Answer:
t = 402 years
Explanation:
To find the number of year that electrons take in crossing the complete transmission line, you first calculate the drift speed of the electrons. Then, you use the following formula for the current in a wire:
[tex]I=nqv_dA[/tex] (1)
n: number of mobile charge carrier per volume = 8.50*10^28 e/m^3
q: charge of the electron = 1.6*10^-19 C
vd: drift velocity of electron in the metal = ?
A: cross sectional area of the wire = π r^2 = π (0.02m/2)^2 = 3.1415*10^-4 m^2
I: current in the wire = 1110 A
You solve the equation (1) for vd:
[tex]v_d=\frac{I}{nqA}=\frac{110A}{(8.50*10^{28}m^{-3})(1.6*10^{-19}C)(3.1415*10^{-4}m^2)}\\\\v_d=2.59*10^{-4}m/s[/tex]
Next, you calculate the time by using the information about the length of the line transmission:
[tex]x=v_dt\\\\x=330km=330000m\\\\t=\frac{x}{v_d}=\frac{330000m}{2.59*10^{-4}m/s}=1,270,184,865s\\\\1,270,184,865s*\frac{1\ year}{3,156,107}=402.45\ years[/tex]
hence, the electrons will take aproximately 402 years in crossing the line of transmission
student conducted an experiment and find the density of an ICEBERGE. A students than recorded the following readings. Mass 425 25 g Volume 405 15 mL What experimental value should be quoted for the density of the ICEBERG? Compare your answer with the density of water, which is 3 1.00 10 kg . Show any calculations necessary to justify your answer
Complete Question
The complete question is shown on the first uploaded image
Answer:
The experimental value of density is [tex]\rho = 1.05*10^{3} \ kg/m^3 \pm 101 \ kg/m^3[/tex]
Comparing it with the value of density of water ([tex]1.0*10^{3} \ kg/m^3[/tex]) we can see that the density of ice is greater
Explanation:
From the question we are told
The mass is [tex]M = (425 \pm 25) \ g =(0.425 \pm 0.025) \ kg[/tex]
The volume is [tex]V = (405 \pm 15 ) \ mL = (0.000405 \pm 1.5*10^{-5}) \ m^3[/tex]
The experimental value of density is mathematically evaluated as
[tex]\rho = \frac{M}{V}[/tex]
[tex]\rho = \frac{0.425}{0.000405}[/tex]
[tex]\rho = 1.05 *10^{3} \ kg/m^3[/tex]
The possible error in this experimental value of density is mathematically evaluated as
[tex]\frac{\Delta \rho}{\rho} = \frac{\Delta M}{M} +\frac{\Delta V}{V}[/tex]
substituting value
[tex]\frac{\Delta \rho}{1.05*10^{3}} = \frac{0.025}{0.425} +\frac{1.5*10^{-5}}{0.000405}[/tex]
[tex]\Delta \rho = 101 \ kgm^{-3}[/tex]
Thus the experimental value of density is
[tex]\rho = 1.05*10^{3} \ kg/m^3 \pm 101 \ kg/m^3[/tex]
what is the speed of light in quartz
Answer:
1.95 x 10^8 m/s.
Explanation:
Answer:
the answer is 1.95 x 10^8 m/s
Explanation:
A population _____ follows a period of
Answer:
a population increase
Explanation:
During the 20th century, the world population increased from 1.65 billion to 6 billion. In 1970, the world's population was half that of today. In less than 15 years, 47% of the population will live in areas already under heavy water stress. In Africa, between 75 and 250 million people will face growing shortages in 2020 due to climate change. The scarcity of some arid and semi-arid regions will have a decisive impact on migration.
The coefficient of kinetic friction between a suitcase and the floor is 0.272. You may want to review (Pages 196 - 203) . Part A If the suitcase has a mass of 80.0 kg , how far can it be pushed across the level floor with 660 J of work
Answer:
Explanation:
The work required to push will be equal to work done by friction . Let d be the displacement required .
force of friction = mg x μ where m is mass of the suitcase , μ be the coefficient of friction
work done by force of friction
mg x μ x d = 660
80 x 9.8 x .272 x d = 660
d = 3 .1 m .
1. (a) The battery on your car has a rating stated in ampere-minutes which permits you to
estimate the length of time a fully charged battery could deliver any particular current
before discharge. Approximately how much energy is stored by a 50 ampere-minute 12
volt battery?
