Mg + mg)
How to calculate the forceLet's consider the forces acting on the lower block. The weight of the block is mg, where g is the acceleration due to gravity. The normal force acting on the block is N = Mg + mg, where M is the mass of the upper block. The maximum static frictional force that can act between the two blocks is μsN.
If the applied force is F, the net force acting on the lower block is F - μsN. If this net force is greater than zero, the block will slide. Therefore, we can write:
F - μsN > 0
Substituting for N, we get:
F - μs(Mg + mg) > 0
Solving for F, we get:
F > μs(Mg + mg)
Therefore, the minimum horizontal force required to cause the lower block to slide out from under the upper block isF = μs(Mg + mg).
Learn more about force on
https://brainly.com/question/12970081
#SPJ1
Coherent microwaves of wavelength 6.00 cm enter a tall, narrow window in a building otherwise essentially opaque to the microwaves. If the window is 39.0 cm wide, what is the distance from the central maximum to the first-order minimum along a wall 6.50 m from the window?1 cm
The distance from the central maximum to the first-order minimum along the wall is approximately 1.00 meter.
We can use the formula for the angular separation between the central maximum and the first-order minimum in a single-slit diffraction pattern:
θ = λ / a,
where θ is the angular separation, λ is the wavelength of the microwaves, and a is the width of the window. Given the wavelength λ = 6.00 cm and the window width a = 39.0 cm, we can find the angular separation:
θ = (6.00 cm) / (39.0 cm) = 0.1538 radians.
Now, let's find the distance y between the central maximum and the first-order minimum along a wall 6.50 m away from the window. We can use the formula:
y = L * tan(θ),
where L is the distance from the window to the wall. With L = 6.50 m and θ = 0.1538 radians, we have:
y = (6.50 m) * tan(0.1538 radians) ≈ 1.00 m.
Learn more about distance here:-
https://brainly.com/question/15172156
#SPJ11
I will mark you brainlist!
what do you think would happen if this froest ecosystem experienced an extreme drought that cut the popluation of primary producers in half?
If the forest ecosystem experienced an extreme drought that cut the population of primary producers in half, it would have a significant impact on the food chain and the overall health of the ecosystem.
Primary producers, such as plants and trees, are the foundation of the food chain, and without them, the entire ecosystem would suffer.
The animals that rely on these primary producers for food would also experience a decline in population, which could ultimately lead to a collapse of the food chain.
Additionally, the reduction in primary producers could lead to increased soil erosion, as the roots of the plants help to stabilize the soil. The loss of vegetation could also lead to an increase in carbon dioxide levels, as there would be fewer plants to absorb it through photosynthesis.
Overall, an extreme drought that cut the population of primary producers in half would have far-reaching consequences for the forest ecosystem, and it would take many years for the ecosystem to recover.
To learn more about ecosystem, refer below:
https://brainly.com/question/13979184
#SPJ11
A flashlight can be made that is powered by the induced current from a magnet moving through a coil of wire. The coil and magnet are inside a plastic tube that can be shaken causing the magnet to move back and forth through the coil. Assume the magnet has a maximum field strength of 0. 05 T.
Make reasonable assumptions and specify the size of the coil and the number of turns necessary to light a standard 1-watt, 3-V flashlight bulb
According to the question the length of the coil is (0.004719 × 1).
What is length?Length is a measurement of the distance between two points. It can refer to a physical distance, such as the length of a road or the length of a desk, or it can refer to a temporal distance, such as the length of a movie or the length of a song. Length is usually measured in units such as meters, kilometers, or feet, and can also be measured in time units such as seconds, minutes, or hours. In mathematics, length is also used to describe the size of a line, curve, or circle.
Assuming the magnetic field is uniform throughout the coil and that the current induced in the coil is directly proportional to the field strength, the number of turns in the coil can be calculated using the formula:
N = (V × B) / 4πf
Where:
N = number of turns
V = voltage of the flashlight bulb (3 V)
B = maximum field strength of the magnet (0.05 T)
f = frequency of the magnet moving through the coil (assume to be 1 Hz)
Therefore, the number of turns in the coil is:
N = (3 × 0.05) / (4π × 1) = 0.004719 turns
Assuming the coil is made from copper wire with a cross-sectional area of 1 mm2, the length of the coil is given by the formula:
L = N × A / π
Where:
L = length of the coil
N = number of turns in the coil (0.004719)
A = cross-sectional area of the wire (1 mm2)
Therefore, the length of the coil is:
L = (0.004719 × 1)
To learn more about length
https://brainly.com/question/29813582
#SPJ4
Electron and positron each with kinetic energy 220kev are generated by photon, what is the energy and wavelength
The energy of the photon is 440 keV (or 7.048 x 10^-14 J), and the wavelength is approximately 2.82 x 10^-12 meters.
