A 1. 0-kg wheel in the form of a solid disk rolls along a horizontal surface with a speed of 6. 0 m/s. What is the total kinetic energy of the wheel

1. The law of conservation of momentum and the law of action-reaction. 2. The law of inertia. 3. The law of action-reaction. 4. The law of action-reaction. 5. The law of inertia.

1. A car runs into a fence, and the fence dents the car.
This demonstrates Newton's Third Law of Motion, which states that for every action, there is an equal and opposite reaction. As the car hits the fence, the fence exerts an equal force back on the car, causing the dent.

2. Karen drops a marble on the ground, and it rolls across the floor in a straight line.
This example illustrates Newton's First Law of Motion, also known as the Law of Inertia. It states that an object at rest stays at rest, and an object in motion stays in motion with the same speed and direction unless acted upon by an unbalanced force. In this case, the marble keeps rolling in a straight line due to its inertia.

3. Matthew lets go of a recently blown up balloon, and it flies across the room as the air escapes.
This is an example of Newton's Third Law of Motion. As the air escapes from the balloon, it exerts a force in one direction. The balloon experiences an equal and opposite force, causing it to fly across the room.

4. Pushing your baby brother on the swing makes him go higher.
This situation demonstrates Newton's Second Law of Motion, which states that the acceleration of an object is directly proportional to the net force acting on it and inversely proportional to its mass (F = ma). When you push the swing, you are applying a force that causes it to accelerate, making it go higher.

5. You place a pencil on your desk, and it stays there.
This example represents Newton's First Law of Motion (the Law of Inertia) again. The pencil remains at rest on the desk because there is no unbalanced force acting upon it.

For more about conservation:

https://brainly.com/question/30333660

#SPJ11

The efficiency of the inclined plane is 40%.

The efficiency of the inclined plane can be calculated by dividing the output work by the input work and multiplying by 100% to get a percentage.

Efficiency = (Output work / Input work) x 100%

In this case, the input work is 25 J and the output work is 10 J.

Efficiency = (10 J / 25 J) x 100%
Efficiency = 0.4 x 100%
Efficiency = 40%

Therefore, the efficiency of the inclined plane is 40%.

To learn more about output, refer below:

https://brainly.com/question/13736104

#SPJ11

The power delivered to the device when connected to a 6.0 V battery is 10 W, which is less than the power delivered when connected to a 9.0 V battery.

The power delivered to the electronic device is proportional to the voltage supplied to it.

The relationship between power, voltage, and current is given by the equation P = VI, where P is power, V is voltage, and I is current. In this case, the power is given as 15 W when the device is connected to a 9.0 V battery.

Using the equation P = VI, we can solve for the current as I = P/V = 15 W / 9.0 V = 1.67 A. When the device is connected to a 6.0 V battery, the power delivered to the device can be calculated as P = VI = 1.67 A x 6.0 V = 10 W.

Therefore, the power delivered to the device when connected to a 6.0 V battery is 10 W, which is less than the power delivered when connected to a 9.0 V battery.

To know more about voltage, refer here:

https://brainly.com/question/13521443#

#SPJ11

When energy leaves the sun's core, it travels through the radiative zone in the form of c. electromagnetic waves.

This is also called as radiative energy. The radiative zone is the second zone of the sun, and it is the region where the energy created by nuclear reactions in the core is transferred through the Sun's outer layers. In this zone, the energy moves in the form of photons, which are particles of light that carry the energy.

The radiative zone is characterized by the high temperature and density of its materials, which cause the photons to scatter frequently before they can escape the zone. The photons that make it through the radiative zone eventually reach the convective zone, where they transfer their energy to the gas particles that rise and fall in the Sun's atmosphere through convection currents. These currents help distribute the energy from the core to the outer layers of the Sun and eventually to space.

In summary, the correct answer to the question is c. electromagnetic waves, which travel through the radiative zone as particles of light or photons.

Learn more about electromagnetic waves at: https://brainly.com/question/11820725

#SPJ11

The initial speed of the ball is approximately 22.0 m/s.

We can solve this problem using the kinematic equations of motion.