Answer:
Energy is stored by a 50 ampere-minute 12
volt battery is approximately = 36,000 J = 36 kJ
Explanation:
Power in electrical circuits is given as
Power = IV
But power generally is defined as energy expended per unit time
Power = (Energy/time)
Energy = Power × Time
Energy = IV × Time
Energy = (I.t × V)
I.t = 50 Ampere-minute = 50 × 60 = 3000 Ampere-seconds
V = 12 V
Energy = 3,000 × 12 = 36,000 J = 36 kJ
Hope this Helps!!!
A projectile is launched on the Earth with a certain initial velocity and moves without air resistance. Another projectile is launched with the same initial velocity on the Moon, where the acceleration due to gravity is one-sixth as large. How does the maximum altitude of the projectile on the Moon compare with that of the projectile on the Earth?
With smaller gravitational forces and therefor less vertical acceleration, the projectile launched on the moon ... with the same initial speed and direction ...
-- climbs faster,
-- spends more time climbing,
-- reaches a higher peak,
-- falls slower,
-- spends more time falling, and
-- covers more horizontal distance
than the projectile launched on the Earth.
This is not because of air resistance. It would be true even if there were no air resistance on the Earth. It's entirely a gravity thing.
John heats 1 kg of soup from 25 °C to 70 °C for 15 minutes by a heater. How long does the same heater take to heat 1.5 kg of the same kind of soup from 20 °C to 80 °C? The energy output per unit time by the heater is constant.
Answer:
30 minutes
Explanation:
Energy per time is constant, so:
E₁ / t₁ = E₂ / t₂
m₁C₁ΔT₁ / t₁ = m₂C₂ΔT₂ / t₂
(1 kg) C (70°C − 25°C) / 15 min = (1.5 kg) C (80°C − 20°C) / t
(1 kg) (45°C) / 15 min = (1.5 kg) (60°C) / t
3/min = 90 / t
t = 30 min
a ballistic pendulum is used to measure the speed of high-speed projectiles. A 6 g bullet A is fired into a 1 kg wood block B suspended by a cord of length l =2.2m. The block then swings through a maximum angle of theta = 60. Determine (a) the initial speed of the bullet vo, (b) the impulse imparted by the bullet on the block, (c) the force on the cord immediately after the impact
Answer:
(a) v-bullet = 399.04 m/s
(b) I = 2.38 kg m/s
(c) T = 2.59 N
Explanation:
(a) To calculate the initial speed of the bullet, you first take into account that the kinetic energy of both wood block and bullet, just after the bullet impacts the block, is equal to the potential gravitational energy of block and bullet when the cord is at 60° respect to the vertical.
The potential energy is given by:
[tex]U=(M+m)gh[/tex] (1)
U: potential energy
M: mass of the wood block = 1 kg
m: mass of the bullet = 6g = 6.0*10^-3 kg
g: gravitational constant = 9.8m/s^2
h: distance to the ground
The distance to the ground is calculate d by using the information about the length of the cord and the degrees of the cord respect to the vertical:
[tex]h=l-lsin\theta\\\\h=2.2m-2,2m\ sin60\°=0.29m[/tex]
The potential energy is:
[tex]U=(1kg+6*10^{-3}kg)(9.8m/s^2)(0.29m)=2.85J[/tex]
Next, the potential energy is equal to kinetic energy of the block and the bullet at the beginning of its motion:
[tex]U=\frac{1}{2}(M+m)v^2\\\\v=\sqrt{2\frac{U}{M+m}}=\sqrt{2\frac{2.85J}{1kg+6*10^{-3}kg}}=2.38\frac{m}{s}[/tex]
Next, you use the momentum conservation law, in order to calculate the speed of the bullet before the impact:
[tex]Mv_1+mv_2=(M+m)v[/tex] (2)
v1: initial velocity of the wood block = 0m/s
v2: initial speed of the bullet
v: speed of bullet and block = 2.38m/s
You solve the equation (2) for v2:
[tex]M(0)+mv_2=(M+m)v[/tex]
[tex]v_2=\frac{M+m}{m}v=\frac{1kg+6*10^{-3}kg}{6*10^{-3}kg}(2.38m/s)\\\\v_2=399.04\frac{m}{s}[/tex]
The speed of the bullet before the impact with the wood block is 399.04 m/s
(b) The impulse is gibe by the change in the velocity of the block, multiplied by the mass of the block:
[tex]I=M\Delta v=M(v-v_1)=(1kg)(2.38m/s-0m/s)=2.38kg\frac{m}{s}[/tex]
The impulse is 2.38 kgm/s
(c) The force on the cord after the impact is equal to the centripetal force over the block and bullet. That is:
[tex]T=F_c=(M+m)\frac{v^2}{l}=(1.006kg)\frac{(2.38m/s)^2}{2.2m}=2.59N[/tex]
The force on the cord after the impact is 2.59N
Answer:
The initial speed of the bullet [tex]V_o = 777.97m/s[/tex]The force on the cord immediately after the impact = [tex]19.71N[/tex]Explanation:
Apply the law of conversion of energy
[tex]V_f = \sqrt{2gh}[/tex]
where,
h = height of which the bullet and block rise after impact
[tex]h = L - Lcos\theta\\\\h = 2.2 - (2.2*cos60)\\\\h = 1.1m[/tex]
Therefore,
[tex]V_f = \sqrt{2gh}\\\\V_f = \sqrt{2*9.8*1.1}\\\\V_f = 4.64m/s[/tex]
From conservation of momentum principle, [tex]m_Bv_B = 0[/tex]
[tex]m_ov_o + m_Bv_B = (m_b+m_B)V_f\\\\0.006V_o = (0.006+1)*4.64\\\\V_o = 777.97m/s[/tex]
C) The force in the cable is due to the centrfugal force of the system, which is due to the motion of the system is a curved path and weight of the system
[tex]F = \frac{m_b+m_B}{L}V_f^2 + (m_b+m_B)g\\\\F = \frac{0.006+1}{2.2}*4.64^2 + (0.006+1)9.81\\\\F = 19.71N[/tex]
For more information on this visit
https://brainly.com/question/17756498
What is the resistance of a circuit with a voltage of 10 V in a current of 5 A use almond law to create the resistance
Answer:
2Ω
Explanation:
Ohm's law:
V = IR
10 V = (5 A) R
R = 2 Ω
A conducting sphere contains positive charge distributed uniformly over its surface. Which statements about the potential due to this sphere are true? All potentials are measured relative to infinity
a. The potential at the center of the sphere is zero.
b.The potential is lowest, but not zero, at the center of the sphere.
c. The potential at the center of the sphere is the same as the potential at the surface.
d. The potential at the center is the same as the potential at infinity.
e. The potential at the surface is higher than the potential at the center.
Answer:
a. FALSE
b. FALSE
c. TRUTH
d. FALSE
e. FALSE
Explanation:
To determine which statements are truth or false you focus in the following formula, for the electric potential generated by a conducting sphere:
[tex]V=\frac{Q}{4\pi \epsilon_o R}[/tex] inside the sphere
[tex]V'=\frac{Q}{4\pi \epsilon_o r}[/tex] for r > R (outside the sphere)
R: radius of the sphere
ε0: dielectric permittivity of vacuum
Q: charge of the sphere
As you can notice, inside the sphere the potential is constant. Inside the sphere, the potential is the same. Outside the surface the potential decreases as 1/r, being r the distance to the center of the sphere.
Hence, you can conclude:
a. The potential at the center of the sphere is zero. FALSE
b.The potential is lowest, but not zero, at the center of the sphere. FALSE
c. The potential at the center of the sphere is the same as the potential at the surface. TRUTH
d. The potential at the center is the same as the potential at infinity. FALSE
e. The potential at the surface is higher than the potential at the center. FALSE
. A ball weighs 120g on the earth surface,
i) What is its mass on the surface of the moon? 1mk
Answer:
WEIGHT ON MOON IS 0.2004N
Explanation:
mass of the body=120g=[tex]\frac{120}{1000}[/tex]kg=0.12kg (we will convert g into kg)
gravity on moon=1.67m/s²( to find the mass of anybody on another we should know its gravity)
as we know that (from the formula of weight)
weight=mass×gravity
w=mg
w=0.12kg²×1.67m/s²
w=0.2004N
Observe: Air pressure is equal to the weight of a column of air on a particular location. Airpressure is measured in millibars (mb). Note how the air pressure changes as you move StationB towards the center of the high-pressure system.
A. What do you notice?
B. Why do you think this is called a high-pressure system?
Answer:
a) When moving towards a high pressure center the pressure values increase in the equipment
b) This area is called high prison since the weight of the atmosphere on top is maximum
Explanation:
A) A high atmospheric pressure system is an area where the pressure is increasing the maximum value is close to 107 Kpa, the other side as low pressure can have small values 85.5 kPa.
When moving towards a high pressure center the pressure values increase in the equipment
B) This area is called high prison since the weight of the atmosphere on top is maximum
in general they are areas of good weather
A scuba diver and her gear displace a volume of 68.5 L and have a total mass of 71.8 kg . Part A What is the buoyant force on the diver in sea water? FB = nothing N Request Answer Part B Will the diver sink or float?
Answer:
A) Fb = 671.3 N
B) The diver will sink.