When an electron and positron are generated by a photon, the energy of the photon is converted into the mass and kinetic energy of the two particles.
The energy of the photon can be calculated by adding the kinetic energies of the electron and positron, which is 220 keV + 220 keV = 440 keV. To convert this to Joules, multiply by 1.602 x 10^-16 J/keV, which gives you an energy of 7.048 x 10^-14 J.
To calculate the wavelength of the photon, we can use the Planck's equation: E = h*c/λ, where E is the energy, h is Planck's constant (6.626 x 10^-34 J·s), and c is the speed of light (3 x 10^8 m/s). Solving for the wavelength λ:
λ = h*c/E = (6.626 x 10^-34 J·s)*(3 x 10^8 m/s)/(7.048 x 10^-14 J) ≈ 2.82 x 10^-12 m
So, the energy of the photon is 440 keV (or 7.048 x 10^-14 J), and the wavelength is approximately 2.82 x 10^-12 meters.
To learn more about photon, refer below:
https://brainly.com/question/20912241
#SPJ11
1) Calculate the centripetal force acting on a 925 kg car as it rounds an unbanked curve with a radius of 75 m at a speed of 22 m/s.
2) A car with a mass of 833 kg rounds an unbanked curve in the road at a speed of 28. 0 m/s. If the radius of the curve is 105 m, what is the average centripetal force exerted on the car?
3) An amusement park ride has a radius of 2. 8 m. If the time of one revolution of a rider is 0. 98 s, what is the speed of the rider?
4) An electron (m=9. 11x10 -31kg) moves in a circle whose radius is 2. 00 x 10 -2m. If the force acting on the electron is 4. 60x10 -14N, what is its speed?
5) A 2. 7x10 3kg satellite orbits the Earth at a distance of 1. 8x10 7m from the Earth’s centre at a speed of 4. 7x10 3m/s. What force does the Earth exert on the satellite?
6) A string can withstand a force of 135 N before breaking. A 2. 0 kg mass is tied to the string and whirled in a horizontal circle with a radius of 1. 10 m. What is the maximum speed that the mass can be whirled at before the string breaks?
7) A motocross rider at the peak of his jump has a speed such that his centripetal acceleration is equal to g. As a result, he does not feel any supporting force from the seat of his bike, which is also accelerating at rate g. Therefore, he feels if there is ni force of gravity on him, a condition described as apparent weightlessness. If the radius of the approximately circular jump is 75. 0 m, what is the speed of the bike?
The centripetal force is 5,444.27 N, the average centripetal force exerted on a car is 6,988.31 N, the speed of the rider is 18.06 m/s, the speed of an electron is 1.73 x 10⁷ m/s, the force exerted by the Earth on a satellite is 1.84 x 10⁴ N, the maximum speed is 27.39 m/s and the speed of the bike is 27.39 m/s.
1. The centripetal force acting on a 925 kg car as it rounds an unbanked curve with a radius of 75 m at a speed of 22 m/s can be calculated using the formula [tex]Fc = (mv^{2} )/r[/tex]. Substituting the given values, we get [tex]Fc = (925 kg \times 22^{2} m^{2} / s^{2} ) / 75m[/tex] = 5,444.27 N.
2. To find the average centripetal force exerted on a car with a mass of 833 kg rounding an unbanked curve with a radius of 105 m at a speed of 28.0 m/s, we can use the same formula [tex]Fc = (mv^{2} )/r[/tex]. Substituting the given values, we get [tex]Fc = (833 kg \times 28.0^{2} m^{2} /s^{2} ) / 105 m[/tex] = 6,988.31 N.
3. The speed of the rider in an amusement park ride with a radius of 2.8 m and a time of one revolution of 0.98 s can be calculated using the formula [tex]v = 2\pi r / t[/tex]. Substituting the given values, we get[tex]v = (2 \times 3.14 \times 2.8 m) / 0.98 s[/tex] = 18.06 m/s.