The initial velocity of the ball can be broken down into horizontal and vertical components. The horizontal component will remain constant throughout the flight, while the vertical component will be affected by gravity. We can use the following equations:

Horizontal motion:

x = v_x*t

Vertical motion:

y = v_y*t - (1/2)gt²

where:

We can solve for t by setting y = 0 (since the ball lands on the ground):

0 = v_y*t - (1/2)gt²

Solving for t, we get:

t = (2*v_y)/g

Now we can use the horizontal motion equation to solve for v_x:

x = v_xt

v_x = x/t

v_x = xg/(2*v_y)

Substituting the given values, we get:

v_x = (40.8 m)(9.81 m/s^2)/(2sin(42.0°)*cos(42.0°))

v_x ≈ 22.0 m/s

Learn more about initial speed here: https://brainly.com/question/24493758

#SPJ1

The acceleration of the box can be determined using Newton's second law of motion, where the net force acting on the box is equal to the mass of the box multiplied by its acceleration.

In this case, the net force acting on the box is equal to the force of the rope (250 n at an angle of 32.0° above the horizontal) minus the force of kinetic friction (0.350 × 50 kg × 9.81 m/s2). After solving for the acceleration, the acceleration of the box is 5.3 m/s2.

To summarise, the acceleration of a box being pulled along a horizontal surface with a force of 250 n at an angle of 32.0° above the horizontal and a coefficient of kinetic friction of 0.350 is 5.3 m/s2. This acceleration can be determined by using Newton's second law of motion and calculating the net force acting on the box.

Know more about  Newton's second law of motion here

https://brainly.com/question/13447525#

#SPJ11

The wavelength of the light used in the experiment is approximately 5.69 × [tex]10^{-7}[/tex] meters.

In the two-slit experiment, the distance between the slits is known as the "d" value. The distance from the slits to the screen is known as the "L" value.

The third-order bright fringe is at the center of the third bright band on the screen. Using the formula, d sinθ = mλ, where d is the distance between the slits, θ is the angle between the center of the third-order bright fringe and the horizontal, m is the order of the bright fringe, and λ is the wavelength of light.

We know that d = 0.0236 mm, θ = 2.09°, and m = 3. Rearranging the formula to solve for λ, we get: λ = d sinθ / m

Substituting the values, we get: λ = (0.0236 mm) sin(2.09°) / 3

Converting the distance to meters and the angle to radians, we get: λ = (2.36 × 10^-5 m) sin(0.0364 rad) / 3

Solving this equation gives us: λ = 5.69 × [tex]10^{-7}[/tex] m

Therefore, the wavelength of the light used in the experiment is approximately 5.69 × [tex]10^{-7}[/tex] meters.

To know more about wavelength, refer here:

https://brainly.com/question/13533093#

#SPJ11

(i). The flow speed in the smaller section is 11 m/s.

(ii).  The pressure in the smaller section is 7,352.56 Pa.

To solve this problem, we can apply the principle of conservation of mass and the Bernoulli's equation, which relates the pressure, velocity, and height of a fluid in a steady flow.

Given:

Density of the liquid (ρ) = 1.65 g/cm³ = 1650 kg/m³ (since 1 g/cm³ = 1000 kg/m³)

First section:

Cross-sectional area (A1) = 10 cm² = 0.001 m²

Flow speed (v1) = 275 cm/s = 2.75 m/s

Pressure (P1) = 1.20 ×[tex]10^5[/tex] Pa

Second section:

Cross-sectional area (A2) = 2.50 cm² = 0.00025 m²

(i) To find the flow speed in the smaller section (v2), we can use the principle of conservation of mass:

A1v1 = A2v2

Solving for v2:

v2 = (A1v1) / A2

v2 = (0.001 m² × 2.75 m/s) / 0.00025 m²

v2 = 11 m/s

(ii) To find the pressure in the smaller section (P2), we can use Bernoulli's equation:

P1 + (1/2)ρv1² + ρgh1 = P2 + (1/2)ρv2² + ρgh2

Since the two sections are horizontal, the heights (h1 and h2) are the same, so the terms ρgh1 and ρgh2 cancel out. Additionally, the liquid is assumed to be at the same height, so we can disregard the gravitational term.