Explanation:
A)
The buoyant force applied on an object by a fluid is given by the following formula:
Fb = Vρg
where,
Fb = Buoyant Force = ?
V = Volume of the water displaced by the object = 68.5 L = 0.0685 m³
ρ = Density of Water = 1000 kg/m³
g = 9.8 m/s²
Therefore,
Fb = (0.0685 m³)(1000 kg/m³)(9.8 m/s²)
Fb = 671.3 N
B)
Now, in order to find out whether the diver sinks or float, we need to find weight of the diver with gear.
W = mg = (71.8 kg)(9.8 m/s²)
W = 703.64 N
Since, W > Fb. Therefore, the downward force of weight will make the diver sink.
The diver will sink.
The density of atmosphere (measured in kilograms/meter3) on a certain planet is found to decrease as altitude increases (as measured from the planet's surface). What type of relationship exists between the altitude and the atmospheric density, and what would the atmospheric density be at an altitude of 1,291 kilometers?
A.
inverse plot, 0.45 kilograms/meter3
B.
inverse plot, 0.51 kilograms/meter3
C.
quadratic plot, 1.05 kilograms/meter3
D.
inverse plot, 1.23 kilograms/meter3
E.
inverse plot, 0.95 kilograms/meter3
' A ' looks like the best choice.
Answer:
B. inverse plot, 0.51 kilograms/meter3
Explanation:
The International Space Station is about 90 meters across and about 380 kilometers away. One night t appears to be the same angular size as Jupiter. Jupiter is 143,000 km in size. Use serxa to figure out how far away Jupiter is in AU Note: 1 AU= 1.5 x 10-km
a) 6.0 x 10 Au
b) 4.0 AU
c) 9.1 x 1010 AU
d) 4.0 x 10 AU
Complete Question
The complete question is shown on the first uploaded image
Answer:
The distance is [tex]r_2 = 4 \ AU[/tex]
Explanation:
From the question we are told that
The size of Jupiter is [tex]s_2 = 143,000 \ km[/tex]
The length of the International Space Station is [tex]r_1 = 380\ km[/tex]
The size of the International Space Station is [tex]s_1 = 90 \ m =0.09 \ km[/tex]
The angular size where the same one night and this angular size is mathematically represented as
[tex]\theta = \frac{s}{r}[/tex]
Since [tex]\theta[/tex] is constant
[tex]\frac{s_1}{r_1} = \frac{s_2}{r_2}[/tex]
substituting values
[tex]\frac{0.09}{380} = \frac{143000}{r_2}[/tex]
=> [tex]r_2 = 6.04 * 10^{9} \ km[/tex]
Now we are told to convert to AU and 1 AU [tex]= 1.5 * 10^8 \ km[/tex]
So
[tex]r_2 = \frac{6.04 * 10^8}{1.5*10^{8}}[/tex]
[tex]r_2 = 4 \ AU[/tex]
Find another example of separation that is used to extract a material made useful by humans. Describe the process of separation and what we use the separated component for. (4-6 sentences)
If anyone would answer this I’ll answer ur questions for return!
Please and thank you!
Answer:
Salt
Explanation:
Salt plays a crucial role in maintaining human health. It is the main source of sodium and chloride ions in the human diet. Sodium is essential for the nerve and muscle function and is involved in the regulation of fluids in the body. Sodium also plays a role in the body's control of blood pressure and volume. Salt is harvested by seawater or brine is fed into large ponds of water and is drawn out through natural evaporation which allows the salt to be subsequently harvested.
Have a good day and stay safe!
In an RC-circuit, a resistance of R=1.0 "Giga Ohms" is connected to an air-filled circular-parallel-plate capacitor of diameter 12.0 mm with a separation distance of 1.0 mm. What is the time constant of the system?
Answer:
[tex]\tau = 1\ ms[/tex]
Explanation:
First we need to find the capacitance of the capacitor.