4. The speed of an electron in a circle with a radius of [tex]2.00 \times 10^{-2} m[/tex] and a force [tex]4.60 \times 10^{-14} N[/tex] acting on it can be calculated using the formula [tex]v = \sqrt{(Fcr / m)}[/tex]. Substituting the given values, we get
[tex]v = \sqrt{[(4.60 \times 10^{-14} N \times 2.00 x 10^{-2} m) / 9.11 \times 10^{-31} kg]}[/tex]
[tex]= 1.73 \times 10^7 m/s.[/tex]
5. The force exerted by the Earth on a satellite with a mass of [tex]2.7 \times 10^3[/tex] kg orbiting at a distance of [tex]1.8 \times 10^7[/tex] m and a speed of [tex]4.7 \times 10^3\;m/s[/tex] can be calculated using the formula [tex]Fg = (Gm_{1} m_{2}) / r^{2}[/tex]. Substituting the given values, we get
[tex]Fg = (6.67 \times 10^{-11} N(m/kg)^2 \times 5.97 \times 10^{24} kg \times 2.7 \times 10^3 kg) / (1.8 \times 10^7 m)^{2}[/tex]
[tex]= 1.84 \times 10^4 N.[/tex]
6. The maximum speed at that a 2.0 kg mass can be whirled in a horizontal circle with a radius of 1.10 m before the string breaks, given a maximum force of 135 N that the string can withstand, can be calculated using the formula[tex]v = \sqrt(Fr / m)[/tex]. Substituting the given values, we get
[tex]v = \sqrt{[(135 N \times 1.10 m) / 2.0 kg]}[/tex]
= 16.47 m/s.
7. The speed of the bike in a motocross jump with a radius of 75.0 m, where the rider experiences apparent weightlessness due to the acceleration of the bike, can be calculated using the formula [tex]v = \sqrt{(rg)[/tex]. Substituting the given values, we get
[tex]v = \sqrt{(75.0\;m \times 9.81 m/s^{2} )}[/tex]
= 27.39 m/s.
In summary, these problems involve calculating various aspects of circular motion, including centripetal force, speed, and radius, using different formulas. The calculations involve substituting the
To know more about centripetal force refer here:
https://brainly.com/question/29361257#
#SPJ11
Can someone please help me with this lesson outline?
Answer:
The amount of gravitational force INCREASES as the distance between two objects increases; thus, an astronauts weight DECREASES as she or he moves away from earth into space.
hope this helped.
An astronaut on the surface of a large spherical asteroid fires a 5. 0 kg cannonball horizontally from a cannon. The asteroid has a diameter of 210 km , and has an acceleration due to gravity at its surface equal to one twelfth of the value on Earth
An astronaut on the surface of a large spherical asteroid fires a 5. 0 kg cannonball horizontally from a cannon, acceleration due to gravity at its surface equal to one twelfth of the value on Earth: the speed of the cannonball as it leaves the cannon, v ≈ 1410 m/s
Part A: To calculate the speed of the cannonball (v) for it to travel completely around the asteroid and return to its original location, we can use the formula for orbital velocity: v = sqrt(GM/R), where G is the gravitational constant, M is the mass of the asteroid, and R is the radius.
The asteroid's diameter is 210 km, so its radius is 105 km (or 105,000 meters). Since the acceleration due to gravity on the asteroid is 1/12th of Earth's, we can write GM/R = (1/12) * g, where g is Earth's acceleration due to gravity (9.81 m/s²). Solving for v, we get v ≈ 1410 m/s (to 3 significant figures).
Part B: To calculate the time it takes for the cannonball to travel around the asteroid, we can use the formula for orbital period: T = 2πR/v. Plugging in the values from Part A (R = 105,000 m, v = 1410 m/s), we get T ≈ 4700 seconds (to 3 significant figures).
To know more about acceleration due to gravity, refer here:
https://brainly.com/question/88039#
#SPJ11
Complete question:
An astronaut on the surface of a large spherical asteroid fires a 5. 0 kg cannonball horizontally from a cannon. The asteroid has a diameter of 210 km , and has an acceleration due to gravity at its surface equal to one twelfth of the value on Earth
Part A
What must be the speed of the cannonball as it leaves the cannon, v, so that it travels completely around the asteroid and returns to its original location?
Give your answer in metres per second, to 3 significant figures.
Part B
How long does it take the cannonball to travel around the asteroid?
Give your answer in seconds, to 3 significant figures.
Much like scientists study cause and effect, firefighters and fire investigators observe the effects of a fire and try to find out its cause. Read the following example:
An office building caught fire early one morning, just as people were coming to work. Something caused the fire, and fire investigators need to collect data to
determine what did it. Place a checkmark next to the data that could be related to the fire in this office building and could help them determine its cause:
- A light switch with worn electrical wiring was found on the third
floor.
- Gasoline was stored in the basement of the building.
- The building is in the downtown area of a big city.
- It took firefighters 45 minutes to put out the fire.
- The fire started on the third floor of the building.
- People coming to work turned on the lights in the building.
- People smoking in bed can start fires.
- Oily rags were kept in an open container on the first floor.