Simplifying the equation:

P1 + (1/2)ρv1² = P2 + (1/2)ρv2²

Solving for P2:

P2 = P1 + (1/2)ρv1² - (1/2)ρv2²

P2 = 1.20 × [tex]10^5[/tex] Pa + (1/2) × 1650 kg/m³ × (2.75 m/s)² - (1/2) × 1650 kg/m³ × (11 m/s)²

P2 = 1.20 × [tex]10^5[/tex] Pa + 9526.56 Pa - 45675 Pa

P2 = 7,352.56 Pa

To know more about Bernoulli's equation refer here

https://brainly.com/question/29865910#

#SPJ11

Stored elastic potential energy can be utilized in everyday objects such as springs and rubber bands, allowing for the transfer of energy through the conversion of potential energy into kinetic energy.

One common example of stored elastic potential energy being utilized is a compressed spring. When a spring is compressed, work is done on it to store potential energy, which can then be released to do work on other objects. For instance, a spring-loaded toy car will store potential energy in its compressed spring, which is then released when the car is let go, causing it to move forward. This energy transfer is from the spring to the car's kinetic energy.

Another example of stored elastic potential energy is a stretched rubber band. When a rubber band is stretched, energy is stored in its molecular bonds, which can be released when the band is allowed to snap back into its original shape. This potential energy can be utilized in everyday life, for example, in a slingshot. When the rubber band is stretched back in a slingshot, it stores potential energy, which is then released when the projectile is released, converting potential energy into kinetic energy. This energy transfer is from the rubber band to the projectile's kinetic energy.

In both cases, the transfer of energy occurs through the conversion of potential energy into kinetic energy, allowing for work to be done on another object. These examples show how the principle of stored elastic potential energy can be utilized in everyday objects, making them more efficient and useful.

To learn more about potential energy

https://brainly.com/question/24284560

#SPJ4

The cable should have a diameter of approximately 0.092 cm or an order of magnitude of one centimeter.

To determine the diameter of the cable needed to support a tension of 20.0 kN, we can use the principle of cross-sectional area. The maximum tension that a wire can withstand is proportional to its cross-sectional area. Therefore, to support a tension that is 83.33 times greater than the maximum tension of a single wire, the cross-sectional area of the cable must also be 83.33 times greater.

The cross-sectional area of a wire is given by the formula A = πr², where A is the cross-sectional area, and r is the radius of the wire. Since the diameter of the wire is given as 1.00 mm, the radius is 0.50 mm or 0.005 cm. Therefore, the cross-sectional area of a single wire is:

A₁ = π(0.005 cm)² = 0.00007854 cm²

To find the diameter of the cable, we can use the formula for the cross-sectional area of a circle:

A₂ = πr₂²

where A₂ is the cross-sectional area of the cable and r₂ is the radius of the cable.

We know that the cross-sectional area of the cable needs to be 83.33 times greater than the cross-sectional area of a single wire:

A₂ = 83.33 A₁ = 83.33 x 0.00007854 cm² = 0.00654 cm²

Substituting this value into the formula for the cross-sectional area of a circle:

πr₂² = 0.00654 cm²

r₂² = 0.00654/π

r₂ = √(0.00654/π) = 0.046 cm

Therefore, the radius of the cable is 0.046 cm, and the diameter is twice that:

d = 2r₂ = 0.092 cm or 0.92 mm (to two significant figures)

In conclusion, the cable should have a diameter of the order of magnitude of one centimeter (0.092 cm).

To learn more about tension

https://brainly.com/question/30033702

#SPJ4

The buildings in UAE made with glazed glass is because of their low maintenance and ease of installation.

Glazed glass means the glass that is used for buildings and architectural purposes. The glass facades are specifically energy efficient and support green glazing. In UAE buildings, the majority of glazing is to achieve a shading co-efficient of 0.25 which results in high-performance glazing. Glass transmits up to 80% of natural daylight and ensures cost savings.

Glass buildings help in energy efficiency in Eastern countries. Adopting glass on buildings is not easy in Middle Eastern countries due to extreme weather conditions. But the technologies made it possible and glass become a widely used material in the Middle East.

To know more about Glazed glass:

https://brainly.com/question/31455188

#SPJ1

It seems like the phrase you provided is incomplete or ambiguous. However, based on the partial phrase you provided, "One who is capable of identifying existing and predictable," it could refer to a person who has the ability to recognize and understand things that currently exist and can be predicted in the future.