The capacitance is given by:
[tex]C = \epsilon_0 * area / distance[/tex]
Where [tex]\epsilon_0[/tex] is the air permittivity, which is approximately 8.85 * 10^(-12)
The radius is 12/2 = 6 mm = 0.006 m, so the area of the capacitor is:
[tex]Area = \pi * radius^{2}\\Area = \pi * 0.006^2\\Area = 113.1 * 10^{-6}\ m^2[/tex]
So the capacitance is:
[tex]C = \frac{8.85 * 10^{-12} * 113.1 * 10^{-6}}{0.001}[/tex]
[tex]C = 10^{-12}\ F = 1\ pF[/tex]
The time constant of a rc-circuit is given by:
[tex]\tau = RC[/tex]
So we have that:
[tex]\tau = 10^{9} * 10^{-12} = 10^{-3}\ s = 1\ ms[/tex]
A uniform disk with a 25 cm radius swings without friction about a nail through the rim. If it is released from rest from a position with the center level with the nail, then what is its angular velocity as it swings through the point where the center is below the na
Answer:
Explanation:
During the swing , the center of mass will go down due to which disc will lose potential energy which will be converted into rotational kinetic energy
mgh = 1/2 I ω² where m is mass of the disc , h is height by which c.m goes down which will be equal to radius of disc , I is moment of inertia of disc about the nail at rim , ω is angular velocity .
mgr = 1/2 x ( 1/2 m r²+ mr²) x ω²
gr = 1/2 x 1/2 r² x ω² + 1/2r² x ω²
g = 1 / 4 x ω² r + 1 / 2 x ω² r
g = 3 x ω² r/ 4
ω² = 4g /3 r
= 4 x 9.8 / 3 x .25
= 52.26
ω = 7.23 rad / s .
A particle leaves the origin with a speed of 3.6 106 m/s at 34 degrees to the positive x axis. It moves in a uniform electric field directed along positive y axis. Find Ey such that the particle will cross the x axis at x
Answer:
E = -4556.18 N/m
Explanation:
Given data
u = 3.6×10^6 m/sec
angle = 34°
distance x = 1.5 cm = 1.5×10^-2 m (This data has been assumed not given in
Question)
from the projectile motion the horizontal distance traveled by electron is
x = u×cosA×t
⇒t = x/(u×cos A)
We also know that force in an electric field is given as
F = qE
q= charge , E= strength of electric field
By newton 2nd law of motion
ma = qE
⇒a = qE/m
Also, y = u×sinA×t - 0.5×a×t^2
⇒y = u×sinA×t - 0.5×(qE/m)×t^2
if y = 0 then
⇒t = 2mu×sinA/(qE) = x/(u×cosA)
Also, E = 2mu^2×sinA×cosA/(x×q)
Now plugging the values we get
E = 2×9.1×10^{-31}×3.6^2×10^{12}×(sin34°)×(cos34°)/(1.5×10^{-2}×(-1.6)×10^{-19})
E = -4556.18 N/m
The value of Ey such that the particle will cross the x axis at x=1.5 cm is -4556.18 N/m.
What is electric field?The field developed when a charge is moved. In this field, a charge experiences an electrostatic force of attraction or repulsion depending on the nature of charge.
Given is a particle leaves the origin with a speed of 3.6 x 10⁶ m/s at 34 degrees to the positive x axis. It moves in a uniform electric field directed along positive y axis.
The distance x = 1.5 cm = 1.5×10⁻² m (assumed, not given in question)
The horizontal distance traveled by particle is
x = ucosθt
t = x/ucosθ
The force in an electric field is F = qE...................(1)
where, q is charge , E is the strength of electric field
From, newton 2nd law of motion, Force F = ma.................(2)
Equating both the equations, we get
ma = qE
a = qE/m..................(3)
The vertical distance, y =usinθt - 1/2at²
From equation 3, we have
y = usinθt - 1/2 (qE/m) t²
if y = 0, t = 2musinθ/(qE) = x / (ucosθ)
The electric field is represented as
Also, E = 2mu²×sinθ×cosθ/(xq)
Plug the values, we get
E = 2×(9.1×10⁻³¹)×(3.6 x 10⁶)²×sin34°×cos34°/( 1.5×10⁻² ×(-1.6)×10⁻¹⁹)
E = -4556.18 N/m
Thus, the electric field of the particle is -4556.18 N/m.
Learn more about electric field.
https://brainly.com/question/15800304
#SPJ5
Potential difference is measured in which units?
volts
amps
currents
watts
Answer:
Potential difference is measured in volts
Explanation:
The standard metric unit on electric potential difference is the volt, abbreviated V and named in honor of Alessandro Volta. One Volt is equivalent to one Joule per Coulomb.
Answer:
Your answer is A.) volts
Explanation:
A sound level of 96 dB is how many times as intense as one of 90 dB?