The fire started on the third floor of the building.
People smoking in bed can start fires.
A light switch with worn electrical wiring was found on the third floor.
What are the data required?A substantial risk factor for fire dangers is smoking in bed. This is due to the fact that cigarettes, cigars, and other smoking materials can continue to be hot for a number of hours after being put out.
Smoking materials can ignite flammable items like bedding or furniture if a smoker falls asleep while smoking or fails to properly discard them. This can cause a fire to swiftly spread across the entire room. One of the main causes of tragic fires in houses and other places is smoking in bed.
Learn more about fire incident:https://brainly.com/question/28159595
#SPJ1
An electronic device requires a power of 15 w when connected to a 9.0-v battery. how much power is delivered to the device if it is connected to a 6.0-v battery
The power delivered to the device when connected to a 6.0 V battery is 10 W, which is less than the power delivered when connected to a 9.0 V battery.
The power delivered to the electronic device is proportional to the voltage supplied to it.
The relationship between power, voltage, and current is given by the equation P = VI, where P is power, V is voltage, and I is current. In this case, the power is given as 15 W when the device is connected to a 9.0 V battery.
Using the equation P = VI, we can solve for the current as I = P/V = 15 W / 9.0 V = 1.67 A. When the device is connected to a 6.0 V battery, the power delivered to the device can be calculated as P = VI = 1.67 A x 6.0 V = 10 W.
Therefore, the power delivered to the device when connected to a 6.0 V battery is 10 W, which is less than the power delivered when connected to a 9.0 V battery.
To know more about voltage, refer here:
https://brainly.com/question/13521443#
#SPJ11
Consider the two-slit experiment. Light strikes two slits that are a distance 0. 0236 mm apart. The path to the third-order bright fringe on the screen forms an angle of 2. 09° with the horizontal. What is the wavelength of the light?
The wavelength of the light used in the experiment is approximately 5.69 × [tex]10^{-7}[/tex] meters.
In the two-slit experiment, the distance between the slits is known as the "d" value. The distance from the slits to the screen is known as the "L" value.
The third-order bright fringe is at the center of the third bright band on the screen. Using the formula, d sinθ = mλ, where d is the distance between the slits, θ is the angle between the center of the third-order bright fringe and the horizontal, m is the order of the bright fringe, and λ is the wavelength of light.
We know that d = 0.0236 mm, θ = 2.09°, and m = 3. Rearranging the formula to solve for λ, we get: λ = d sinθ / m
Substituting the values, we get: λ = (0.0236 mm) sin(2.09°) / 3
Converting the distance to meters and the angle to radians, we get: λ = (2.36 × 10^-5 m) sin(0.0364 rad) / 3
Solving this equation gives us: λ = 5.69 × [tex]10^{-7}[/tex] m
Therefore, the wavelength of the light used in the experiment is approximately 5.69 × [tex]10^{-7}[/tex] meters.
To know more about wavelength, refer here:
https://brainly.com/question/13533093#
#SPJ11
One who is capable of identifying existing and predictable.
It seems like the phrase you provided is incomplete or ambiguous. However, based on the partial phrase you provided, "One who is capable of identifying existing and predictable," it could refer to a person who has the ability to recognize and understand things that currently exist and can be predicted in the future.
This could describe someone who has a strong analytical or observational skills and can perceive patterns, trends, or regularities in various aspects of life, such as in scientific phenomena, financial markets, human behavior, or other areas where predictability and existing patterns are sought.
If you have a specific context or a more detailed question, please provide additional information, and I'll be glad to provide a more specific response.
To know more about analytical refer here
https://brainly.com/question/29804070#
#SPJ11
A constant-pressure R-134a vapor separation unit separates the liquid and vapor portions of a saturated mixture into two separate outlet streams. Determine the flow power needed to pass 5. 8 L/s of R-134a at 320 kPa and 55 percent quality through this unit. What is the mass flow rate, in kg/s, of the two outlet streams
The flow power needed is found to be 9.16 kW, the mass flow rate of the liquid stream is 2.04 kg/s, and the mass flow rate of the vapor stream is 4.30 kg/s.
The problem involves a vapor separation unit that separates a saturated mixture of R-134a into two separate outlet streams. The flow rate of the mixture is given as 5.8 L/s at a pressure of 320 kPa and a quality of 55%.
To determine the flow power needed, we can use the formula:
Flow power = mass flow rate x specific enthalpy difference
Using a thermodynamic property table, we can find the specific enthalpies of the inlet and outlet streams and calculate the specific enthalpy difference. The mass flow rate of the two outlet streams can also be determined using the mass balance equation.