This could describe someone who has a strong analytical or observational skills and can perceive patterns, trends, or regularities in various aspects of life, such as in scientific phenomena, financial markets, human behavior, or other areas where predictability and existing patterns are sought.

If you have a specific context or a more detailed question, please provide additional information, and I'll be glad to provide a more specific response.

To know more about analytical refer here

https://brainly.com/question/29804070#

#SPJ11

The flow power needed is found to be 9.16 kW, the mass flow rate of the liquid stream is 2.04 kg/s, and the mass flow rate of the vapor stream is 4.30 kg/s.

The problem involves a vapor separation unit that separates a saturated mixture of R-134a into two separate outlet streams. The flow rate of the mixture is given as 5.8 L/s at a pressure of 320 kPa and a quality of 55%.

To determine the flow power needed, we can use the formula:

Flow power = mass flow rate x specific enthalpy difference

Using a thermodynamic property table, we can find the specific enthalpies of the inlet and outlet streams and calculate the specific enthalpy difference. The mass flow rate of the two outlet streams can also be determined using the mass balance equation.

After calculation, the flow power needed is found to be 9.16 kW, the mass flow rate of the liquid stream is 2.04 kg/s, and the mass flow rate of the vapor stream is 4.30 kg/s.

In summary, the problem involves the calculation of flow power, mass flow rate of the two outlet streams, and specific enthalpy difference for a vapor separation unit. The solution requires the use of thermodynamic property tables and mass balance equation.

To know more about mass refer here:

https://brainly.com/question/18064917#

#SPJ11

To determine the flow power needed and the mass flow rate of the outlet streams, we need to use the given information and the properties of R-134a.

Given:

Inlet flow rate (m_dot) = 5.8 L/s

Inlet pressure (P) = 320 kPa

Quality (x) = 55%

First, we need to convert the flow rate from liters to cubic meters and the pressure from kilopascals to pascals:

Inlet flow rate (m_dot) = 5.8 L/s = 0.0058 m^3/s

Inlet pressure (P) = 320 kPa = 320,000 Pa

Next, we can calculate the mass flow rate (m_dot) using the following formula:

m_dot = (P * V_dot) / (R * T)

where:

P = Pressure (in Pa)

V_dot = Volume flow rate (in m^3/s)

R = Specific gas constant for R-134a (in J/(kg·K))

T = Temperature (in K)

The specific gas constant for R-134a is approximately 207.9 J/(kg·K).

Let's assume the outlet streams are fully separated, with one stream being the liquid portion and the other stream being the vapor portion. Since we don't have the specific fraction of the liquid and vapor streams, we cannot determine the exact mass flow rate for each outlet stream.

However, if we assume the liquid and vapor streams are of equal mass, then we can divide the total mass flow rate equally between the two streams:m_dot_outlet_1 = m_dot_outlet_2 = m_dot / 2

Now, we can calculate the flow power (W_dot) using the following formula:W_dot = (m_dot * h_inlet) - (m_dot_outlet_1 * h_outlet_1) - (m_dot_outlet_2 * h_outlet_2)

where:

h_inlet = Enthalpy at the inlet (in J/kg)

h_outlet_1 = Enthalpy at outlet 1 (in J/kg)

h_outlet_2 = Enthalpy at outlet 2 (in J/kg)

To calculate the flow power, we need the enthalpy values at the inlet and outlet states. These values depend on the temperature and quality of the R-134a.

Unfortunately, the given information does not provide the temperature of the R-134a. Without the temperature, we cannot determine the enthalpy values and, consequently, the flow power and mass flow rates of the outlet streams.

To know more about power refer here

https://brainly.com/question/14379882#

#SPJ11

Cauterizing an incision or wound therapy is the therapy that is associated with light waves, but not sound waves. The correct option is (C).

A medical treatment called cauterizing an incision or wound includes burning or coagulating tissues with heat or electricity in order to stop bleeding or hasten wound healing. The main objective of cauterization is to produce a thermal action that closes off blood vessels in order to provide hemostasis and stop excessive bleeding.

During surgical procedures, cauterization is frequently performed to stop bleeding, remove or destroy aberrant tissue, or close off blood arteries. In some medical treatments, such as the removal of skin tags or warts, it is also utilized.

Hence, the therapy is associated with light waves, but not sound waves cauterizing an incision or wound. Option (C) is correct.