Answer:
A sound level of 96 dB is 4 times as intense as one of 90 dB
Explanation:
The formula of the intensity level of sound in decibels is given as follows:
Intensity Level = 10 log₁₀(I/I₀)
where,
I = Intensity of Sound
I₀ = Reference Intensity Level = 10⁻¹² W/m²
Therefore, for 96 dB sound level:
96 = 10 log₁₀(I₁/10⁻¹²)
log₁₀(I₁/10⁻¹²) = 96/10
I₁/10⁻¹² = 10^9.6
I₁ = (10⁻¹²)(4 x 10⁹)
I₁ = 0.004 W/m²
For 90 dB sound level:
90 = 10 log₁₀(I₂/10⁻¹²)
log₁₀(I₂/10⁻¹²) = 90/10
I₂/10⁻¹² = 10^9
I₂ = (10⁻¹²)(10⁹)
I₂ = 0.001 W/m²
Therefore,
I₁/I₂ = 0.004/0.001
I₁ = 4 I₂
Hence, the sound level of 96 dB is 4 times as intense as one of 90 dB.
In order to determine the coefficients of friction between rubber and various surfaces, a student uses a rubber eraser and an incline. In one experiment, the eraser begins to slip down the incline when the angle of inclination is 35.6° and then moves down the incline with constant speed when the angle is reduced to 30.8°. From these data, determine the coefficients of static and kinetic friction for this experiment.
Answer:
The coefficients of static and kinetic friction for this experiment are 0.716 and 0.596, respectively.
Explanation:
The Free Body Diagram associated with the experiment is presented as attachment included below.
Friction is a contact force that occurs as a reaction against any change in state of motion, which is fostered by gravity.
Normal force is another contact force that appears as a reaction to the component of weight perpendicular to the direction of motion. Let consider a framework of reference consisting in two orthogonal axes, one being parallel to the direction of motion (x-axis) and the other one normal to it (y-axis). Equations of motion are described herein:
[tex]\Sigma F_{x} = W \cdot \sin \theta - f = 0[/tex]
[tex]\Sigma F_{y} = N - W \cdot \cos \theta = 0[/tex]
Where:
[tex]W[/tex] - Weight of the eraser, measured in newtons.
[tex]f[/tex] - Friction force, measured in newtons.
[tex]N[/tex] - Normal force, measured in newtons.
[tex]\theta[/tex] - Angle of the incline, measured in degrees.
The maximum allowable static friction force is:
[tex]f = \mu_{s} \cdot N[/tex]
Where:
[tex]\mu_{s}[/tex] - Coefficient of static friction, dimensionless.
[tex]N[/tex] - Normal force, measured in newtons.
Likewise, the kinetic friction force is described by the following model:
[tex]f = \mu_{k} \cdot N[/tex]
Where:
[tex]\mu_{k}[/tex] - Coefficient of static friction, dimensionless.
[tex]N[/tex] - Normal force, measured in newtons.
And weight is equal to the product of the mass of eraser and gravitational constant ([tex]g = 9.807\,\frac{m}{s^{2}}[/tex])
In this exercise, coefficients of static and kinetic friction must be determined. First equation of equilibrium has to be expanded and coefficient of friction cleared:
[tex]m\cdot g \cdot \sin \theta - \mu\cdot N = 0[/tex]
[tex]\mu = \frac{m\cdot g \cdot \sin \theta}{N}[/tex]
But [tex]N = m\cdot g \cos \theta[/tex], so that:
[tex]\mu = \tan \theta[/tex]
Now, coefficients of static and kinetic friction are, respectively:
[tex]\mu_{s} = \tan 35.6^{\circ}[/tex]
[tex]\mu_{s} \approx 0.716[/tex]
[tex]\mu_{k} \approx \tan 30.8^{\circ}[/tex]
[tex]\mu_{k} \approx 0.596[/tex]
The coefficients of static and kinetic friction for this experiment are 0.716 and 0.596, respectively.
Which factor caused higher oil prices to directly lead to inflation?
It increased demand for cars, leading to higher automobile prices.
Companies passed on production and transportation costs to consumers.
The government began to print more money.
Gas prices declined too quickly, leading to oversupply
Answer: B, Companies passed on production and transportation costs to consumers
Explanation:
A higher oil price occurred when companies passed on production and transportation costs to consumers.
Cause of high price of oilThe oil producing companies spend so much money in producing crude oil from the reservoirs to the surface. They also spend money in processing and transporting the crude oil to the end users or consumers.
The final price of the oil depends on the total amount spent by these companies in producing the hydrocarbons.
Thus, a higher oil price occurred when companies passed on production and transportation costs to consumers.
Learn more about inflations here: https://brainly.com/question/1082634
6. When a positive charge is released and moves along an electric field line, it moves to a position of A) lower potential and lower potential energy. B) lower potential and higher potential energy. C) higher potential and lower potential energy. D) higher potential and higher potential energy.
Answer:
Since you would have to do work on the charge to bring it back to its original position, the charge moves to a position of lower potential and lower potential energy.