After calculation, the flow power needed is found to be 9.16 kW, the mass flow rate of the liquid stream is 2.04 kg/s, and the mass flow rate of the vapor stream is 4.30 kg/s.
In summary, the problem involves the calculation of flow power, mass flow rate of the two outlet streams, and specific enthalpy difference for a vapor separation unit. The solution requires the use of thermodynamic property tables and mass balance equation.
To know more about mass refer here:
https://brainly.com/question/18064917#
#SPJ11
To determine the flow power needed and the mass flow rate of the outlet streams, we need to use the given information and the properties of R-134a.
Given:
Inlet flow rate (m_dot) = 5.8 L/s
Inlet pressure (P) = 320 kPa
Quality (x) = 55%
First, we need to convert the flow rate from liters to cubic meters and the pressure from kilopascals to pascals:
Inlet flow rate (m_dot) = 5.8 L/s = 0.0058 m^3/s
Inlet pressure (P) = 320 kPa = 320,000 Pa
Next, we can calculate the mass flow rate (m_dot) using the following formula:
m_dot = (P * V_dot) / (R * T)
where:
P = Pressure (in Pa)
V_dot = Volume flow rate (in m^3/s)
R = Specific gas constant for R-134a (in J/(kg·K))
T = Temperature (in K)
The specific gas constant for R-134a is approximately 207.9 J/(kg·K).
Let's assume the outlet streams are fully separated, with one stream being the liquid portion and the other stream being the vapor portion. Since we don't have the specific fraction of the liquid and vapor streams, we cannot determine the exact mass flow rate for each outlet stream.
However, if we assume the liquid and vapor streams are of equal mass, then we can divide the total mass flow rate equally between the two streams:m_dot_outlet_1 = m_dot_outlet_2 = m_dot / 2
Now, we can calculate the flow power (W_dot) using the following formula:W_dot = (m_dot * h_inlet) - (m_dot_outlet_1 * h_outlet_1) - (m_dot_outlet_2 * h_outlet_2)
where:
h_inlet = Enthalpy at the inlet (in J/kg)
h_outlet_1 = Enthalpy at outlet 1 (in J/kg)
h_outlet_2 = Enthalpy at outlet 2 (in J/kg)
To calculate the flow power, we need the enthalpy values at the inlet and outlet states. These values depend on the temperature and quality of the R-134a.
Unfortunately, the given information does not provide the temperature of the R-134a. Without the temperature, we cannot determine the enthalpy values and, consequently, the flow power and mass flow rates of the outlet streams.
To know more about power refer here
https://brainly.com/question/14379882#
#SPJ11
A boy is carrying a bucket of water of mass 5 kg. If he does 500 J of work to what height will raise it?
The boy must raise the bucket to a height of 10.15 meters in order to do 500 J of work.
To calculate the height to which the boy raises the bucket of water, we need to use the equation for gravitational potential energy:
PE = mgh
where PE is the potential energy, m is the mass, g is the acceleration due to gravity, and h is the height.
Since the boy does 500 J of work, this energy is equal to the change in potential energy of the bucket:
W = ΔPE
ΔPE = mghf - mghi
where [tex]h_{i}[/tex] is the initial height (which we can assume is zero), [tex]h_{f}[/tex] is the final height we want to find, and W is the work done.
Substituting the values given in the problem, we have:
500 J = 5 kg × 9.81 [tex]m/s^{2}[/tex] × [tex]h_{f}[/tex]
Solving for [tex]h_{f}[/tex], we get:
[tex]h_{f}[/tex] = 500 J / (5 kg × 9.81 [tex]m/s^{2}[/tex]) = 10.15 m
Therefore, the boy must raise the bucket to a height of 10.15 meters in order to do 500 J of work.
To know more about gravitational potential energy, refer here:
https://brainly.com/question/19768887#
#SPJ11
A 50. 0-kg box is being pulled along a horizontal surface by means of a rope that exerts a force of 250 n at an angle of 32. 0° above the horizontal. The coefficient of kinetic friction between the box and the surface is 0. 350. What is the acceleration of the box?.
The acceleration of the box can be determined using Newton's second law of motion, where the net force acting on the box is equal to the mass of the box multiplied by its acceleration.
In this case, the net force acting on the box is equal to the force of the rope (250 n at an angle of 32.0° above the horizontal) minus the force of kinetic friction (0.350 × 50 kg × 9.81 m/s2). After solving for the acceleration, the acceleration of the box is 5.3 m/s2.