To learn more about Waves, here:

https://brainly.com/question/19477984

#SPJ12

The complete question is:

A: breaking down kidney stones

B: acoustically targeting the delivery of a drug

C: cauterizing an incision or wound

D: ablating tumors

Heat transfer that occurs in the situations that follow. If heat transfer is not responsible for the situation that is  conduction

Option A is correct.

Conduction is the cycle by which heat energy is communicated through impacts between adjoining particles or atoms. In contrast to gases, where the distance between the particles is greater, solids and liquids have a higher rate of conduction.

Conduction is the interaction by which intensity is moved from the more sizzling finish to the colder finish of an item. Heat spontaneously flows along a temperature gradient, and the object's thermal conductivity, or k, is its capacity to conduct heat.

Learn more about heat conduction :

brainly.com/question/30416117

#SPJ4

The correct answer is option C. Chemical.

A chemical reaction is a process in which chemical bonds between atoms are broken and reformed, resulting in the creation of new substances with different properties from the original ones. During a chemical reaction, the atoms of the reactant molecules rearrange themselves to form new products, which can have different physical and chemical properties than the original substances.

Chemical reactions can be classified into different types based on the nature of the reactants and the products formed. For instance, a synthesis reaction is a type of chemical reaction in which two or more substances combine to form a more complex compound, while a decomposition reaction is a reaction in which a compound is broken down into simpler substances.

Chemical reactions are fundamental to many natural and industrial processes, from the production of fuels and materials to the metabolism of living organisms. Understanding the mechanisms and properties of chemical reactions is crucial for many fields of science, including chemistry, biochemistry, and materials science.

In conclusion, a chemical reaction is a process in which substances change to other substances as chemical bonds break and reform. It is a fundamental concept in chemistry and has important applications in many scientific and industrial fields.

Know more about chemical reaction click here:

https://brainly.com/question/29762834

#SPJ11

Answer:

The amount of gravitational force INCREASES as the distance between two objects increases; thus, an astronauts weight DECREASES as she or he moves away from earth into space.

hope this helped.

The effective resistance of the TV set is 35.6 ohms (Ω).

To find the effective resistance of the TV set, we can use Ohm's Law, which states that Voltage (V) = Current (I) × Resistance (R). We need to rearrange the formula to solve for resistance: R = V / I.

Given the information in your question:
Current (I) = 2.5 A
Voltage (V) = 89 V

Now we can calculate the resistance (R):
R = V / I
R = 89 V / 2.5 A
R = 35.6 Ω

The effective resistance of the TV set is 35.6 ohms (Ω).

To learn more about current, refer below:

https://brainly.com/question/13076734

#SPJ11

The best table to describe the parts of the atom is a 3 column table with 3 rows. The first column is labeled Particle and contains the entries Proton, Electron, and Neutron.

Atom is an open source, cross-platform text editor developed by GitHub. It is a hackable text editor that can be customized to suit the user’s needs and preferences. It is based on Electron, a framework for building cross-platform applications using web technologies such as HTML, CSS and JavaScript. Atom supports multiple panes, allowing users to open and edit multiple files at the same time. It also offers syntax highlighting for a range of programming languages, a built-in package manager for adding new packages, and a selection of themes to customize the look of the editor.

The second column is labeled Charge and contains the entries Positive, 0, and Negative. The last column is labeled Location and contains the entries Inside Nucleus, Outside Nucleus, and Inside Nucleus.

To learn more about atom

https://brainly.com/question/621740

#SPJ4

The length of the pendulum is 0.389 m.

The length of a simple pendulum can be calculated using the equation:

T = 2π√(L/g)

where T is the period of the pendulum, L is the length of the pendulum, and g is the acceleration due to gravity.

Rearranging the equation to solve for L, we get:

L = (gT²)/(4π²)

Substituting the given values, we get:

L = (9.8 m/s²)(3.15 s)²/(4π²) = 0.389 m

As a result, the pendulum's length is 0.389 m.

A longer pendulum will have a longer period and a shorter pendulum will have a shorter period, all other factors remaining constant. Similarly, a higher acceleration due to gravity will result in a shorter period, while a lower acceleration due to gravity will result in a longer period.

To know more about the Pendulum, here

https://brainly.com/question/29511476

#SPJ4

The time period between the lightning and thunder is 10.09 seconds.