The positive charge is released from a point such that it will move along an uniform electric field to the position of lower potential and lower potential energy. Therefore, option (A) is correct,
When a positive charge (say +Q) is released from a point (say A) and moves in an uniform electric field to reach the point (say B), then some work is done on the charge. This work done is given as,
[tex]W=+Q(V_{A}-V_{B})[/tex]
Here, [tex]V_{A}[/tex] and [tex]V_{B}[/tex] are the potential differences between the points A and B respectively..
This means the charge is moving from higher potential to lower potential. And since it is moving along the uniform electric field, therefore the electric potential energy of charged system is decreased.
Thus, we conclude that on releasing the positive charge from a point, it starts moving along the electric field towards the direction of lower electric potential and lower electric potential energy. Hence, option (A) is correct.
Learn more about electric potential and electric potential energy here:
https://brainly.com/question/12645463?referrer=searchResults
A student drives 105.0 mi with an average speed of 61.0 mi/h for exactly 1 hour and 30
minutes for the first part of the trip. What is the distance in miles traveled during this
time?
Answer:
91.5 miles
Explanation:
61 miles per hour so 61(x amount of hours)
so 61 x 1.5 hours is 91.5 miles
A certain metal with work function of Φ = 1.7 eV is illuminated in vacuum by 1.4 x 10-6 W of light with a wavelength of λ = 600 nm. 1)How many photons per second, N, are incident on the metal? N = photons per second Submit 2)What is KEmax, the maximum kinetic energy of the electron that is emitted from the metal? KEmax = eV
Answer:
1) n = 4.47*10^12 photons
2) K = 0.25 eV
Explanation:
This is a problem about the photoelectric effect.
1) In order to calculate the number of photons that impact the metal, you take into account the power of the light, which is given by:
[tex]P=\frac{E}{t}=1.4*10^{-6}\frac{J}{s}[/tex] (1)
Furthermore you calculate the energy of a photon with a wavelength of 600nm, by using the following formula:
[tex]E_p=h\frac{c}{\lambda}[/tex] (2)
c: speed of light = 3*10^8 m/s
h: Planck's constant = 6.626*10^-34 Js
λ: wavelength = 600*10^-9 m
You replace the values of the parameters in the equation (2):
[tex]E_p=(6.626*10^{-34}Js)\frac{3*10^8m/s}{600*10^{-9}m}=3.131*10^{-19}J[/tex]
Next, you calculate the quotient between the power of the light (equation (1)) and the energy of the photon:
[tex]n=\frac{P}{E_p}=\frac{1.4*10^{-6}J/s}{3.131*10^{-19}J}=4.47*10^{12}photons[/tex]
The number of photons is 4.47*10^12
2) The kinetic energy of the electrons emitted by the metal is given by the following formula:
[tex]K=E_p-\Phi[/tex] (3)
Ep: energy of the photons
Φ: work function of the metal = 1.7 eV
You first convert the energy of the photons to eV:
[tex]E_p=3.131*10^{-19}J*\frac{6.242*10^{18}eV}{1J}=1.954eV[/tex]
You replace in the equation (3):
[tex]K=1.95eV-1.7eV=0.25eV[/tex]
The kinetic energy of the electrons emitted by the metal is 0.25 eV
(1). The Number of photons per second is,[tex]4.23*10^{12}[/tex]
(2). The maximum kinetic energy of the electron is 0.37eV.
(1). The power of light is given as,
[tex]P=1.4*10^{-6}W[/tex]
Energy is given as,
[tex]E=\frac{hc}{\lambda} =\frac{6.626*10^{-34}*3*10^{8} }{600*10^{-9} } \\\\E=3.313*10^{-19} Joule\\\\E=\frac{3.313*10^{-19}}{1.6*10^{-19} }=2.07eV[/tex]
Number of photons per second is,
[tex]N=\frac{P}{E}=\frac{1.4*10^{-6} }{3.313*10^{-19} } =4.23*10^{12}[/tex]
(2). the maximum kinetic energy of the electron is,
[tex]K.E=E-\phi[/tex]
Where [tex]\phi[/tex] is work function.
[tex]K.E=2.07-1.7=0.37eV[/tex]
Learn more:
https://brainly.com/question/12337396
A person is swimming in a river with a current that has speed vR with respect to the shore. The swimmer first swims downstream (i.e. in the direction of the current) at a constant speed, vS, with respect to the water. The swimmer travels a distance D in a time tOut. The swimmer then changes direction to swim upstream (i.e. against the direction of the current) at a constant speed, vS, with respect to the water and returns to her original starting point (located a distance D from her turn-around point) in a time tIn. What is tOut in terms of vR, vS, and D, as needed?
Answer:
The time taken is [tex]t_{out} = \frac{D}{v__{R}} + v__{S}}}[/tex]
Explanation:
From the question we are told that
The speed of the current is [tex]v__{R}}[/tex]
The speed of the swimmer in direction of current is [tex]v__{S}}[/tex]
The distance traveled by the swimmer is [tex]D[/tex]
The time taken to travel this distance is [tex]t_{out}[/tex]
The speed of the swimmer against direction of current is [tex]v__{s}}[/tex]
The resultant speed for downstream current is
[tex]V_{r} = v__{S}} +v__{R}}[/tex]
The time taken can be mathematically represented as
[tex]t_{out} = \frac{D}{V_{r}}[/tex]
[tex]t_{out} = \frac{D}{v__{R}} + v__{S}}}[/tex]
physics I need help :(
A student is given a small object that is hanging from a ring stand on a nylon thread. The student attempts to charge the object electrically in several ways. Based upon his results, he concludes the object is made of an insulating material. Which set of results must he have collected?
A. The object could be charged only by contact.
B. The object could be charged by either contact or induction.
C. The object could be charged by either contact or polarization.
D. The object could be charged only by polarization.
Answer:(a)
Explanation:
Student must have known that insulators can only be charged when they are rubbed against each other. In this process, one becomes electrically negative while other becomes electrically positive such that both have the same magnitude. The one which gains electrons becomes electrically negative due to the transfer of electrons while others lose the electron becomes positive due to the transfer of an electron to another body.
Astrophysicist Neil deGrasse Tyson steps into an elevator on the 29th floor of a skyscraper. For some odd reason, there is a scale on the floor of the elevator. Neil, whose mass is about 115 kg, decides to step on the scale and presses the button for a lower floor. The elevator starts traveling downwards with a constant acceleration of 1.5 m/s2 for 6.0 seconds, and then travels at a constant velocity for 6.0 seconds. Finally, the elevator has an upward acceleration of 1.5 m/s2 for 6.0 seconds as it comes to a stop.
A. If each floor is approximately 4 m tall, which floor does the elevator stop at?
B. If the mass of the elevator is 1,200 kg, what is the maximum tension of the elevator cable?
Answer:
A. Final Floor = 15.5 = 15 (Considering downward portion of elevator)
B. T = 14859.5 N = 14.89 KN
Explanation:
A.
First we calculate distance covered by the elevator during downward motion. Downward motion consists of two parts. First one is uniformly accelerated. For that part we use 2nd equation of motion:
s₁ = Vi t + (0.5)at²
where,
s₁ = distance covered during accelerated downward motion = ?
Vi = initial speed = 0 m/s (since elevator is initially at rest)
t = time taken = 6 s
a = acceleration = 1.5 m/s²
Therefore,
s₁ = (0 m/s)(6 s) + (0.5)(1.5 m/s²)(6 s)²
s₁ = 4.5 m
also we find the final velocity using 1st equation of motion:
Vf = Vi + at
Vf = 0 m/s + (1.5 m/s²)(6 s)
Vf = 9 m/s
Now, the second part of downward motion is with constant velocity. So:
s₂ = vt
where,
s₂ = distance covered during constant speed downward motion = ?
v = Vf = 9 m/s
t = 6 s
Therefore,
s₂ = (9 m/s)(6 s)
s₂ = 54 m
Now for distance covered during upward motion is given by the 2nd equation of motion. Since the values of acceleration and time are same. Therefore, it will be equal in magnitude to s₁:
s₃ = s₁ = 4.5 m
Therefore, the total distance covered by elevator is given by following equation:
s = s₁ + s₂ - s₃ (Downward motion taken positive)
s = 4.5 m + 54 m - 4.5 m
s = 54 m
Therefore, net motion of the elevator was 54 m downwards.
So the final floor will be:
Final Floor = Initial Floor - Distance Covered/Length of a floor
Final Floor = 29 - 54 m/4m
Final Floor = 15.5 = 15 (Considering the downward portion or floor of elevator)
B.
The maximum tension will occur during the upward accelerated motion. It is given by the formula:
T = m(g + a)
where,
T = Max. Tension in Cable = ?
m = total mass of person and elevator = 115 kg + 1200 kg = 1315 kg
g = 9.8 m/s²
a = acceleration = 1.5 m/s²
Therefore,
T = (1315 kg)(9.8 m/s² + 1.5 m/s²)
T = 14859.5 N = 14.89 KN