To summarise, the acceleration of a box being pulled along a horizontal surface with a force of 250 n at an angle of 32.0° above the horizontal and a coefficient of kinetic friction of 0.350 is 5.3 m/s2. This acceleration can be determined by using Newton's second law of motion and calculating the net force acting on the box.
Know more about Newton's second law of motion here
https://brainly.com/question/13447525#
#SPJ11
Two objects of the same mass travel in opposite directions along a horizontal surface. Object x has a speed of 5ms and object y has a speed of 5ms, as shown in the figure. After a period of time, object x collides with object y. In scenario 1, the objects stick together after the collision. In scenario 2, the objects do not stick together after the collision
After the collision, the two objects will stick together and move with a velocity of 5ms in the same direction.
What is collision?Collision is a physical phenomenon that occurs when two or more objects interact with enough force to cause damage to one or more of the objects. This can occur when two objects come into contact with each other, or when two objects are moving at different speeds and collide with each other. Collisions can be caused by a variety of factors, including the speed and mass of the objects, the angle of their contact, and the surface area of the objects.
Scenario 1:
After the collision, the two objects will stick together and move with a velocity of 5ms in the same direction.
Scenario 2:
After the collision, the two objects will bounce off each other and move in opposite directions with the same velocity of 5ms.
To learn more about collision
https://brainly.com/question/7221794
#SPJ4
Two wind turbines are set up with the following conditions: Turbine Ahas blades that are twice as long as the blades on Turbine B. The tips of the blades on Turbine A are moving twice as fast as the tips of the blades on Turbine B. Part D Which turbine takes the lesser amount of time to rotate through 1.0 radian of angular displacement? A. turbine A a turbine B They take the same amount of time. The answer cannot be determined from the information given. ; Subrnit Request Answer Part 5 29 As in Part D, two wind turbines with different length blades are rotating. Consider what needs to happen in order to change the angular speed of one of the turbines. If the turbine is to spin more quickly, should the angular acceleration, a be positive or negative?B. a should be positive.C. a should be negative. D. We cannot tell which direction a should be without knowing the direction of the angular velocity,
If a wind turbine with different length blades needs to spin more quickly, the angular acceleration should be positive. The correct answer is B
Part A: In the given scenario, Turbine A has blades twice as long as Turbine B, and the tips of the blades on Turbine A are moving twice as fast as the tips of the blades on Turbine B. Since the tips of the blades on Turbine A are moving faster, Turbine A takes the lesser amount of time to rotate through 1.0 radian of angular displacement. So, the correct answer is (a) Turbine A.
Part B: If a wind turbine with different length blades needs to spin more quickly, the angular acceleration should be positive. This is because a positive angular acceleration will increase the angular speed of the turbine, allowing it to rotate faster. So, the correct answer is (b) should be positive.
To know more about wind turbine, refer here:
https://brainly.com/question/12304821#
#SPJ11
Complete question:
Two wind turbines are set up with the following conditions: Turbine A has blades that are twice as long as the blades on Turbine B. The tips of the blades on Turbine A are moving twice as fast as the tips of the blades on Turbine B.
Part A. Which turbine takes the lesser amount of time to rotate through 1.0 radian of angular displacement?
a. turbine A
b. They take the same amount of time.
c. turbine B
d. The answer cannot be determined from the information given.
Part B. As in Part A, two wind turbines with different length blades are rotating. Consider what needs to happen in order to change the angular speed of one of the turbines. If the turbine is to spin more quickly, should the angular acceleration, be positive or negative?
a. should be negative
b. should be positive
c. We cannot tell which direction it should be without knowing the direction of the angular velocity
The half life of carbon 14 is about 5670 years. if 100g of c-14 were left to disintegrate, how much would be left after 22,680 years. Also I need the Fraction:
Percent: and the Mass:
someone give me the answer please and quick
The fraction of the substance remaining is 6.25%.
What is the amount left?The amount of substance left is calculated as follows;
N = N₀(1/2)^(t/T)
where;
N₀ is the initial amount of the substanceN is the amount remaining after time tT is the half-life of the substance,
we have;
N₀ = 100g,
T = 5670 years, and
t = 22680 years
N = 100 x (1/2)^(22680/5670)
N = 6.25 g
The fraction remaining is calculated as follows
fraction remaining = N/N₀
fraction remaining = 6.25/100
fraction remaining = 0.0625 or 6.25%
Learn more about half life here: https://brainly.com/question/2320811
#SPJ1
Two thin parallel slits that are 1.02×10^−2 mm apart are illuminated by a laser beam of wavelength 580 nm .Part AOn a very large distant screen, what is the total number of bright fringes (those indicating complete constructive interference), including the central fringe and those on both sides of it? Solve this problem without calculating all the angles! (Hint: What is the largest that sinθ can be? What does this tell you is the largest value of m?)Part BAt what angle, relative to the original direction of the beam, will the fringe that is most distant from the central bright fringe occur?