The velocity of sound in the tube was 1009.2 m/s

The time period between the lightning and thunder can be calculated using the equation: distance = speed × time. Since we know the distance (3.50 km) and the speed of sound at 30.0 °C (347.2 m/s), we can rearrange the equation to solve for time: time = distance / speed. Plugging in the numbers, we get: time = 3.50 km / 347.2 m/s = 10.09 seconds.

The velocity of sound in the tube can be calculated using the formula: velocity = frequency × wavelength. The wavelength can be found by doubling the distance between two consecutive nodes or crests. In this case, the wavelength is 2 × 56.5 cm = 113 cm = 1.13 m. Plugging in the frequency (894 Hz) and the wavelength (1.13 m), we get: velocity = 894 Hz × 1.13 m = 1009.2 m/s. Since the velocity is closest to the standard velocity of Helium (1007 m/s), we can conclude that Helium was in the tube.

To know more about the Lightning, here

https://brainly.com/question/15412090

#SPJ4

The distance of the galaxy from Earth is approximately 34 Mpc or 111 million light-years away.

The distance of the galaxy from Earth can be calculated using Hubble's law, which states that the recessional velocity of a galaxy is proportional to its distance from Earth.

The proportionality constant is known as the Hubble constant, denoted by H. The current estimated value of the Hubble constant is approximately 73.3 km/s/Mpc.

To convert the given velocity from miles per hour to kilometers per second, we need to divide it by 2.237 × 10^5. Thus, the recessional velocity of the galaxy in km/s is approximately 2510 km/s.

Using Hubble's law, we can calculate the distance of the galaxy from Earth by dividing its velocity by the Hubble constant.

Therefore, the distance of the galaxy from Earth is approximately 34 Mpc or 111 million light-years away.

To know more about  Hubble's law, refer here:

https://brainly.com/question/13705068#

#SPJ11

After refueling with an additional 800 kg of jet fuel, the military airplane with a mass of 7,800 kg and an initial velocity of 30 m/s will have a new velocity of approximately 28.1 m/s.

According to the conservation of momentum, the total momentum of a closed system remains constant. In this case, the system consists of the military airplane before and after refueling.

Before refueling, the momentum of the airplane is given by: p1 = m1v1 where m1 = 7,800 kg is the mass of the airplane and v1 = 30 m/s is its velocity.

After refueling, the momentum of the airplane is given by: p2 = (m1 + m2)v2     where m2 = 800 kg is the mass of the added fuel and v2 is the final velocity of the airplane.

Since momentum is conserved, we have: p1 = p2 which gives: m1v1 = (m1 + m2)v2  Solving for v2, we get: v2 = (m1v1)/(m1 + m2)  Substituting the given values, we get: v2 = (7,800 kg × 30 m/s)/(7,800 kg + 800 kg) ≈ 28.1 m/s

To know more about velocity , refer here:

https://brainly.com/question/31479424#

#SPJ11

The fire started on the third floor of the building.

People smoking in bed can start fires.

A light switch with worn electrical wiring was found on the third floor.

A substantial risk factor for fire dangers is smoking in bed. This is due to the fact that cigarettes, cigars, and other smoking materials can continue to be hot for a number of hours after being put out.

Smoking materials can ignite flammable items like bedding or furniture if a smoker falls asleep while smoking or fails to properly discard them. This can cause a fire to swiftly spread across the entire room. One of the main causes of tragic fires in houses and other places is smoking in bed.

Learn more about fire incident:https://brainly.com/question/28159595

#SPJ1

There are 0.486 grams of magnesium in 0.02 moles of magnesium.

To calculate the grams of magnesium, you multiply the given moles (0.02 mol) by the molar mass (24.3 g/mol):

0.02 mol Mg × 24.3 g/mol Mg = 0.486 g Mg

Therefore, there are 0.486 grams of magnesium in 0.02 moles of magnesium.

It's important to note that molar mass allows us to convert between moles and grams. By multiplying the number of moles by the molar mass, we can determine the mass of the substance in grams.

This conversion is commonly used in chemistry to relate the quantity of a substance in moles to its corresponding mass in grams.

In this case, by multiplying the given moles (0.02 mol) of magnesium by the molar mass of magnesium (24.3 g/mol), we obtain the mass of magnesium in grams (0.486 g).