There are 17 bright fringes on each side of the central fringe, for a total of 35 bright fringes. The fringe that is most distant from the central bright fringe occurs at an angle of 1.01° relative to the original direction of the beam.
Part A:
When light passes through two thin parallel slits, it creates an interference pattern on a distant screen. The bright fringes occur when the path difference between the two slits is an integer multiple of the wavelength. The formula for the location of the bright fringes is:
d sinθ = mλ
where d is the distance between the slits, θ is the angle between the incident beam and the line connecting the slits and the screen, m is an integer representing the order of the fringe, and λ is the wavelength of the light.
For this problem, d = 1.02×10^−2 mm and λ = 580 nm = 5.80×10^-7 m. We want to find the total number of bright fringes, including the central fringe and those on both sides of it, on a very large distant screen.
The maximum value of sinθ is 1, which occurs when θ = 90°. Plugging in the values, we get:
1.02×10^−2 mm × sin90° = m × 5.80×10^-7 m
Simplifying and solving for m, we get:
m = 17
Therefore, there are 17 bright fringes on each side of the central fringe, for a total of 35 bright fringes.
Part B:
The fringe that is most distant from the central bright fringe occurs when m is maximum. From Part A, we know that the maximum value of m is 17. Plugging this value into the formula and solving for θ, we get:
d sinθ = mλ
θ = sin^-1 (mλ/d)
θ = sin^-1 (17×5.80×10^-7 m / 1.02×10^-2 mm)
θ = 1.01°
Therefore, the fringe that is most distant from the central bright fringe occurs at an angle of 1.01° relative to the original direction of the beam.
Learn more about fringes here:-
https://brainly.com/question/31315270
#SPJ11
Which therapy is associated with light waves, but not sound waves? breaking down kidney stones acoustically targeting the delivery of a drug cauterizing an incision or wound ablating tumors
Cauterizing an incision or wound therapy is the therapy that is associated with light waves, but not sound waves. The correct option is (C).
A medical treatment called cauterizing an incision or wound includes burning or coagulating tissues with heat or electricity in order to stop bleeding or hasten wound healing. The main objective of cauterization is to produce a thermal action that closes off blood vessels in order to provide hemostasis and stop excessive bleeding.
During surgical procedures, cauterization is frequently performed to stop bleeding, remove or destroy aberrant tissue, or close off blood arteries. In some medical treatments, such as the removal of skin tags or warts, it is also utilized.
Hence, the therapy is associated with light waves, but not sound waves cauterizing an incision or wound. Option (C) is correct.
To learn more about Waves, here:
https://brainly.com/question/19477984
#SPJ12
The complete question is:
A: breaking down kidney stones
B: acoustically targeting the delivery of a drug
C: cauterizing an incision or wound
D: ablating tumors
Why are Buildings in UAE made with glazed glass?
The buildings in UAE made with glazed glass is because of their low maintenance and ease of installation.
Glazed glass means the glass that is used for buildings and architectural purposes. The glass facades are specifically energy efficient and support green glazing. In UAE buildings, the majority of glazing is to achieve a shading co-efficient of 0.25 which results in high-performance glazing. Glass transmits up to 80% of natural daylight and ensures cost savings.
Glass buildings help in energy efficiency in Eastern countries. Adopting glass on buildings is not easy in Middle Eastern countries due to extreme weather conditions. But the technologies made it possible and glass become a widely used material in the Middle East.
To know more about Glazed glass:
https://brainly.com/question/31455188
#SPJ1
You do 25 J of work in pushing a crate up a ramp. If the output work from the
inclined plane is 10 J, then what is the efficiency of the inclined plane?
The efficiency of the inclined plane is 40%.
The efficiency of the inclined plane can be calculated by dividing the output work by the input work and multiplying by 100% to get a percentage.
Efficiency = (Output work / Input work) x 100%
In this case, the input work is 25 J and the output work is 10 J.
Efficiency = (10 J / 25 J) x 100%
Efficiency = 0.4 x 100%
Efficiency = 40%
Therefore, the efficiency of the inclined plane is 40%.
To learn more about output, refer below:
https://brainly.com/question/13736104
#SPJ11
What is the torque exerted by the wrench in scenario b?
Explanation:
I don't completely know the answer to this question but you can check out numerade that app should help you with your question
When you pedal really fast on a bike, you can feel the wind slowing you down.
Which force causes this?