To learn more about magnesium, refer below:

https://brainly.com/question/1533548

#SPJ11

After the collision, the two objects will stick together and move with a velocity of 5ms in the same direction.

Collision is a physical phenomenon that occurs when two or more objects interact with enough force to cause damage to one or more of the objects. This can occur when two objects come into contact with each other, or when two objects are moving at different speeds and collide with each other. Collisions can be caused by a variety of factors, including the speed and mass of the objects, the angle of their contact, and the surface area of the objects.

Scenario 1:

After the collision, the two objects will stick together and move with a velocity of 5ms in the same direction.

Scenario 2:

After the collision, the two objects will bounce off each other and move in opposite directions with the same velocity of 5ms.

To learn more about collision

https://brainly.com/question/7221794

#SPJ4

The fraction of the substance remaining is 6.25%.

The amount of substance left is calculated as follows;

N = N₀(1/2)^(t/T)

where;

T is the half-life of the substance,

we have;

N₀ = 100g,

T = 5670 years, and

t = 22680 years

N = 100 x (1/2)^(22680/5670)

N = 6.25 g

The fraction remaining is calculated as follows

fraction remaining = N/N₀

fraction remaining = 6.25/100

fraction remaining = 0.0625 or 6.25%

Learn more about half life here: https://brainly.com/question/2320811

#SPJ1

The Sun appears bigger and brighter than other stars in the sky because it is much closer to the Earth than any other star.

While the Sun is only an average-sized star, it is still much closer to us than any other star, so it appears larger and brighter in the sky.

Additionally, the Sun is also the closest star to the Earth that undergoes nuclear fusion, which is the process that produces its energy and makes it shine.

Other stars in the sky may be much larger or brighter than the Sun, but their distance from us makes them appear much smaller and dimmer.

To know more about nuclear fusion refer here

https://brainly.com/question/12701636#

#SPJ11

A woman lifts up a laundry basket 1.5m and carries it 20m across the room in 15s.

Work is done on the laundry basket both in lifting the basket and in walking across the room during the entire 15s.

Lifting the basket:

The work done in lifting the basket is equal to the force applied multiplied by the distance lifted. The force applied is the weight of the basket, which is equal to the mass of the basket multiplied by the acceleration due to gravity (9.8 m/s^2).

Let's assume the mass of the basket is 'm'. The work done in lifting the basket vertically is given by:

Work_lift = force_lift × distance_lift = (m × 9.8) × 1.5

Carrying the basket horizontally:

When the woman carries the basket across the room, work is done against the force of friction between the basket and the floor. The work done is equal to the force of friction multiplied by the distance traveled horizontally.

The force of friction can be calculated using the coefficient of friction (μ) and the normal force (N). The normal force is equal to the weight of the basket since it is on a horizontal surface.

Let's assume the coefficient of friction between the basket and the floor is 'μ'. The work done in moving the basket horizontally is given by:

Work_horizontal = force_friction × distance_horizontal = (μ × m × 9.8) × 20

The total work done on the basket during the entire 15s is the sum of the work done in lifting and the work done horizontally:

Total work = Work_lift + Work_horizontal

To learn more about friction, refer below:

https://brainly.com/question/13000653

#SPJ11

After 1.8 hours on the shelf, the activity of the drug tagged with 99m43Tc is approximately 8147 Bq.

Step 1: Calculate the number of half-lives that have passed.

To do this, divide the elapsed time (1.8 h) by the half-life of the isotope (6.05 h).
Number of half-lives = 1.8 h / 6.05 h = 0.2975 half-lives

Step 2: Use the decay formula to calculate the remaining activity.
The decay formula is R = R₀ * (1/2)^(t/T), where R is the remaining activity, R₀ is the initial activity, t is the elapsed time, and T is the half-life.

Step 3: Plug in the values and solve for R.

R = (1.0 x 10^4 Bq) * (1/2)^(0.2975)
R ≈ 1.0 x 10^4 Bq * 0.8147
R ≈ 8147 Bq

So, after 1.8 hours on the shelf, the activity of the drug tagged with 99m43Tc is approximately 8147 Bq.

To know more about activity, refer here:

https://brainly.com/question/31293301#

#SPJ11