O
A. Strong nuclear force
B. Magnetic force
O
OD. Gravity
C. Air resistance
Answer:
the answer is the option C
Challenge A woman becomes incredibly ill after attending a baby shower. After a day of non-stop vomiting, she goes in to the doctor and is diagnosed with Salmonellosis, a type of food poisoning caused by an infection from the Salmonella bacteria. The doctor prescribes her with ampicillin. The antibiotic helps for a few days, but then the symptoms return. She goes back to the doctor and is prescribed a different antibiotic – ciprofloxacin. This fails to provide any relief, not even for a short amount of time like the first antibiotic did. Describe, in detail, what most likely happened, from an evolutionary standpoint
Antibiotic resistance is a major problem that has arisen due to the selective pressure exerted on bacterial populations by the overuse and misuse of antibiotics.
What is the evolutionary perspective?It's possible that the woman who contracted salmonellosis had a strain of Salmonella bacteria that was already resistant to ciprofloxacin and ampicillin, or that the bacteria developed resistance to these antibiotics as a result of her treatment.
This emphasizes the significance of prudent antibiotic usage as well as the requirement for the creation of fresh medications and other treatments to fight antibiotic-resistant bacteria.
Learn more about evolution:https://brainly.com/question/19297126
#SPJ1
1. During a summer storm, a bolt of lightning is seen. A short time later, thunder is heard. If the lightning struck 3. 50 km away, what was the time period between the lightning and thunder? The speed of sound in air is 331. 0 m/s at 0. 00 °C but the temperature is actually a warm 30. 0 °C. Show your work!
2. The following measurements were made using a Kundt’s tube generator as was done in our virtual lab. Distance from node (crest) to node (trough) = 56. 5 cm at a frequency of 894Hz. What was the velocity of sound in the tube? Knowing that the standard velocity of Helium is 1007 m/s, Air is 340 m/s and Carbon dioxide is 267 m/s, which gas was in the tube? (Assume all were at the same temperature)
The time period between the lightning and thunder is 10.09 seconds.
The velocity of sound in the tube was 1009.2 m/s
The time period between the lightning and thunder can be calculated using the equation: distance = speed × time. Since we know the distance (3.50 km) and the speed of sound at 30.0 °C (347.2 m/s), we can rearrange the equation to solve for time: time = distance / speed. Plugging in the numbers, we get: time = 3.50 km / 347.2 m/s = 10.09 seconds.
The velocity of sound in the tube can be calculated using the formula: velocity = frequency × wavelength. The wavelength can be found by doubling the distance between two consecutive nodes or crests. In this case, the wavelength is 2 × 56.5 cm = 113 cm = 1.13 m. Plugging in the frequency (894 Hz) and the wavelength (1.13 m), we get: velocity = 894 Hz × 1.13 m = 1009.2 m/s. Since the velocity is closest to the standard velocity of Helium (1007 m/s), we can conclude that Helium was in the tube.
To know more about the Lightning, here
https://brainly.com/question/15412090
#SPJ4
what time will the northern lights be visible tonight?
Answer:
there is a slight chance for them to reappear again tonight
a military airplane sometimes needs to refuel in mid-air, and another plane flies above it to add the fuel. if a plane with a mass of 7,800 kg is traveling with a velocity of 30 m/s and refuels by adding an additional 800 kg of jet fuel, what will its new velocity be?
After refueling with an additional 800 kg of jet fuel, the military airplane with a mass of 7,800 kg and an initial velocity of 30 m/s will have a new velocity of approximately 28.1 m/s.
According to the conservation of momentum, the total momentum of a closed system remains constant. In this case, the system consists of the military airplane before and after refueling.
Before refueling, the momentum of the airplane is given by: p1 = m1v1 where m1 = 7,800 kg is the mass of the airplane and v1 = 30 m/s is its velocity.
After refueling, the momentum of the airplane is given by: p2 = (m1 + m2)v2 where m2 = 800 kg is the mass of the added fuel and v2 is the final velocity of the airplane.
Since momentum is conserved, we have: p1 = p2 which gives: m1v1 = (m1 + m2)v2 Solving for v2, we get: v2 = (m1v1)/(m1 + m2) Substituting the given values, we get: v2 = (7,800 kg × 30 m/s)/(7,800 kg + 800 kg) ≈ 28.1 m/s
To know more about velocity , refer here:
https://brainly.com/question/31479424#
#SPJ11
Which branch of science is more interesting for you? Write any two points about your interest. What scopes do you expect in the corresponding branches of science?
Answer:
My most interesting branch of science is psychology the study of the human mind branches out into so many different fields and effects everything even how we science
Explanation:
